Johnson 40-6060 Manuel utilisateur

Magnetic Digital Level

Model No. 40-6060

Instruction Manual

Congratulations on your choice of this Magnetic Digital Level. We

suggest you read this instruction manual thoroughly before using the

instrument. Save this instruction manual for future use.

8305H-All_Manuals 8/18/14 8:02 AM Page 1

Table of Contents

1. Kit Contents

2. Features and Functions

3. Location of Parts/Components

4. Operating nstructions

5. Using the Product

6. Self-Check & Fine Calibration

7. Technical Specifications

8. Care and Handling

9. Product Warranty

10. Trouble Shooting

1. Kit Contents

Description for Model 40-6060 Qty.

Magnetic Digital Level 1

“AAA” Alkaline Batteries 3

Soft-Sided Pouch 1

nstruction Manual 1

2. Features and Functions

• Angle inclination in 5 construction languages - units of measure

(degrees, percent, mm/m, in/ft in decimal, in/ft in fractional)

• Working range of angle measurement 0º to 90º

• 0º and 90º - position of inclination is confirmed by a signal tone

• Automatic digit inversion for overhead measurements

• Hold-function to freeze measurement

• Magnetic base

• 1/4” - 20 thread for connection to tripod

8305H-All_Manuals 8/18/14 8:02 AM Page 2

3. Location of Part/Components

LCD D splay

Battery Compartment

8305H-All_Manuals 8/18/14 8:02 AM Page 3

4. perating Instructions

Battery Installation

1. Make sure the digital level is

turned off.

2. Turn the battery compartment

cover screw counter-

clockwise to remove the cover.

Remove the old batteries, and

install the new batteries.

Note:

1. Be sure to match up polarities

when replacing the batteries.

2. Always remove the batteries before storing the instrument.

Display after Installing Batteries:

1. After installing new batteries, the LCD will display “good” and

then show “-0-”.

2. Calibrate the instrument as described in self-check & fine

calibration.

IMP RTANT: t is the responsibility of the user to verify the

calibration of the instrument before each use.

8305H-All_Manuals 8/18/14 8:02 AM Page 4

5. Using the Product

Key Guide

There are four key pads on this instrument, they are (from left

to right): calibration/sound key, mode key, hold/backlight key and the

power on/off key.

Calibration/Sound Key

A short press will activate the sound function. A long press

(more than 2 seconds) will activate the calibration function.

Periodic checking should be conducted to this instrument. f it is out

of alignment, recalibration will be necessary. This key pad is used for

horizontal and vertical calibration of the instrument. See the

“Self-Check and Calibration” in section 6.

Push the Cal/Sound a short press to turn on the horn (symbol

will be displayed). Push again to turn off. Horn will start a slow beep

at 10º and 80º and beep faster the closer you get to 0º or 90º. Once

the instrument hits 0º or 90º, you will get a steady tone.

Power

On/Off

Display

Calibration/Sound Key Mode Key Hold/Backlight Key

8305H-All_Manuals 8/18/14 8:02 AM Page 5

Automatic Shut-off

This instrument will shut-off automatically if no operation is received

within 20 minutes.

Hold/Backlight Key

Set the level in place and press this key a short press to enter

into the hold status, record the current angle of the flashing

display, the displayed value will not change. Press this key again to

release the hold and the data will vary according to slope. A long

press (more than 2 seconds) will turn on the LCD backlight.

Power n/ ff Key

Power on and off the instrument by pressing this key.

Mode Key

Push the MODE key to switch from one construction language

to another. This controls which construction language your

electronic module will measure in. Your level has the capability to

measure in Degrees, Percentage of slope, Millimeters per Meter, nches

per Foot (Slope/Pitch) in decimal form and nches per Foot in fractions

of an inch. A symbol on the upper right of the screen will display

which MODE you are currently in.

8305H-All_Manuals 8/18/14 8:02 AM Page 6

Low-power Indication

When voltage is low, battery symbol will flash in the left LCD as shown

below. When this is flashing, batteries need to be replaced.

The figure below shows the left side of the digital level needs to be

moved up to achieve level.

Shows that the digital level is level.

Shows the measurement of the slope.

8305H-All_Manuals 8/18/14 8:02 AM Page 7

6. Self-Check & Fine Calibration

Horizontal Accuracy Check

1. Turn on the digital level and put it on a smooth and level

surface as shown in figure 1. Wait 10 seconds until the display

digits are stable and record the degree reading.

2. Rotate the digital level 180º in the same plane, see figure 2,

wait 10 seconds until the display data is stable then record

the second degree reading.

3. Turn over the digital level in the same plane, figure 3, wait 10

seconds and record the third degree reading when it is stable.

4. Rotate the digital level 180º in the same plane, figure 4, wait

10 seconds and write down the fourth degree reading when

stable.

5. Of the four degree readings, if any two of the values have a

difference over 0.2º, the unit must be recalibrated.

F gure 1 F gure 3

F gure 2 F gure 4

IMP RTANT: t is the responsibility of the user to verify the

calibration of the instrument before each use.

8305H-All_Manuals 8/18/14 8:02 AM Page 8

Vertical Accuracy Check

1. Turn on the digital level and put it on a smooth and vertical

plane as shown in figure 5. Wait 10 seconds until the data

reading is stable and then record the angle degree.

2. Rotate the digital level 180º on the same plane, see figure 6,

wait 10 seconds until the display data is stable then record

the second degree value.

3. Turn over the digital level in the same plane, figure 7, wait 10

seconds and record the third degree value when it is stable.

4. Rotate the digital level 180º in the same plane, figure 8, wait

10 seconds and write down the fourth degree value when

stable.

5. Of the four degree readings, if any two of the values have a

difference over 0.2º, the unit must be recalibrated.

Horizontal Calibration

1. Turn on the instrument and put it on a smooth and horizontal

surface, figure 9. Press and hold in for 2 seconds the Calibration

key, -0- will show on LCD display. Wait 10 seconds then press the

Calibration key again, the LCD will show -1-.

2. Rotate the digital level 180º on the same plane, figure 10, wait 10

seconds and press the Cal key until the LCD displays -2-.

F gure 5 F gure 6 F gure 7 F gure 8

8305H-All_Manuals 8/18/14 8:02 AM Page 9

3. The horizontal calibration is complete.

F gure 9 F gure 10

7. Technical Specifications

Accuracy ±0.1º for 0º and 90º,

and ±0.2º for 1º to 89º

Working Range 0º to 90º

Resolution ±0.1º, 0.1%, 1/8", 0.02", 1.7mm

Power Supply 3 “AAA” alkaline batteries

Battery Life Approx. battery life 100 hours

continuous use

Dimensions 6.45" x 2.3" x 1.25"

(164 x 60 x 32mm)

Weight 0.66 lbs. (0.3 Kg)

Working Temperature 14°F to 113°F (-10°C to +45°C)

Center Screw Thread 1/4" – 20

8305H-All_Manuals 8/18/14 8:02 AM Page 10

Autres manuels pour 40-6060

Table des matières

Langues :

Autres manuels Johnson Niveau laser

Johnson

Johnson 9100 Manuel utilisateur

Johnson

Johnson 40-6688 Manuel utilisateur

Johnson

Johnson 40-6060 Manuel utilisateur

Johnson

Johnson 40-6080 Manuel utilisateur

Johnson

Johnson 40-6692 Manuel utilisateur

Johnson

Johnson 40-6065 Manuel utilisateur

Johnson

Johnson 40-6683 Manuel utilisateur

Johnson

Johnson 40-6535 Manuel utilisateur

Johnson

Johnson 40-6674 Manuel utilisateur

Johnson

Johnson 40-6680 Manuel utilisateur

Johnson

Johnson 40-6647 Manuel utilisateur

Johnson

Johnson 40-6584 Manuel utilisateur

Johnson

Johnson 40-6080 Manuel utilisateur

Johnson

Johnson 40-6670 Manuel utilisateur

Johnson

Johnson 40-6650 Manuel utilisateur

Johnson

Johnson 40-6641 Manuel utilisateur

Johnson

Johnson 40-6936 Manuel utilisateur

Johnson

Johnson JLX LEVEL UP 40-6681 Manuel utilisateur

Johnson

Johnson 1880-2400 Manuel utilisateur

Johnson

Johnson 40-6250 Manuel utilisateur

Johnson

Johnson 40-6650 Manuel utilisateur

Johnson

Johnson 40-6690 Manuel utilisateur

Johnson

Johnson 40-6692 Manuel utilisateur

Johnson

Johnson 40-6646 Manuel utilisateur

Manuels Niveau laser populaires d'autres marques

Nedo

Nedo ET-5 Manuel utilisateur

geo-FENNEL

geo-FENNEL Maxi-Liner FL 65 HP Manuel utilisateur

LaserLiner

LaserLiner X2-Laser Manuel utilisateur

Spectra

Spectra LL300N Manuel utilisateur

geo-FENNEL

geo-FENNEL Selection PRO FLG 40-PowerCross GREEN SP Manuel utilisateur

Nedo

Nedo Crossliner 4 Manuel utilisateur

Lasertec

Lasertec FX360G Manuel utilisateur

Flex

Flex ALC 8 Manuel utilisateur

Black & Decker

Black & Decker LZR5 Manuel utilisateur

Cocraft

Cocraft HL 20-SG Manuel utilisateur

Zircon

Zircon iLine Manuel utilisateur

HWH

HWH 310 SERIES Manuel utilisateur

Leica

Leica iCON robot 60 Manuel utilisateur

LaserLiner

LaserLiner SuperCross-Laser SCL 2 Manuel utilisateur

LaserLiner

LaserLiner ActiveFinder XP Manuel utilisateur

DeWalt

DeWalt DW082 Manuel utilisateur

imex

imex EL20 Manuel utilisateur

Fixturlaser

Fixturlaser NXA D I-0912 Manuel utilisateur