Kramer VS-41H2 Manuel utilisateur

-41H2 Quick Start (P/N: 2900-300835QS REV 4)

P/N:

2900- 300835QS

Rev:

Scan for full manual

VS-41H2 Quick Start Guide

This guide helps you install and use your VS-41H2 for the first time.

Go to www.kramerav.com/downloads/VS-41H2 to download the latest user manual and check if firmware

upgrades are available.

Step 1: Check what’s in the box

VS-41H2 4x1 HDMI 2.0 Switcher

1 Set of rack ears 1 Quick start guide

1 Power cord 4 Rubber feet

Step 2: Get to know your VS-41H2

# Feature Function

IR LED

For future use

IR Receiver

For future use

INPUT SELECTOR (1-4)

Press to route HDMI source 1 through 4 to the output

EDID Lock Button

Press to lock the current EDID

5 PATTERN Button Press to activate the test pattern generator. When the generator is active,

press one of the input buttons to select a test pattern

LOCK Button

Press and hold to toggle locking and unlocking the front panel buttons

MUTE Button

Press to toggle muting of the output audio and video

VOLUME Buttons (▲ ▼)

Press ▲ to increase volume, press ▼ to decrease volume (flashes 3 times

when max. or min. value is reached)

AUDIO MUTE Button

Press to toggle muting of the output audio

HDMI INPUTS (1-4) Connectors

Connect to up to 4 HDMI sources

HDMI OUTPUTS MONITOR Connector

Connects to an HDMI monitor

HDMI OUTPUTS OUT Connector

Connects to an HDMI acceptor

AUDIO IN 3.5mm Mini Jack

Connects to an unbalanced stereo audio acceptor

AUDIO OUT Terminal Block Connector

Connects to a balanced stereo audio acceptor

RS-232 9-pin D-sub Connector

Connects to a local RS-232 source

ETHERNET RJ-45 Connector

Connects to a network for control (LEDs: activity–flashing green, link–orange)

RESET Button

Press while power-cycling the device to reset to factory default parameters

PROGRAM Mini USB Connector

Used for upgrading the firmware

19 REMOTE IR 3.5mm Connector For future use

20 REMOTE LEDS (1-4, G) Terminal Block Connects to external LED indicators

# Feature Function

REMOTE SELECTOR (1-4, G) Terminal Block

Connects to external contact closure input switches

22 SETUP DIP-switches (1-8) N/A

23 Power Connector with Fuse 100-240V AC connector, enabling power supply to the unit

Step 3: Install the VS-41H2

Attach the rubber feet and place on a table or mount the VS-41H2 in a rack using the included rack ears.

Step 4: Connect the inputs and outputs

Always switch OFF the power on each device before connecting it to your VS-41H2.

For optimum range and performance, use the recommended Kramer cables available at www.kramerav.com/product/VS-41H2

RJ-45 pinout:

Connect the audio output:

For the Ethernet and HDBaseT connectors, use the

following

wiring diagram:

To a balanced stereo audio

acceptor:

To a unbalanced stereo

audio acceptor:

PIN EIA /TIA 568B

Wire Color

Orange / White

Orange

Green / White

Blue

Blue / White

Green

Brown / White

Brown

Step 5: Connect the power

Connect the power cord to the VS-41H2 and plug it into the mains electricity.

Safety Instructions

Caution:

There are no operator serviceable parts inside the unit.

Warning:

Use only the power cord that is supplied with the unit.

Warning:

Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.

Warning:

Disconnect the power and unplug the unit from the wall before installing.

See www.KramerAV.com for updated safety information.

Step 6: Operating the VS-41H2

Switch an input to an output:

•Press an input button (1 to 4) to switch that input to the output.

Generate a test pattern:

For diagnostic purposes, you can generate up to four test patterns:

•Press PATTERN.

•Press any of the input buttons to select a test pattern.

The selected test pattern appears on the outputs.

•To exit the test pattern, press PATTERN once again.

Table des matières

Autres manuels Kramer Changer

Kramer

Kramer VS-21DVI Manuel utilisateur

Kramer

Kramer KDS-SW2-EN7 Manuel utilisateur

Kramer

Kramer VS-28 Manuel utilisateur

Kramer

Kramer VP-719x1 Manuel utilisateur

Kramer

Kramer VP-734 Manuel utilisateur

Kramer

Kramer WP-211T Manuel utilisateur

Kramer

Kramer DIP-31 Manuel utilisateur

Kramer

Kramer VP-730 Manuel utilisateur

Kramer

Kramer VS-55 Manuel utilisateur

Kramer

Kramer VP-1201 Manuel utilisateur

Kramer

Kramer VP-773A Manuel utilisateur

Kramer

Kramer ASPEN-1616UX Manuel utilisateur

Kramer

Kramer VP-720DS Manuel utilisateur

Kramer

Kramer VP-24 Manuel utilisateur

Kramer

Kramer VP-81SIDN Manuel utilisateur

Kramer

Kramer VW-4 Manuel utilisateur

Kramer

Kramer WP-5VH2 Manuel utilisateur

Kramer

Kramer VP-440 Manuel utilisateur

Kramer

Kramer VP-436 Manuel utilisateur

Kramer

Kramer VP-440 Manuel utilisateur

Kramer

Kramer VS-21HDMI Manuel utilisateur

Kramer

Kramer VP-734 Manuel utilisateur

Kramer

Kramer VS-121HC Manuel utilisateur

Kramer

Kramer VP-727A Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur