Konica Minolta HT-509 Manuel utilisateur
E-1
INSTALLATION MANUAL
A4NH-9550-01
HT-509 Heater
I. Accessory parts
*1 To install the heater to a paper feed cabinet, 14
wire saddles are used.
*2 To install the heater to the Desk, this wire saddle
is not used.
Note:
• To use the heater HT-509, the paper feed cabi-
net PC-110/210/410 or Desk DK-510 as well as
the power supply Box MK-734 are required.
• This manual provides the illustrations of the
accessory parts and machine that may be
slightly different in shape from yours. In that
case, instead of the illustrations, use the
appearance of your machine to follow the
installation procedure. This does not cause any
significant change or problem with the proce-
dure.
• When the heater HT-509 and the transformer
kit TK-101 are installed at the same time, install
the heater first.
No. Name Shape Q’ty
1. Heater
1
2. Wire saddle
(large) 1
3. Wire saddle
(medium) *1
15
4. Wire saddle
(small) *2
1
5. Edge cover
2
6. Screw
4
7. Installation
manual 1
set
After unpacking, be sure to get rid of the
packaging materials and keep them out of
the reach of children.
Putting the head in the plastic bag
involves danger of suffocation.
A4NHIXC001DA
A4NHIXC030DA
A4NHIXC029DA
A4NHIXC031DA
A4NHIXC028DA
9J08IXC078DA
4980IXC019DA
Applied Machines: C554/C454/C364/C284/C224
COLOR MFP: 55 ppm/45 ppm/36 ppm/28 ppm/22 ppm
Product Code: A2XK/A4FJ/A161/A4FK/A4FM
E-2
II. Installation procedures
Note:
• When the paper feed cabinet or Desk is not
installed in the main unit, go to step 1 in page
E-4.
• When the paper feed cabinet or Desk is
installed in the main unit, perform the steps
described below.
<When the paper feed cabinet or Desk is installed
in the main unit>
1. Turn off the machine and unplug the power cord
from the power outlet.
2. Pull out the 1st and 2nd paper feed trays from the
main unit.
3. Remove two stoppers and remove the 1st and
2nd paper feed trays. (Two screws)
4. Pull out the tray from the paper feed cabinet/
Desk.
Note:
For the paper feed cabinet PC-110/210, pull out
the upper tray.
5. Remove the rear cover from the paper feed cabi-
net/Desk. (Five screws)
6. Remove the knockout from the rear cover using
nippers.
A4NHIXC004DA
A4NHIXC005DA
A4NHIXE040DA
A4NHIXE019DA
E-3
7. <When installing the heater to the paper feed cabinet>
Attach the supplied wire saddle (small) to the
paper feed cabinet at the position shown in the
illustration.
<When installing the heater to the Desk>
Attach the supplied wire saddle (medium) to the
Desk at the position shown in the illustration.
8. Move the harness through the back side, and set
the heater into the mounting position.
Note:
Set the heater’s position mounting slot by aligning
it with the plate bosses.
9. Route the harness of the heater through the wire
saddle attached in step 7.
10. Secure the heater. (Four supplied screws)
11. Set the 1st and 2nd paper feed trays in the main
unit and attach the two stoppers. (Two screws)
12. Close all trays.
A4NHIXC020DA
A4NHIXE035DA
A4NHIXC043DA
A4NHIXE025DA
Wire saddle
A4NHIXC008DA
E-4
13. Attach supplied 14 wire saddles (medium), one
wire saddle (large), and two edge covers.
Note:
Attach the wire saddle (large) to the hole marked
with “8.”
14. Route the harness of the heater through the
three wire saddles and edge cover.
* For information on the following steps, refer to the
installation manual of the power supply Box MK-
734.
<When the paper feed cabinet/Desk is not
installed in the main unit>
Note:
If protective tape or protective materials are
attached to the paper feed cabinet/Desk, refer to
the installation manual of each option and remove
them in advance.
1. Pull out the tray from the paper feed cabinet/
Desk.
Note:
For the paper feed cabinet PC-110/210, pull out
the upper tray.
2. Remove the rear cover from the paper feed cabi-
net/Desk. (Five screws)
Note:
If the extender harnesses are taped, remove the
tape.
A4NHIXE026DA
Wire saddle (large)
A4NHIXE027DA
A4NHIXC015DA
A4NHIXE016DA
Extender harness
E-5
3. Remove the knockout from the rear cover using
nippers.
4. <When installing the heater to the paper feed cabinet>
Attach the supplied wire saddle (small) to the
paper feed cabinet at the position shown in the
illustration.
<When installing the heater to the Desk>
Attach the supplied wire saddle (medium) to the
Desk at the position shown in the illustration.
5. Move the harness through the back side, and set
the heater into the mounting position.
Note:
Set the heater’s position mounting slot by aligning
it with the plate bosses.
6. Route the harness of the heater through the wire
saddle attached in step 4
A4NHIXE019DA
A4NHIXC020DA
A4NHIXE035DA
A4NHIXE045DA
A4NHIXE025DA
Wire saddle
E-6
7. Secure the heater. (Four supplied screws)
8. Close all trays.
9. Install the paper feed cabinet/Desk to the main
unit.
Note:
• For information on the installation procedure,
refer to the installation manual of each option.
• When placing the main unit on the paper feed
cabinet, be careful not to get the extender har-
nesses caught between the main unit and the
paper feed cabinet.
* Go to step 13 in page E-4 for the following steps.
A4NHIXE039DA
Table des matières
Autres manuels Konica Minolta Accessoires pour imprimantes
Konica Minolta
Konica Minolta IT-101 Comment utiliser
Konica Minolta
Konica Minolta MAGICOLOR 4600 Series Manuel utilisateur
Konica Minolta
Konica Minolta VI-506 Manuel utilisateur
Konica Minolta
Konica Minolta FS-503 Manuel utilisateur
Konica Minolta
Konica Minolta FS-110 Manuel utilisateur
Konica Minolta
Konica Minolta Image Controller IC-205 Manuel utilisateur
Konica Minolta
Konica Minolta bizhub 361 Manuel utilisateur
Konica Minolta
Konica Minolta PK-517 Manuel utilisateur
Konica Minolta
Konica Minolta RU-513 Manuel utilisateur
Konica Minolta
Konica Minolta DF-704 Manuel utilisateur
Konica Minolta
Konica Minolta LU-302 Manuel utilisateur
Konica Minolta
Konica Minolta HD-524 Manuel utilisateur
Konica Minolta
Konica Minolta DB-209 Comment utiliser
Konica Minolta
Konica Minolta FOCUS Manuel utilisateur
Konica Minolta
Konica Minolta DK-510 Manuel utilisateur
Konica Minolta
Konica Minolta FS-532 Manuel utilisateur
Konica Minolta
Konica Minolta EK-608 Manuel utilisateur
Konica Minolta
Konica Minolta WT-513 Manuel utilisateur
Konica Minolta
Konica Minolta Di1611 Manuel utilisateur
Konica Minolta
Konica Minolta magicolor 2430 DL Manuel utilisateur
