Juniper Day One Plus SRX380 Manuel utilisateur

Day One+

SRX380

IN THIS GUIDE

Step 1: Begin | 1

Step 2: Up and Running | 6

Step 3: Keep Going | 9

Step 1: Begin

IN THIS SECTION

Meet the SRX380 | 1

Install the SRX380 | 2

Power On | 4

Meet the SRX380

The Juniper Networks®SRX380 Services Gateway is a high-performance, all-in-one secure SD-WAN gateway. It provides

your network with superior and reliable WAN connectivity while consolidating security, routing, and switching for distributed

enterprise offices. With sixteen 1-Gigabit Ethernet PoE+ ports and four 10-Gigabit Ethernet ports, the SRX380 provides

greater port density than other models in the SRX300 line of devices, all in a 1-U form factor.

Install the SRX380

IN THIS SECTION

What’s in the Box? | 2

What Else Do I Need? | 2

Install the SRX380 in a Rack | 3

What’s in the Box?

•SRX380 Services Gateway

•Power cord appropriate for your geographic location

•RJ-45 cable

•DB-9 adapter

•USB console cable

•Power cord retainer clip

•Rack mount kit with:

•Six flat-head 4-40 mounting screws

•Twelve flat-head M4x6-mm Phillips mounting screws

•Four mounting brackets (includes two 2-inch-recess brackets) that attach to the mounting rails

•Two mounting rails

•Two mounting blades

What Else Do I Need?

You’ll need to provide:

•Someone to help you screw the SRX380 into the rack

•Eight rack mount screws

•A number two Phillips (+) screwdriver

Install the SRX380 in a Rack

Before you begin the installation, review General Safety Guidelines and Warnings.

Here’s how to install the SRX380 in a rack:

1. Review General Safety Guidelines and Warnings

2. Wrap and fasten one end of the electrostatic discharge (ESD) grounding strap around your bare wrist, and connect the

other end to a site ESD point.

3. Attach the mounting brackets to the side mounting rails using the six flat-head mounting screws.

g100945

2—1—Mounting railMounting bracket

4. Attach the mounting rails to the sides of the SRX380 using the M4x6-mm Phillips flat-head mounting screws.

g100946

5. Lift the SRX380 and position it in the rack. Line up the bottom hole in each mounting bracket with a hole in each rack

rail, making sure the SRX380 is level.

6. While you’re holding the SRX380 in place, have a second person insert and tighten the rack mount screws to secure

the mounting brackets to the rack rails. Make sure they tighten the screws in the two bottom holes first and then

tighten the screws in the two top holes.

g100947

7. Continue holding the SRX380 in place and have the second person slide the mounting blades into the channel of the

mounting rails.

g100948

8. Screw the mounting blades to the rack using the rack mount screws.

9. Check that the mounting brackets on each side of the rack are level.

Power On

Now that you’ve installed your SRX380 in the rack, you’re ready to connect it to power.

1. Wrap and fasten one end of the electrostatic discharge (ESD) grounding strap around your bare wrist, and connect the

other end to a site ESD point.

2. Attach a grounding cable to earth ground and then attach it to the SRX380’s grounding points.

g100950

3. On the SRX380 rear panel, push the end of the retainer strip into the slot above the power cord socket until the strip

snaps into place.

4. Press the small tab on the retainer strip to loosen the loop.

5. Slide the loop until you have enough space to insert the power cord into the power cord socket.

6. Insert the power cord firmly into the power cord socket.

7. Slide the loop on the retainer strip toward the power supply until it is snug against the base of the power cord coupler.

8. Press the tab on the loop and draw out the loop into a tight circle.

g100940

9. If the AC power source outlet has a power switch, turn it off.

10. Plug in the AC power cord to the power source outlet.

11. If the AC power source outlet has a power switch, turn it on.

12. Verify that the PWR LED on the front panel is solid green.

Step 2: Up and Running

IN THIS SECTION

Configure Root Authentication | 6

Plug and Play | 7

Customize the Basic Configuration | 8

Now that the SRX380 is powered on, let’s do some initial configuration to get the switch up and running on the network.

It’s simple to provision and manage the SRX380 and other devices on your network. You can choose the configuration

tool that’s right for you:

•J-Web—This tool comes preinstalled on the SRX380 and includes a Setup wizard that walks you through the configuration.

•CLI commands

•Juniper Sky™ Enterprise, Juniper Networks-hosted public cloud-based Software as a Service (SaaS) solution.

NOTE: You’ll need to have a Juniper Sky Enterprise subscription service before you can use it to configure

the SRX380. For more information, check out the Juniper Sky Enterprise Getting Started Guide.

Configure Root Authentication

1. Connect the management port (MGMT) on the SRX380 front panel to the Ethernet port on your laptop.

g100951

The SRX380 functions as a DHCP server and automatically assigns an IP address to the laptop.

Ensure that the laptop acquires an IP address on the 192.168.1.0/24 network.

2. If the laptop is unable to get an IP address, manually configure an IP address in the 192.168.1.0/24 network.

Be sure you don’t assign the IP address 192.168.1.1 to the laptop because this is the IP address assigned to the SRX380.

3. Set the root authentication password:

a. Open a browser and type https://192.168.1.1. You don’t need to log in.

The J-Web Setup wizard opens on your screen.

b. Click Skip in the upper-right corner of the Setup wizard.

c. Set a root authentication password and click OK. The J-Web login page appears.

Plug and Play

The SRX380 already has factory-default settings configured right out of the box to make it a plug-and-play device. So all

you have to do to get the SRX380 up and running is connect it to your LAN and WAN networks. Here’s how:

1. Connect the WAN network to port 0/0.

2. Connect the LAN network to any of the ports from 0/1 through 0/18.

3. Check to see if the SRX380 is connected to the Internet. Go to http://www.juniper.net. If the page doesn’t load, check

the Internet connection.

After you complete these steps, you can start using the SRX380 on your network right away. You can go back and customize

settings at anytime. The J-Web Setup wizard is always available to you.

Customize the Basic Configuration

To customize basic settings using the J-Web Setup wizard, have these values handy:

•Hostname

•Root authentication password

•IP address for the NTP server

•IP address for the DNS server

•IP address for the management interface

1. In the J-Web application, select Configure > Setup Wizard. The Setup wizard opens on your screen.

2. Select the configuration mode that’s right for you and then follow the screens as they appear in the Setup wizard:

•Standard—Configure basic security settings for the SRX380.

•Cluster (HA)—Set up the SRX380 in chassis cluster mode.

•Passive—Set up the SRX380 in Tap mode. Tap mode enables the SRX380 to passively monitor traffic flows across

a network.

Step 3: Keep Going

Congratulations! Your SRX380 is configured and ready to go. Here are some things you can do next:

ThenIf you want to

See Activate Junos OS Licenses in the Juniper Licensing

Guide

Download, activate, and manage your software licenses

to unlock additional features for your SRX services

gateway

Juniper Sky Enterprise and use the more advanced

configuration features it offers.

NOTE: You’ll need an account activation code to access the

Juniper Sky Enterprise portal. For more information see the

Juniper Sky Enterprise Getting Started Guide.

Change configuration settings, get another device up

and running, or both

Visit the SRX380 Documentation page in the Juniper

TechLibrary

See all documentation available for the SRX380

See the SRX380 Hardware Installation GuideFind more in-depth information about installing and

configuring the SRX380

Visit Day One: SRX Series Up and Running With Advanced

Security Services

Set up your SRX380 with advanced security measures

to protect and defend your network

See Installing Software on SRX Series DevicesManage software upgrades for your SRX380

See the Junos OS Release NotesStay up-to-date on new and changed features and

known and resolved issues

Juniper Networks, the Juniper Networks logo, Juniper, and Junos are registered trademarks of Juniper Networks, Inc. in the

United States and other countries. All other trademarks, service marks, registered marks, or registered service marks are the

property of their respective owners. Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper

Table des matières

Autres manuels Juniper Matériel réseau

Juniper

Juniper WX 100 Manuel utilisateur

Juniper

Juniper SRX5400 Manuel de service

Juniper

Juniper NFX150 Instructions d'installation

Juniper

Juniper MX150 Instructions d'installation

Juniper

Juniper JSA7500 Manuel utilisateur

Juniper

Juniper NFX150-S1 Manuel utilisateur

Juniper

Juniper NFX250-S1 Manuel utilisateur

Juniper

Juniper MX10016 Instructions d'installation

Juniper

Juniper JSA7800 Manuel utilisateur

Juniper

Juniper SSR1300 Manuel utilisateur

Juniper

Juniper JSA1500-BSE Manuel utilisateur

Juniper

Juniper JCS1200 Mode d’emploi

Juniper

Juniper Junos Space JA2500 Instructions d'installation

Juniper

Juniper CTP2000 Series Manuel utilisateur

Juniper

Juniper SRX300 Series Manuel utilisateur

Juniper

Juniper SSR1200 Manuel utilisateur

Juniper

Juniper SSR1500 Manuel utilisateur

Juniper

Juniper SSG5 Manuel

Juniper

Juniper G10 CMTS Instructions d'installation

Juniper

Juniper SRX340 Instructions d'installation

Juniper

Juniper WX 3400 Manuel utilisateur

Juniper

Juniper MX240 - UPGRADING Manuel utilisateur

Juniper

Juniper SSR1500 Manuel utilisateur

Juniper

Juniper EX4100-F- 24P/T Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur