Kramer VP-4x4K Manuel utilisateur

VP-4x4K Quick Start

P/N:

2900- 301261QS

Rev:

Scan for full manual

VP-4x4K Quick Start Guide

This guide helps you install and use your VP-4x4K for the first time.

Go to www.kramerav.com/downloads/VP-4x4K to download the latest user manual and check if firmware

upgrades are available.

Step 1: Check what’s in the box

VP-4x4K 4x4 UXGA/Audio Matrix Switcher

1 Set of rack ears

4 Rubber feet

Kramer RC-IR3 IR Remote Control Transmitter

1 Power cord

1 Quick start guide

Step 2: Get to know your VP-4x4K

Feature

Function

POWER Switch

Illuminated switch for turning the unit ON or OFF

IR Receiver

Signals from the remote control transmitter illuminate the LED

SELECTO

R Buttons

OUT

Select the output to which the input is switched

Select the input to switch to the output

When a signal is detected, the input button illuminates in green

The SELECTOR IN and OUT buttons also store/recall the input/output configurations

ALL Button

Pressing ALL before pressing an input button connects that input to all outputs

For example, press ALL and then Input button # 2 to connect input # 2 to all the outputs

OFF Button

Pressing OFF after pressing an output button disconnects that output from the inputs. To disconnect

all the outputs, press the ALL button and then the OFF button

AFV Button

When illuminated, the audio channels follow the video channels. The button is illuminated when the

AFV mode is selected. If the AUDIO differs from the VIDEO, the TAKE button will flash, and you

have to press the TAKE button to confirm the modification

VID Button

When illuminated, actions relate to video

The VID button is illuminated when in breakaway mode and actions relate to video

AUD Button

When illuminated, actions relate to audio

The AUD button is illuminated when in breakaway mode and actions relate to audio

STO Button

Pressing STO (STORE) followed by an output or an input button stores the current setting

Press the STO and LOCK buttons simultaneously to set the delay time. For example, press STO and

then the Output button # 3 to store in Setup # 3

LOCK Button

Disengages the front panel switches

RCL Button

Pressing RCL (RECALL) followed by an output or an input button displays a stored setup

TAKE Button

Pressing TAKE toggles the mode between the CONFIRM mode and the AT ONCE mode (user

confirmation per action is unnecessary). When in CONFIRM mode, actions are confirmed by

pressing the TAKE key. For example, press STO and then the Output button # 3 to store in Setup # 3

When in the CONFIRM mode, the TAKE button illuminates

AUDIO GAIN

Button

Press to adjust the audio input or output gain

Feature

Function

- Button

Press to decrease the numerical value

By pressing the + or - buttons continuously, you can speed up their response. For step-by-step

response, press and release these buttons as many times as needed

Gain, switching delay time and machine number

+ Button

Press to increase the numerical value

STATUS 7-

segment Display

Displays the selected input switched to the output (marked above each input)

Also displays the number of IN and OUT ports, the firmware version number, the MACHINE # and

the audio gain level

Feature

Function

INPUT 15-pin HD Connectors

Connect to the video sources (from 1 to 4)

OUTPUT 15-pin HD Connectors

Connect to the acceptors (from 1 to 4)

AUDIO INPUTS 3.5mm Mini Jack

Connect to the unbalanced stereo audio sources (from 1 to 4)

AUDIO OUTPUTS Terminal block connectors

Connect to the balanced stereo audio acceptors (from 1 to 4)

PROGRAM Button

Not used (for technical staff use only)

Ethernet Connector

Connects to the PC or other Serial Controller through computer networking

Factory Reset Button

Press to reset to the factory default definitions:

IP number −192.168.1.39

Mask –255.255.0.0

Gateway –0.0.0.0

UDP port –50000

TCP port –5000

Protocol 3000 commands

All 8 Presets deleted

All audio channels set to 0dB

Machine name –the last four digits of the machine's serial number

DHCP disabled

Turn the POWER switch OFF and then ON again while pressing the

Factory Reset button. The unit will power up and load its memory with the

factory default definitions

RS-485 TERM DIP-switch

DIP 1 is for RS-485 Termination, DIP 2 is not used

RS-485 Terminal Block Port

Pins B (-) and A (+) are for RS-485; Pin G (Ground) may be connected to

the shield of the cable if desired

RS-232 9-pin D-sub Connector

Connects to the PC or the Remote Controller

Power Connector with Fuse

AC connector enabling power supply to the unit

Step 3: Mount VP-4x4K

To rack mount the machine, attach both rack ears

(by removing the screws from each side of the

machine and replacing those screws through the

rack ears) or place the machine on a table.

•Ensure that the environment (e.g., maximum ambient temperature &

air flow) is compatible for the device.

•Avoid uneven mechanical loading.

•Appropriate consideration of equipment nameplate ratings should be

used for avoiding overloading of the circuits.

•Reliable earthing of rack-mounted equipment should be maintained.

Step 4: Connect inputs and outputs

Always switch OFF the power on each device before connecting it to your VP-4x4K.

You can connect DVI-U to an analog (VGA, composite or component video) or digital (HDMI™or DVI) source.

The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.

Connecting the audio output

Wiring the RJ 45 Connectors

To a balanced

stereo audio

acceptor:

This section defines the TP pinout, using

a straight pin-to-pin cable with RJ 45

connectors.

EIA /TIA 568B

Wire Color

Orange / White

Orange

Green / White

To an unbalanced

stereo audio

acceptor:

For HDBT cables, it is recommended

that the cable ground shielding be

connected/soldered to the connector

shield.

Blue

Blue / White

Green

Brown / White

Brown

Set the RS-485 TERM DIP-switch

RS-485 TERM

ON for RS-485 line termination with 120OFF

for no RS-485 line termination

When cascading machines, set this DIP-switch

to ON for the first and last units only

(otherwise, set it to OFF)

To achieve specified extension distances, use the recommended Kramer cables available at www.kramerav.com/product/VP-4x4K.

Using third-party cables may cause damage!

Step 5: Connect power

Connect the power cord to VP-4x4K and plug it into the mains electricity.

Safety Instructions (See www.kramerav.com for updated safety information)

Caution:

•For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the

terminal or in the User Manual.

•There are no operator serviceable parts inside the unit.

Warning:

•Use only the power cord that is supplied with the unit.

•Disconnect the power and unplug the unit from the wall before installing.

•Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.

•To ensure continuous risk protection, replace fuses only according to the rating specified on the product label which located on the

bottom of the unit.

Step 6: Operate VP-4x4K

RS-232 and Ethernet:

EDID

EDID data is passed between Input 1 and Output 1

RS-232

Protocol 2000

Protocol 3000 (Default)

Baud Rate:

9600

Baud Rate:

115,200

Data Bits:

Stop Bits:

Parity:

None

Parity:

None

Command Format:

HEX

Command Format:

ASCII

Example (Output 1 to Input 1):

0x01, 0x81, 0x81, 0x81

Example (Output 1 to

Input 1):

#AV 1>1<CR>

Switching Protocol

P2000 -> P3000

P3000 -> P2000

Command:

0x38, 0x80, 0x83, 0x81

Command:

#P2000<CR>

Front Panel:

Press and hold Output 1

and Output 3

simultaneously

Front Panel:

Press and hold Output

1 and Output 2

simultaneously

Ethernet

Default Settings

Reset Settings

IP Address: 192.168.1.39

Power cycle the unit while holding in the Factory Reset button, located on the

rear panel of the unit.

TCP Port #: 5000

UDP Port #: 50000

Technical Specifications

Inputs:

4 UXGA on 15-pin HD connectors

4 unbalanced audio stereo signals on 3.5mm mini plug connectors

Outputs:

4 UXGA on 15-pin HD connectors

4 balanced audio stereo signals on 5-pin terminal block connectors

Max. Output Level:

Video: 2.2Vpp

Audio: >15Vpp

Bandwidth (-3dB):

Video: 400MHz

Audio: 19kHz

Diff. Gain:

0.07%

Diff. Phase:

0.03 Deg.

K-Factor:

<0.05%

S/N Ratio:

Video: 73.5dB @5MHz

Audio: 76dB unweighted

Crosstalk (all hostile):

Video: -48dB @5MHz

Audio: -54dB @1MHz

Controls:

Input-output selector, AFV, VID, AUD, STO, LOCK, RCL, TAKE, DELAY,

MACH. #, RS-485, RS-232, REMOTE IR

Coupling:

Video: DC

Audio: AC

Audio THD + Noise:

0.065% @1kHz

Audio 2nd Harmonic:

0.002% @1kHz

Power Source:

100-240V AC, 18VA max.

Operating Temperature:

0° to +40°C (32° to 104°F)

Storage Temperature:

-40° to +70°C (-40° to 158°F)

Humidity:

10% to 90%, RHL non-condensing

Dimensions:

19” x 7” x 1U (W, D, H) rack mountable

Weight:

2.7kg (6 lbs) approx

Accessories:

Power cord, rack “ears”, Windows®-based control software

Specifications are subject to change without notice at www.kramerav.com

Autres manuels pour VP-4x4K

Autres manuels Kramer Commutateur matriciel

Kramer

Kramer VS-3232D Manuel utilisateur

Kramer

Kramer VP-720DS Manuel utilisateur

Kramer

Kramer VS-88HDCPxl Manuel utilisateur

Kramer

Kramer VS-169TP Manuel utilisateur

Kramer

Kramer VS-88DTP Manuel utilisateur

Kramer

Kramer 84V5 Manuel utilisateur

Kramer

Kramer VS-626 Manuel utilisateur

Kramer

Kramer VS-606xl Manuel utilisateur

Kramer

Kramer VP-1608 Manuel utilisateur

Kramer

Kramer VS-82HDxl Manuel utilisateur

Kramer

Kramer VP-128H Manuel utilisateur

Kramer

Kramer VS-44HN Manuel utilisateur

Kramer

Kramer VS-66HN Manuel utilisateur

Kramer

Kramer VS-1616A Manuel utilisateur

Kramer

Kramer MTX3-34-M Manuel utilisateur

Kramer

Kramer VS-44HDMI Manuel utilisateur

Kramer

Kramer Sierra Pro XL 1204V5 Manuel utilisateur

Kramer

Kramer Sierra Pro XL 1208V5 Manuel utilisateur

Kramer

Kramer 3216S Manuel utilisateur

Kramer

Kramer VS-402XL Manuel utilisateur

Kramer

Kramer Sierra Video 3264V5Sxl Manuel utilisateur

Kramer

Kramer VP-8x8A Manuel utilisateur

Kramer

Kramer VS-8 Series Manuel utilisateur

Kramer

Kramer VS-5x5 Manuel utilisateur

Manuels Commutateur matriciel populaires d'autres marques

Broadcast Tools

Broadcast Tools SS 8.2 Manuel utilisateur

Altimium

Altimium MATF32 Manuel utilisateur

ALFAtron

ALFAtron ALF-MUK44N Manuel utilisateur

Monoprice

Monoprice Blackbird 15377 Manuel utilisateur

PTN

PTN FMX12 Manuel utilisateur

CYP

CYP nT15GX01 Manuel utilisateur

TESmart

TESmart HMA0402A40 Manuel utilisateur

Octava

Octava HD4XSTPMX Manuel utilisateur

Intelix

Intelix FLX-88 Mode d'emploi

Roland

Roland XS-1HD Manuel utilisateur

Atlona

Atlona AT-HDMI-22M Manuel utilisateur

Link

Link HD8X8 Manuel utilisateur

AMX

AMX AVS-OP-2020-117 Instructions et recettes

Lindy

Lindy 38042 Manuel utilisateur

Extron electronics

Extron electronics MTPX Plus Series Manuel utilisateur

Key Digital

Key Digital Champion KD-16x16CS Manuel utilisateur

Shinybow USA

Shinybow USA SB-8811 Manuel utilisateur

Optimus

Optimus Compact Manuel utilisateur