Kontron KISS Stor Slim Manuel utilisateur

KISS Stor Slim

KISS Stor Slim Quick Installation Guide

Package Contents

zKISS Stor Slim RAID box.

zTwo disk drive carriers.

zKISS Stor Slim Quick Installation Guide.

zKISS Stor Slim user kit CD. (User’s Manual and GUI software)

zRS-232 cable with bracket and serial cable for COM port.

zDisk drive mounting screws.

zTwo keys for drive carriers. (identical)

Know your KISS Stor Slim

zKISS Stor Slim Front view:

Access LED indicator for indicating that hard disk is been accessing.

Status LED indicator for indicating that disk current status.

KISS Stor Slim

zKISS Stor Slim Rear view:

1. SATA DC power input connector

2. SATA host connector

3. RS232 connector (J10)

4. Reserved for feature/function expand (J9 default is closed)

5. Standard AT/ATX DC power input connector

zStatus of all LED indicators KISS Stor Slim

The table lists all matches of 2 LED indicators for indicating status of RAID

box.

Status indicator

Red/Green

Access indicator

Yellow

RAID status

Green Off Disk is installed, no access

Green On/flash Disk is being accessing

Red Off No disk installed or disk failure

Flash (Red/Green) On/flash Disk is rebuilding

KISS Stor Slim

Setup your KISS Stor Slim

1. Load hard drives to each drive carriers, and secure the hard drives by

screwing.

2. Power down your host computer and mount the RAID box in the host.

3. Connect the SATA or IDE cable and DC power cable to RAID box from host

computer.

4. Connect the RS-232 cable to RAID box RS-232 port and COM port of the host.

(Option for upgrading firmware or GUI remote monitor)

Caution

urn off and disconnect all electrical power from the system

before be

innin

installation.

Note

There is a triangular symbol “▲” on both PCB

connector(J10) and RS-232 cable connector, please

make sure that you connect in the right direction (both

triangle symbols match each other).

KISS Stor Slim

Start to use your KISS Stor SATA

Application 1: Two new disk drives.

1. Install and lock all drive carriers and they are ready for use.

2. Power on the host computer.

3. After system boot up, the RAID box will be recognized as Accusys KISS

Stor Slim by host system. And system treats it as a single disk.

4 Partition and format the RAID box before it can be used.

Application 2: Installing one disk drive with data and one new disk

drive.

1. The new disk drives must have the same capacity or larger capacity than

the drive with data.

2. Lock the disk with data at the top drive carrier and leave the new disks

unlocked at the bottom drive carriers. This identifies the disk with data as

the source drive. (The host computer must in power off state.)

3. Power on the host computer.

4. Lock the bottom drive.

5. The RAID box will immediately begin mirroring the data from the source

drive to the new disk drive in bottom drive carrier. Any old data on the

new disk drive will be lost, and is overwritten with the mirror image of the

source drive.

Contact Kontron Embedded Computers GmbH

•Support: [email protected]

Note

If you have installed non-identical hard disk drives,

your computer will recognize RAID box

as a single hard

disk with a capacity equal to the smaller hard disk drive

installed in the RAID box.

Table des matières

Autres manuels Kontron Matériel informatique

Kontron

Kontron MOPSlcdLX Manuel utilisateur

Kontron

Kontron 820951 ADD2-DVI-Dual-Internal Manuel utilisateur

Kontron

Kontron X-Board UPA 63036 Manuel utilisateur

Kontron

Kontron 3.5-SBC-APL V2.0 Manuel utilisateur

Kontron

Kontron KBox F-420-WLU Manuel utilisateur

Kontron

Kontron ePCI-201 Manuel utilisateur

Kontron

Kontron PEP CP321 Manuel utilisateur

Kontron

Kontron COMh-caRP Manuel utilisateur

Kontron

Kontron microETXexpress-SP Manuel utilisateur

Kontron

Kontron cPCI-MXS64GX Manuel du produit

Kontron

Kontron PCI-946-1 Manuel du produit

Kontron

Kontron MSP8020 Series Manuel utilisateur

Kontron

Kontron PC/104-PCMCIA-1 Manuel utilisateur

Kontron

Kontron CP6930 Manuel utilisateur

Kontron

Kontron COM Express Eval 10 Manuel utilisateur

Kontron

Kontron KTQ67/Flex Manuel utilisateur

Kontron

Kontron CP-ADAP-P47-PB (3U) Manuel utilisateur

Kontron

Kontron KBox E-200 Series Manuel utilisateur

Kontron

Kontron cPCI-MXS64 Manuel du produit

Kontron

Kontron nanoETXexpress-HMI Baseboard Manuel utilisateur

Kontron

Kontron ETX -CN8 Manuel utilisateur

Kontron

Kontron SMARC-sAMX8 Manuel utilisateur

Kontron

Kontron CP6003-SA Manuel utilisateur

Kontron

Kontron 082-0220-00 Backplane Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur

Advantech

Advantech ASMB-935 Series Manuel utilisateur

Jupiter

Jupiter RAM PACK Manuel utilisateur