Kramer VSM-4x4A Manuel utilisateur

VSM

-4x4A Quick Start (P/N: 2900-300668QS REV 1)

P/N:

2900- 300668QS

Rev:

Scan for full manual

VSM-4x4A Quick Start Guide

Step 1: Check what’s in the box

VSM-4x4A 4x4 Seamless AV Matrix Switcher/Multi-Scaler

1 Set of rack ears

4 Rubber feet

IR remote control transmitter with batteries

1 Power cord

1 Quick start guide

Step 2: Get to know your VSM-4x4A

# Feature Function

1 IR LED Lights when the unit accepts IR remote commands

IR Receiver

Receives signals from the remote control transmitter

2 OUTPUT/WINDOW Selector

Buttons MATRIX mode: select the output to which the input is switched (A, B, C or D)

VIDEO WALL mode: not used

DUAL mode: select one of the two DUAL windows: A or B for DUAL A; C or D for DUAL B

QUAD mode: not used

3 INPUT Selector Buttons Press to select an HDMI input (from 1 to 4) to switch to the output

4 ALL Button Press ALL followed by an INPUT button to connect that input to all the outputs (not available for

the video wall mode)

5 OFF Button Press after pressing an output button to disconnect the selected output from the inputs. To

disconnect all the outputs, press ALL followed by OFF

6 TAKE Button Press to toggle between the Confirm mode (when in the Confirm mode, the TAKE button lights )

and the At Once mode. When in TAKE mode, front panel buttons actions are implemented after

pressing the TAKE button

7 MODE

Buttons MATRIX Press to operate the system as a matrix switcher

VIDEO WALL

Press to operate as a 2x2 or 1x4 video wall

DUAL

Press to operate as a 4x2 switcher with PIP capabilities

10 QUAD Press to display all four inputs on each of the outputs

11 STO Button Press to store a configuration

RCL Button

Press to recall a configuration

13 IDENTIFY Button Press to indicate on each output, which input is displayed on the output. The display time is set

via the OSD menu

14 MENU Press to access the OSD menu, exit the OSD menu and, when in the OSD menu, move to the

previous level in the OSD screen

# Feature Function

Navigation

Buttons

ENTER

Press to access sub-menu items and select from several settings



Press to decrease numerical values or select from several definitions

Press to move up the menu list values

Press to increase numerical values or select from several definitions



Press to move down the menu list

RESET TO XGA/1080p Button

Press and hold for about 4 seconds to toggle resetting the video resolution to XGA or 1080p

17 PANEL LOCK Button Press and hold for about 2 seconds to lock/unlock the front panel buttons

# Feature Function

18 INPUT HDMI Connectors Connect to the HDMI sources (from 1 to 4)

19 AUDIO OUTPUT A 3.5mm Mini Jack Connect to an unbalanced audio acceptor (from A to D)

AUDIO OUTPUT 5-pin Terminal Block Connector

Connect to a balanced audio acceptor (from A to D)

21 OUTPUT HDMI Connectors Connect to the HDMI acceptors (from A to D); DUAL: when in the dual

operation mode, A, A and B, B

22 ETHERNET Connector Connects to the PC or other Serial Controller through computer networking

23 PROG USB Connector Connect to upgrade the unit

RS-232 9-pin D-sub Port

Connect to the PC or a remote controller

Mains Socket

Connect the mains power cord

26 Mains Fuse Holder Fuse for protecting the device

27 Power Switch Switch for turning the unit ON or OFF

Step 3: Install the VSM-4x4A

To rack mount the machine attach both ear brackets to the machine (by removing the three screws

from each side of the machine and replacing those screws through the ear brackets) or place the

machine on a table.

Step 4: Connect one of the four operation modes

Always switch OFF the power on each device before connecting it to your VSM-4x4A. For best results, we recommend that you always

use Kramer high-performance cables to connect AV equipment to the VSM-4x4A.

The VSM-4x4A is a four-in-one-box device and can operate as a matrix switcher, video wall, dual switcher or quad switcher.

Each of these modes includes several setup options as follows.

Mode Optional Setups

MATRIX Seamless Matrix – 4x4 matrix switcher. The same output resolution is set for all the outputs and video switching

transitions are seamless (zero-time video cuts).

Independent Matrix – 4x4 matrix switcher. Each output resolution is set independently and video switching

transitions are done via a clean, fade-through-black mechanism.

VIDEO WALL 2x2 – The output is displayed on a set of 4 monitors tiled in a 2x2 setting to form a large display. Each output shows

one quarter of the image.

1x4 – The output is displayed on a set of 4 monitors tiled in a 1x4 (1 column x 4 rows). The image can be cropped

and positioned as desired.

DUAL 4x2 switcher that outputs 2 identical A outputs and 2 identical B outputs.

POP (side-by-side) – Each A and B type outputs shows 2 images side-by-side (left and right).

PiP

(picture-in-picture) – Each A and B type outputs shows 2 images one over the other (main and pip).

QUAD

Any four inputs on one screen for each of the four outputs. Each quarter of a screen shows a selected input.

RJ-45 Pinout:

Connect the audio output:

For the Ethernet and HDBaseT connectors, see the proper wiring

diagram below To a balanced stereo audio acceptor

To an unbalanced stereo audio

acceptor

PIN EIA /TIA 568B

1 Orange / White

Orange

Green / White

4 Blue

5 Blue / White

Green

Brown / White

8 Brown

Step 5: Connect the power

Connect AC power to the rear of the VSM-4x4A, switch on its power and then switch on the power on each device.

Step 6: Set operation parameters via OSD menu

Menu Function

Enter the OSD menu via the MENU button on the

front panel or the IR remote control transmitter.

Select a menu item and set parameters as

required. By default, the output resolution is set to

Native, the VSM-4x4A is triggered to read the

EDID of OUTPUT A and change the output

resolution value according to the native resolution

of the display.

Mode Set the operation mode: matrix switcher (seamless or

independent), video wall (2x2 or 1x4), Dual (POP or PIP) or

Quad mode.

Picture Set the picture parameters per operation mode (contrast,

brightness saturation and hue): matrix mode (same for all

outputs), video wall (separate for each output), DUAL

(separate for left (main) and right (PIP), QUAD (separate for

each QUAD).

If you cannot see any images, verify that the

display, TV, or projector is in good working order

and is connected to the VSM-4x4A. If you still do

not see an image, press and hold the RESET TO

XGA/1080p button for about 4 seconds to reset

the outputs to XGA or 1080p resolution.

Output Set the output parameters: resolution, aspect ratio, border

color, input and output labels, bezel correction, and so on.

EDID

Manage EDID: per video input as well as audio EDID.

Source Set the input source parameters: matrix mode (any input to

any output), video wall (one input to all outputs), DUAL (an

input for for left (main) and an input for right (PIP), QUAD (any

input for each QUAD).

Recall/ Store Store and recall setups: store/recall up to 4 setups for each

operation mode.

HDCP

Set the HDCP: for each input and each output.

Other settings: set the power-save mode, the output audio level, the OSD

definitions and Ethernet parameters; perform reset to factory default values and

view device information.

Step 7: Operate via the front panel buttons, Web pages and via the:

IR remote controller: RS-232 and Ethernet:

RS-232

Protocol 3000

Baud Rate:

115,200

Stop Bits:

Data Bits: 8 Parity: None

TCP/IP Parameters

To reset the IP settings to the factory reset values go to : Menu-> Factory-> RESET->Change

the option to YES and press Enter

IP Address: 192.168.1.39 TCP Port #: Not supported

Subnet mask: 255.255.255.0 Default UDP Port #: 50000

Default gateway: 192.168.1.254 Maximum UDP Ports: 4

Full Factory Reset

OSD Go to : Menu-> FACTORY DEFAULT -> Change the option to YES and

press Enter

P3000

Use “FACTORY” command

Front panel buttons

Press the MENU Button while plugging the power to reset the machine

RS-232/Ethernet (UDP) Command Protocol

Command Format: ASCII

Example (Route the video from the HDMI2 input to the HDMI A output

port in the Matrix mode): #ROUTE 0,1,2<cr>

Autres manuels pour VSM-4x4A

Autres manuels Kramer Commutateur matriciel

Kramer

Kramer 88HD Manuel utilisateur

Kramer

Kramer VS-88DVI Manuel utilisateur

Kramer

Kramer XL 3232VS Manuel utilisateur

Kramer

Kramer VS-48HDCPxI Manuel utilisateur

Kramer

Kramer VP-729 Manuel utilisateur

Kramer

Kramer 84V5S Manuel utilisateur

Kramer

Kramer VP-719DS Manuel utilisateur

Kramer

Kramer VS-808TP Manuel utilisateur

Kramer

Kramer VS-808DS Manuel utilisateur

Kramer

Kramer VP-1608 Manuel utilisateur

Kramer

Kramer VS-66HDMI Manuel utilisateur

Kramer

Kramer Sierra Pro XL 1208V3 Manuel utilisateur

Kramer

Kramer 3232S Manuel utilisateur

Kramer

Kramer VS-88FO Manuel utilisateur

Kramer

Kramer VS-606xl Manuel utilisateur

Kramer

Kramer VP-2x2 Manuel utilisateur

Kramer

Kramer VS-62DT Manuel utilisateur

Kramer

Kramer Sierra Pro XL 1616V3S Manuel utilisateur

Kramer

Kramer XL 1204V Manuel utilisateur

Kramer

Kramer Sierra Video 1204V5 Manuel utilisateur

Kramer

Kramer VS-88HDCPxl Manuel utilisateur

Kramer

Kramer VS-88HD Manuel utilisateur

Kramer

Kramer VS-622DT Manuel utilisateur

Kramer

Kramer VP-4x8 Manuel utilisateur

Manuels Commutateur matriciel populaires d'autres marques

Broadcast Tools

Broadcast Tools SS 8.2 Manuel utilisateur

Altimium

Altimium MATF32 Manuel utilisateur

ALFAtron

ALFAtron ALF-MUK44N Manuel utilisateur

Monoprice

Monoprice Blackbird 15377 Manuel utilisateur

PTN

PTN FMX12 Manuel utilisateur

CYP

CYP nT15GX01 Manuel utilisateur

TESmart

TESmart HMA0402A40 Manuel utilisateur

Octava

Octava HD4XSTPMX Manuel utilisateur

Intelix

Intelix FLX-88 Mode d'emploi

Roland

Roland XS-1HD Manuel utilisateur

Atlona

Atlona AT-HDMI-22M Manuel utilisateur

Link

Link HD8X8 Manuel utilisateur

AMX

AMX AVS-OP-2020-117 Instructions et recettes

Lindy

Lindy 38042 Manuel utilisateur

Extron electronics

Extron electronics MTPX Plus Series Manuel utilisateur

Key Digital

Key Digital Champion KD-16x16CS Manuel utilisateur

Shinybow USA

Shinybow USA SB-8811 Manuel utilisateur

Optimus

Optimus Compact Manuel utilisateur