Juniper BX7000 Manuel utilisateur
Step 1: Install the BX7000 Multi-Access Gateway 1
BX7000 Multi-Access Gateway
Getting Started Guide
This guide provides instructions on connecting the Juniper Networks BX Series
7000 Multi-Access Gateway to a network. For more information, see the BX7000
Multi-Access Gateway Hardware Guide.
Step 1: Install the BX7000 Multi-Access Gateway
The gateway can be installed in a rack or on a wall. Each installation is site-specific.
For more information, see the BX7000 Multi-Access Gateway Hardware Guide.
Step 2: Connect the BX7000 Multi-Access Gateway to External Devices
Connect the gateway to external devices using the console ports, Ethernet ports,
and T1/E1 ports.
Connect to a Management Console
Use either the RJ-45serial console port or the USB console port to connect to a
management console.
BX 7000
CLOCK CARD
EXPANSION CARD
Console
Terminal Backhaul
Network
Cell Site
NOTE: Although cables can be connected to both the RJ-45 serial console port and
the USB console port, only one of the console ports can be active at a time. If both
ports are connected, only the USB port will be active. For more information
regarding the console ports, see the BX7000 Multi-Access Gateway Hardware Guide.
BX 7000 Multi-access Gateway Getting Started Guide
2Step 2: Connect the BX7000 Multi-Access Gateway to External Devices
Connect to the RJ-45 Serial Console Port
Connect the RJ-45 end of the crossover twisted pair cable to the RJ-45 serial console
port of the gateway. Connect the other end of the cable to the serial port of the
management console.
Connect to the USB Console Port
Connect the Type B end of the USB cable to the USB console port of the gateway.
Connect the Type A end of the USB cable to the USB port of the management
console.
Connect to Ethernet Ports
The Ethernet ports provide connections to external devices and can be used either
as data ports or as management ports.
There are three copper Ethernet ports and two fiber-optic Gigabit Ethernet ports, as
shown in the following illustration:
Connect to T1/E1 Ports
The T1/E1 ports provide connections to T1 or E1 networks. Use an RJ45-to-RJ45
interface cable to connect the gateway to networking devices.
USB console port
Copper Gigabit Ethernet ports
RJ-45 console port
Fiber-optic Gigabit Ethernet ports
CONSOLE COPPER COPPER COPPER SFP SFP
ETHERNET 1
ETHERNET 1 ETHERNET 2 ETHERNET 2
ETHERNET 0
CONSOLE
g002909
NOTE: Although cables can be connected to both the copper Ethernet port and the
fiber-optic Ethernet port, in the case of both the Ethernet 1 port and the Ethernet
2 port, the copper port and the fiber-optic port cannot be active at the same time.
If both ports are connected, only the fiber-optic port will be active. For more
information regarding use of the Ethernet ports, see the BX7000 Multi-Access
Gateway Hardware Guide.
Fiber-optic Ethernet ports
Copper Ethernet ports
COPPER COPPER COPPER SFP SFP ALARM
ETHERNET 1
ETHERNET 1 ETHERNET 2 ETHERNET 2
ETHERNET 0
g002908
Step 3: Connect the Grounding Cable 3
BX 7000 Multi-access Gateway Getting Started Guide
Step 3: Connect the Grounding Cable
The gateway has two grounding studs located on the right side of the front panel, as
well as a grounding screw located on the left side at the back of the gateway for
connecting to the ground when the gateway is wall mounted.
To connect the grounding cable :
1. Before making grounding connections, ensure that the grounding surfaces are
clean and that they are brought to a bright finish.
2. Connect one end of the grounding wire to the ground.
3. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and
then connect the strap to one of the ESD points on the chassis.
4. Connect the other end of the grounding cable to either the grounding studs or
the grounding screw.
For more information on grounding the gateway, see the BX7000 Multi-Access
Gateway Hardware Guide.
Step 4: Connect to a Power Source
After grounding, connect the gateway to a power source.
Connect to an AC power source
Use a power cord that has a plug appropriate to your geographical location. For
more information on AC power cord specifications, see the BX7000 Multi-Access
Gateway Hardware Guide.
Connect to a DC power source
To connect the DC power cables:
1. Before connecting to the power supply, verify that the DC power cables are
correctly labeled; and that the customer site power circuit breakers are
switched to the off position.
2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and
then connect the strap to one of the ESD points on the chassis.
3. Secure each power cable lug to the terminal studs. Attach the negative wire lug
to the negative (–) terminal stud and the positive wire lug to the positive (+)
terminal stud.
NOTE: Always ground the gateway before connecting power supplies.
CAUTION: Ensure that the power connections maintain proper polarity.
BX 7000 Multi-access Gateway Getting Started Guide
4Step 5: Power the Gateway On
Step 5: Power the Gateway On
To power the gateway on:
1. Verify that an external management device is connected to a console port on
the gateway.
2. Power the external management device on.
3. Verify that the power supply is fully inserted in the chassis.
4. Verify that the source AC power cord or DC power cables are securely
connected.
5. Switch on the customer site circuit breakers to provide voltage to the power
supply. When the gateway is powered on successfully and diagnostic tests are
complete, the system LED will light green, indicating that the gateway and the
power supplies are functioning normally.
6. Monitor the startup process on the external management device to verify that
the system boots properly. The following messages will be discplayed upon
proper boot :
Completed Successfully.
.
BX7000 login:
Step 5: Log In to the Gateway
To log in to the gateway:
1. At the login prompt, log in to the gateway either as the CLI user or as the root
user and enter the password.
2. To configure the gateway, enter the configure command at the operational
mode prompt.
cli@BX7000> configure
The symbol # indicates that the gateway is in configuration mode.
cli@BX7000#
For more information on configuration and on using the BXOS software, see the
BXOS Configuration Guide and the BXOS CLI Users Guide and Command
Reference.
Step 6: Configure an Ethernet Management Port
Before you can use an Ethernet port for management, you must assign an IP
address and run an SSH client from a host. For more information, see the BX7000
Multi-Access Gateway Hardware Guide.
Safety Warnings 5
BX 7000 Multi-access Gateway Getting Started Guide
Safety Warnings
Only trained and qualified personnel should install or replace the gateway.
Perform only the procedures described in this guide or the BX7000 Multi-Access
Gateway Hardware Guide. Other services should be performed by authorized
service personnel only.
Before installing the gateway, read the guidelines for site preparation in the
BX7000 Multi-Access Gateway Hardware Guide to make sure that the site meets
power, environmental, and clearance requirements for the gateway.
Read the installation instructions before you connect the gateway to a power
source.
When mounting the gateway in a partially filled rack, load the rack from the
bottom to the top, with the heaviest components at the bottom of the rack.
If the rack is provided with stabilizing devices, install the stabilizers before
mounting or servicing the gateway in the rack.
When removing or installing an electrical component, always place it
component-side up on a flat antistatic surface or in an electrostatic bag.
When installing the gateway, always make the ground connection first and
disconnect it last.
WARNING: See installation instructions before connecting the routing node. This is
a summary of safety warnings; for a complete list, including translations, see the
BX7000 Multi-Access Gateway Hardware Guide at
http://www.juniper.net/techpubs/hardware/.
WARNING: Certain ports on the gateway are designed for use as intrabuilding
(within-the-building) interfaces only (Type 2 or Type 4 ports as described in
GR-1089-CORE, Issue 4) and require isolation from exposed outside plant (OSP)
cabling. To comply with NEBS requirements and to protect against lightning
surges and commercial power disturbances, the intrabuilding ports must not be
metallically connected to interfaces that connect to the OSP or its wiring. The
intrabuilding ports on the gateway are suitable for connection to intrabuilding or
unexposed wiring/cables only. The addition of primary protectors does not
provide sufficient protection to metallically connect these interfaces to OSP
wiring.
CAUTION: Before removing or installing components of a gateway, attach an ESD
strap to an ESD point and place the other end of the strap around your bare wrist.
Failure to use an ESD strap could result in damage to the gateway.
BX 7000 Multi-access Gateway Getting Started Guide
6Safety Warnings
Wire the DC power supply using the appropriate lugs. When connecting power,
the proper wiring sequence is ground to ground, +RTN to +RTN, then –48 V to
–48 V. When disconnecting power, the proper wiring sequence is –48 V to –48
V, +RTN to +RTN, then ground to ground.
Do not work on the system or connect / disconnect cables during electrical
storms.
Before working on equipment that is connected to power lines, remove jewelry,
including rings, necklaces, and watches. Metal objects heat up when connected
to power and ground and can cause serious burns or become welded to the
terminals.
Failure to observe these safety warnings can result in serious physical injury.
Part Number: 530-027716-01
Revision 1
Juniper Networks, Inc.
1194 North Mathilda Avenue
Sunnyvale, CA 94089 USA
Phone 408 745 2000
or 888 JUNIPER
Fax 408 745 2100
Copyright Notice
Copyright © 2009 Juniper Networks, Inc. All rights reserved.
Juniper Networks and the Juniper Networks logo are registered trademarks of Juniper Networks, Inc. in the United
States and other countries. All other trademarks, service marks, registered trademarks, or registered service marks in
this document are the property of Juniper Networks or their respective owners. All specifications are subject to change
without notice. Juniper Networks assumes no responsibility for any inaccuracies in this document or for any obligation
to update information in this document. Juniper Networks reserves the right to change, modify, transfer, or otherwise
revise this publication without notice.
Revision History
November 2008
BX 7000 Multi-access Gateway Getting Started Guide
Safety Warnings 7
Autres manuels pour BX7000
1
Table des matières
Autres manuels Juniper Porte
Juniper
Juniper SRX3400 Instructions d'installation
Juniper
Juniper SRX1500 Guide de configuration
Juniper
Juniper SRX550 Instructions d'installation
Juniper
Juniper SRX 210 Manuel utilisateur
Juniper
Juniper SRX3600 Instructions d'installation
Juniper
Juniper SRX-4600 Manuel utilisateur
Juniper
Juniper SRX 210 Manuel utilisateur
Juniper
Juniper SRX240 Series Instructions d'installation
Juniper
Juniper SRX 210 Manuel utilisateur
Juniper
Juniper SRX 1400 SERVICES GATEWAY - Manuel utilisateur
Juniper
Juniper SRX550 Manuel utilisateur
Juniper
Juniper SRX550 Manuel utilisateur
Juniper
Juniper SRX340 Instructions d'installation
Juniper
Juniper SRX340 Instructions d'installation
Juniper
Juniper SRX220 Manuel utilisateur
Juniper
Juniper SRX 5800 Manuel utilisateur
Juniper
Juniper SRX4100 Instructions d'installation
Juniper
Juniper SRX 210 Instructions d'installation
Juniper
Juniper SRX Series Manuel utilisateur
Juniper
Juniper SRX 210 Manuel utilisateur
Manuels Porte populaires d'autres marques
LST
LST M500RFE-AS Manuel utilisateur
Kinnex
Kinnex Media Gateway Manuel utilisateur
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuel utilisateur
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur
Telsey
Telsey CPVA 500 - SIP Manuel utilisateur
