Kollmorgen PC830 Guide de démarrage rapide

PC830 Firmware Upgrade Instructions

Before you begin Remove AC power from the drive and wait 5 minutes until the bus discharges.

Warning

High voltages are present on the PC830 connections. Follow the instructions

outlined below to avoid an electrical shock.

Tools required ·Small flat head screw driver

·Medium phillips screwdriver

·Chip extraction tool (supplied in upgrade kit)

Procedure There are static sensitive devices inside the drive. Perform installation in static

free environment.

1. Unconfigure drive to clear non-volatile (NV) memory.

2. Remove all external connections from the drive.

3. Remove the screw that attaches the plastic cover to the aluminum heatsink.

Make sure the drive has been powered down for at least 5 minutes.

4. Use a small flat head screwdriver to gently lift the two plastic tabs that hold

the cover in place. Once both plastic tabs are free from the aluminum tabs

the cover should slide freely.

903-083002-01 PC830 Firmware Upgrade Installation 1

Procedure

(cont’d) 5. Remove the (2) screws that attach the control board to the aluminum

heatsink.

6. Move the control board gently from side to side while pulling upward away

from the drive.

7. Once the power board header is free from the control board socket, maneuver

the board and attached bracket to free them from the drive.

8. Place the control board, component side up, on a flat surface.

2PC830 Firmware Upgrade Installation 903-083002-01

Location of U1

Procedure

(cont’d) 1. Use the extractor tool supplied to remove the chip from the board as shown

in the figure above.

Note: The prongs on the tool should be inserted into the diagonal slots in the

socket and under the chip.

2. Install the new chip. The flat corner of the chip designates pin 1. It is

important when installing the chip that the orientation of pin 1 is correct.

Caution

Failure to orient the chip properly could result in a damaged chip and/or control

board.

3. Once the chip is oriented properly, push down firmly on the chip until it snaps

firmly into the socket.

4. Replace the control board using care to make sure all the pins from the

power board align properly with the control board socket.

5. Re-install the two screws that attach the control board to the cover.

6. Slide the plastic cover back on until the plastic tabs latch with the aluminum

tabs and replace the screw to secure the cover. When sliding the cover back

on pay careful attention to the slots in the cover. These should align with the

control board and the cover should slide on easily.

Note: Ensure that the plastic tabs on the side of the cover, as well as the tabs on

the top and bottom of the cover, line up with the heatsink.

903-083002-01 PC830 Firmware Upgrade Installation 3

Table des matières

Autres manuels Kollmorgen servomoteur

Kollmorgen

Kollmorgen AKD PROFINET RT Communication Manuel utilisateur

Kollmorgen

Kollmorgen SERVOSTAR CD Series Manuel utilisateur

Kollmorgen

Kollmorgen AKD 2G Manuel utilisateur

Kollmorgen

Kollmorgen AKM2 Manuel utilisateur

Kollmorgen

Kollmorgen SL3000 Manuel utilisateur

Kollmorgen

Kollmorgen AKD2G-S Series Manuel utilisateur

Kollmorgen

Kollmorgen SERVOSTAR 300 Manuel d'installation et d'exploitation

Kollmorgen

Kollmorgen AKD-x00306 Manuel utilisateur

Kollmorgen

Kollmorgen AKD-N00607 Manuel utilisateur

Kollmorgen

Kollmorgen AKM1 Manuel utilisateur

Kollmorgen

Kollmorgen S70101 Manuel utilisateur

Kollmorgen

Kollmorgen AKM11B Manuel de la liste des pièces

Kollmorgen

Kollmorgen S700 Series Manuel d'installation et d'exploitation

Kollmorgen

Kollmorgen EB-10X Series Manuel

Kollmorgen

Kollmorgen AKD series Manuel utilisateur

Kollmorgen

Kollmorgen MKD-C Series Manuel d'utilisation

Kollmorgen

Kollmorgen AKD-N series Manuel utilisateur

Kollmorgen

Kollmorgen AKD PDMM series Manuel utilisateur

Kollmorgen

Kollmorgen AKMH Series Manuel utilisateur

Kollmorgen

Kollmorgen SERVOSTAR S300 Manuel de réparation

Kollmorgen

Kollmorgen SERVOSTAR 300 Manuel utilisateur

Kollmorgen

Kollmorgen AKD Manuel utilisateur

Kollmorgen

Kollmorgen AKD Manuel utilisateur

Kollmorgen

Kollmorgen S700 Series Manuel d'installation et d'exploitation

Manuels servomoteur populaires d'autres marques

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J5 MR-J5-G Series Manuel utilisateur

Robotis

Robotis XH430-W350-T Manuel utilisateur

NTI AG

NTI AG LinMot C1250 Series Manuel utilisateur

Welcon

Welcon WE2A D048 Series Manuel utilisateur

Parallax

Parallax 900-00005 Manuel utilisateur

Festo

Festo TP 1410 Manuel utilisateur

Axor

Axor MAGNUM 400 Manuel utilisateur

Siemens

Siemens SINAMICS S120 Manuel utilisateur

Danfoss

Danfoss 176F6494 Manuel utilisateur

THORLABS

THORLABS TDC001 Manuel utilisateur

TECO

TECO JSDAP Series Manuel utilisateur

Rockwell Automation

Rockwell Automation Allen-Bradley Kinetix 6000 Manuel utilisateur

GSK

GSK DA98D Manuel utilisateur

Lenze

Lenze m850 Mode d’emploi

Baumuller

Baumuller b maXX 3000 Manuel

Baumuller

Baumuller b maXX 5000 Manuel

Baumuller

Baumuller b maXX 5500 Manuel

Danfoss

Danfoss VLT HVAC Drive FC 102 Manuel utilisateur