Kramer MTX3-88-SE Manuel utilisateur

MTX3-88-SE Quick Start

P/N:

2900- 301644QS

Rev:

Scan for full manual

MTX3-88-SE Quick Start Guide

This guide helps you install and use your MTX3-88-SE for the first time.

Go to www.kramerav.com/downloads/MTX3-88-SE to download the latest user manual and check if

firmware upgrades are available.

Step 1: Check what’s in the box

MTX3-88-SE 8X8 Seamless Matrix Switcher

1 Set of rack ears

4 Rubber feet

1 Power Cord

1 Quick Start Guide

Step 2: Get to know your MTX3-88-SE

Feature

Function

ON LED (behind the logo)

On when power is supplied to the unit.

IN SELECT Buttons (1 to 8)

Press to select the input to switch after selecting an output (also used for storing

matrix presets).

OUT SELECT Buttons (1 to 8)

Press to select an output to which the input is routed.

ALL Button

Press followed by an input button selection to connect the selected input to all

outputs.

For example, press ALL and then press IN 2. Input 2 is routed to all outputs.

OFF Button

Press after pressing an output button to disconnect the selected output from the

inputs.

To disconnect all the outputs, press ALL followed by OFF.

MULTI-VIEW

Press once to enable one of the MULTI-VIEW modes (button LED lights): 1 X PIP,

2 X PIP, or Quad.

Press any lit MULTI-VIEW button to return to Matrix mode (enabled by default,

button LED turns off).

For more details, refer to Step 4:Defining Multi-View operation modes.

IDENTIFY Button

After pressing this button, the multi-view window number is displayed via OSD (On

Screen Display) for about 10 seconds within each multi-view window

RECALL Button

Press to recall a preset configuration: Recall a stored preset from any of the 8

presets via the front panel input buttons (1 to 8).

STORE Button

Press to store a configuration: Store 8 presets via the front panel input buttons

(1 to 8).

RESET TO 1080p Button

Press and hold button for about 2 sec to set output resolution to 1080p.

PANEL LOCK Button

Press and hold to toggle the locking/release of the front panel buttons.

Feature

Function

HDMI/HDBT

INPUTS

HDBT 1 RJ-45 Connector

Connect to an HDBT transmitter and/or HDMI source.

Input 1 is user configurable. You can select the active input

connector via web-UI.

HDMI 1 Connector

HDMI 2-8 Connectors

Connect to an HDMI source (2-8).

AUDIO OUTPUTS

5-pin Terminal Block

Connectors

AUDIO OUTPUT 1-2

Connect to a stereo balanced audio acceptor (1 to 2) to output De-

embedded audio from HDMI Output 1 or Output 2.

AUDIO OUTPUT A-B

Connect to a stereo balanced audio acceptor (A to B) to output De-

embedded audio from any HDMI 3-7 Outputs (default Output 3, or

4).

HDBT IN

IR (Rx, Tx) left 2-pins on a

5-pin Terminal Block

Connectors

Connect to the IR connector of an HDBT output (Tx to Rx and Rx to

Tx), to extend IR signal between an HDBT transmitter on the input

and HDBT receiver on an output.

RS-232 (G, Rx, Tx) right 3-pins

on a 5-pin Terminal Block

Connectors

Connect to a serial controller or RS-232 controlled device for RS-

232 signal extension via the HDBT input.

HDBT OUT-1

HDBT OUT-2

IR (Rx, Tx) left 2-pins on a

5-pin Terminal Block

Connectors

Connect to the IR connector of an HDBT input (Tx to Rx and Rx to

Tx), to extend IR signal between an HDBT receiver on an output

and an HDBT transmitter on an input.

RS-232 (G, Rx, Tx) right 3-pins

on a 5-pin Terminal Block

Connectors

Extend RS-232 signal between the HDBT port and the HDBT

receiver: Connect to serially control a device connected to the

HDBT receiver; or to serially control a local device using a controller

connected to the HDBT receiver.

HDMI/HDBT

OUTPUTS

HDBT/HDMI RJ-45/HDMI

Connectors (1 to 2)

Connect to an HDBT receiver and/or HDMI acceptor (mirrors HDBT

output signal).

HDMI Connectors (3 to 8)

Connect to HDMI acceptors.

HDMI Connectors (8/9)

Connect to an HDMI acceptor. Output 9 mirrors Output 8.

CNTL (Rx, Tx) 2-pin Terminal Block Connector

(GND is common for CNTL and RS-232)

Connect to a PC to control MTX3-88-SE.

RS-232 (G, Rx, Tx) 3-pin Terminal Block Connector

Connect to a serially-controlled device to control the unit via IP

(Default TCP port: 5001).

LAN RJ-45 Connector

Connect to the LAN.

SETUP

For configuring the functionality of the IR and RS-232 ports

For more details, refer to the MTX3-88-SE User Manual.

Power Illuminated Switch

Turn the device on and off.

Mains Power Connector and Fuse

Plug in the power cord.

Step 3: Mounting MTX3-88-SE

To rack mount the matrix, attach both

rack ears (by removing the screws from

each side of the matrix and replacing

those screws through the rack ears) or

place the matrix on a table.

•Ensure that the environment (e.g., maximum ambient

temperature & air flow) is compatible for the device.

•Avoid uneven mechanical loading.

•Appropriate consideration of equipment nameplate

ratings should be used for avoiding overloading of the

circuits.

•Reliable earthing of rack-mounted equipment should be

maintained.

Step 4: Defining Multi-View operation modes

You can preset the multi-view configuration via the front panel buttons and select the specific inputs for each preset

configuration via the embedded web pages. Seamless matrix mode is the default operation mode.

Press

Function Description

Result per Output

PiP 1 –MTX3-88-SE operates as an 8X4 seamless multi-view

matrix, with each output supporting a PIP overlay. Outputs

2,4,6,8 are disabled and outputs 1,3,5,7 may have a parent

picture and overlayed PIP insert.

PiP 2 –MTX3-88-SE operates as an 8X2 seamless multi-view

matrix, with each output supporting 2 PIP overlays. Outputs 2-4,

7-8 are disabled, and output 1&5 may have a parent picture and

2 overlayed PIP inserts.

QUAD –MTX3-88-SE operates as an 8X2 seamless multi-view

matrix, with a quad layout on each output. Outputs 2-4, 6-8 are

disabled, and output 1&5 consists of 4 (1/4 screen sized)

pictures.

Step 5: Connect inputs and outputs

Always switch OFF the power on each device before connecting it to your MTX3-88-SE.

Connecting the audio output

Wiring the RJ-45 Connectors

To a balanced

stereo audio

acceptor:

This section defines the TP pinout, using

a straight pin-to-pin cable with RJ-45

connectors.

EIA /TIA 568B

Wire Color

Orange / White

Orange

Green / White

To an unbalanced

stereo audio

acceptor:

For HDBT cables, it is recommended

that the cable ground shielding be

connected/soldered to the connector

shield.

Blue

Blue / White

Green

Brown / White

Brown

To achieve specified extension distances, use the recommended Kramer cables available at www.kramerav.com/product/MTX3-88-SE.

Using third-party cables may cause damage!

Step 6: Connect power

Connect the power cord to MTX3-88-SE and plug it into the mains electricity.

Safety Instructions (See www.kramerav.com for updated safety information)

Caution:

•For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.

•There are no operator serviceable parts inside the unit.

Warning:

•Use only the power cord that is supplied with the unit.

•Disconnect the power and unplug the unit from the wall before installing.

•Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.

•To ensure continuous risk protection, replace fuses only according to the rating specified on the product label which located on the bottom of the unit.

Step 7: Operate MTX3-88-SE

Operate MTX3-88-SE via:

•Front panel buttons

•Remotely, by RS-232 serial

commands transmitted by a

touch screen system, PC, or

other serial controller

•Embedded web pages via the

Ethernet

RS-232 Control / Protocol 3000

Baud Rate:

115,200

Parity:

None

Data Bits:

Command Format:

ASCII

Stop Bits:

Example: (Switch video input 2 to output 4): #V 2>4<CR>

Default IP Parameters

Fallback IP

Address:

192.168.1.39

UDP Port #:

50000

Fallback Subnet

Mask:

255.255.255.0

TCP Port #:

5000

Fallback Gateway:

0.0.0.0.

Default Username:

admin

Default Password:

Admin

Switch an input to an output

Press an output button followed by an input button to switch the selected input to the selected output.

Store a switching preset

1. Configure the switching as required for the preset.

2. Press STO button. The STO button flashes.

3. Select an input button (1-8) to choose the preset number.

Recall a switching preset

1. Press RCL. The RCL button flashes.

2. Press the relevant input button that stored the preset.

The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.

Autres manuels pour MTX3-88-SE

Autres manuels Kramer Commutateur matriciel