Kodak Slide Projector Manuel utilisateur
Operating Manual
CONSUMER IMAGING
KODAK
CAROUSEL®
Slide Projector
Important Safety Instructions
When using your projector, always follow basic safety precautions:
1. Read and understand all instructions before using this equipment.
2. Operate this projector with 110- to 125-volt 60 Hz current only. Incorrect voltage can cause projector
malfunction.
3. Close supervision is necessary when any appliance is used by or near children, or others who may not
understand the need for these precautions. Do not leave the projector unattended during use.
4. Be careful not to touch hot parts. For lamp replacement, allow the module to cool before touching the
lamp and the surrounding area. Do not place the lamp module on heat-sensitive surfaces.
5. Do not operate your projector if the cord is damaged or if the projector has been dropped or damaged
(see “How to Obtain Service” on page 29).
6. Position the cord so that it is not tripped over, pulled, or placed in contact with hot surfaces.
7. If an extension cord is necessary, use a cord with a current rating at least equal to that of the projector.
Cords rated for less amperage than the projector may overheat.
8. Always unplug the projector from the electrical outlet before cleaning and servicing and when it is not
in use.
9. Allow the projector to cool before storing.
10. Do not immerse this equipment in water or other liquids.
11. Do not disassemble this projector. Use a qualified service technician when service or repair is required.
Incorrect reassembly can cause electric shock the next time the projector is used.
12. Use only safety electrical low-voltage (SELV) devices.
13. The use of an accessory attachment not recommended by the manufacturer may increase risk of
damage.
14. Keep the air-flow vents unobstructed.
Save These Instructions
Operating Manual
KODAK
CAROUSEL
Slide Projector
KODAK CAROUSEL® Slide Projector 1
Contents
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . .Inside Front Cover
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Loading the Slide Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Projecting Your Slides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Editing Your Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Clearing a Gate Jam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Using the Built-In Viewer (Model 5600 Only) . . . . . . . . . . . . . . . . . .18
Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Changing the Projection Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Cleaning the Condenser, Heat-Absorbing Glass, and Mirror . . . . . . .22
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
How to Obtain Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Serial Number
The serial number of your projector is printed on the label affixed to the power
cord retainer on the base of the projector. Record this number, as well as the
model identification, date, and place of purchase, for future reference.
2 KODAK CAROUSEL® Slide Projector
Introduction
Congratulations!
You have just purchased a KODAK CAROUSEL Slide Projector which:
• triples lamp life
• provides brighter and more vivid colors!
Introduction
Take the time to read the instructions in this operating manual to become
familiar with your KODAK CAROUSEL®Slide Projector and how to operate
it properly.
KODAK CAROUSEL® Slide Projector 3
Overview
FRONT RIGHT
BACK RIGHT
BASE
1 – Tray
2 – Lock Ring
3 – Storage Compartment/Remote
4 – Elevating Foot
5 – Elevating Adjustment Wheel
6 – Elevating Foot Release Button
7 – Lens
8 – Viewer (Model 5600)
9 – Focus Knob
10 – Select Bar
11 – Timer (Model 5600)
12 – Reverse
13 – Forward
14 – Power/Fan/Lamp
15 – Tray Release Latch
16 – Lamp Module
17 – Reading Light
18 – Room Light Outlet (Model 5600)
19 – Remote Control Receptacle
20 – Power Cord
21 – Power Cord Retainer
22 – Leveling Foot
4 KODAK CAROUSEL® Slide Projector
Operation
Operation
Startup
Open the storage compartment and remove the remote control.
Plug the 5-pin cable remote connector into the remote-control receptacle,
aligning the raised dot with the metallic rivet head.
Plug the power cord into a grounded outlet with 110- to 125-volt 60 Hz
current only.
KODAK CAROUSEL® Slide Projector 5
Operation
Loading the Slide Tray
A KODAK CAROUSEL®140 Slide Tray is designed to hold up to 140 slides.
Be sure that your slide mounts are in good condition; frayed or bent mounts
may fail to drop into the projector. A variety of slide trays are available with
capacity up to 140 slides. See your dealer in Kodak products for a complete
list of Kodak trays and accessories.
Note: Do not attempt to project slides mounted with sticky or loose tape.
Place the tray over the center post of the projector. Align the "0" slot with the
gate index; the tray will drop into position.
If your 140-slide tray does not drop easily, secure the lock ring, invert the
tray, and align the index hole with the index notch. Slide and hold the tray
release latch in the direction of the arrow, and turn the bottom plate until the
index hole and notch align. Then release the latch. If you use an 80-slidetray,
rotate the metal plate on the bottom of the tray until it locks into position.
140-Slide Tray 80-Slide Tray
6 KODAK CAROUSEL® Slide Projector
Operation
Adding Your Slides Remove the lock ring by turning it counterclockwise and lifting it off.
Check each slide’s orientation (horizontal or vertical), and arrange them in the
order you wish to show them. Then turn the slides upside down.
Number each mount in the upper right-hand corner of the film’s shiny side.
Insert your first slide into the first slot in the tray so that the number is visible
on the outer circumference of the tray. Insert your second slide in the second
slot with the emulsion (dull side) facing your first slide, and so on.
Ce manuel convient aux modèles suivants
4
Table des matières
Autres manuels Kodak Projecteur
Kodak
Kodak EKTAPRO 7010 Manuel utilisateur
Kodak
Kodak LUMA 150 Manuel utilisateur
Kodak
Kodak CAROUSEL BC5601 Manuel utilisateur
Kodak
Kodak Pocket Pico Projector Manuel utilisateur
Kodak
Kodak DP1100 - Digital Projector Manuel utilisateur
Kodak
Kodak DP850 - Ultra Digital Projector Manuel utilisateur
Kodak
Kodak EKTAPRO 9020 CINE Manuel utilisateur
Kodak
Kodak Luma 75 Manuel utilisateur
Kodak
Kodak V600 Manuel utilisateur
Kodak
Kodak EKTAPRO Manuel utilisateur
Kodak
Kodak 5600 - BC5601 Carousel Projector Manuel utilisateur
Kodak
Kodak Carousel S-RA2000 Manuel utilisateur
Kodak
Kodak Instamatic M80 Manuel utilisateur
Kodak
Kodak EKTAPRO 7010 Manuel du propriétaire
Kodak
Kodak EKTAGRAPHIC III AM Manuel utilisateur
Kodak
Kodak DP1050 ULTRA Manuel utilisateur
Kodak
Kodak V600 Manuel utilisateur
Kodak
Kodak DP900 - Digital Projector Manuel utilisateur
Kodak
Kodak Carousel S-AV28 Mode d'emploi
Kodak
Kodak Ektalite 500 Manuel utilisateur
Manuels Projecteur populaires d'autres marques
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur
NEC
NEC NP600S EDU Manuel utilisateur
BenQ
BenQ SH753P Manuel utilisateur
Eiki
Eiki EK-623U series Manuel utilisateur
Epson
Epson PowerLite Pro Cinema 6020UB Manuel utilisateur
Epson
Epson PowerLite Home Cinema 705HD Manuel utilisateur
