Johnson Controls F4-XPM Series Manuel utilisateur
F4-XPM Expansion Modules Installation Guide
Application
The F4-XPM series expansion I/O modules can serve
in one of two capacities depending on where they are
installed in the system. When installed on the Sensor/
Actuator (SA) Bus of an equipment controller, an XPM
expands the input and output interfaces that can be
used with that equipment controller. When installed on
the Field Controller (FC) Bus of a FX-SNC, an XPM can be
used as I/O point multiplexors to support monitoring and
control from a FX-SNC. The point multiplexor can also
be useful for sharing points between other equipment
controllers on the FC Bus using peer-to-peer connectivity.
XPMs operate on an RS-485 BACnet MS/TP Bus and are
BACnet Testing Laboratory (BTL) listed and certified to the
BACnet Smart Actuator (B-SA) profile.
Communications Protocols
The XPM expansion modules can communicate using
BACnet MS/TP, or wireless Zigbee® using a ZFR/ZFR Pro
Wireless Field Bus Router (on the FC Bus only). By default,
the XPM expansion modules communicate using the
BACnet MS/TP protocol. The BACnet protocol is a standard
for ANSI, ASHRAE, and the International Standards
Organization (ISO) for building controls. To configure
these expansion modules in a wireless application
installation, see Configuring wireless communications.
Note: Using Controller Configuration Tool (CCT)
10.1 and later, FX equipment Controllers can be
configured to communicate using either the BACnet
MS/TP or the N2 field bus networking protocol.
The operation of an XPM on the SA Bus of an
equipment controller is not affected by the selection
of the BACnet MS/TP or the N2 protocol in the host
controller.
North American Emissions Compliance
United States
This equipment has been tested and found to comply
with the limits for a Class A digital device pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference when this equipment is operated in a
commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area may cause harmful interference, in which
case the users will be required to correct the interference
at their own expense.
Canada
This Class (A) digital apparatus meets all the
requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la Classe (A) respecte toutes
les exigences du Règlement sur le matériel brouilleur du
Canada.
Installation
Observe the following guidelines when installing an XPM
expansion module:
• To minimize vibration and shock damage transport the
expansion module in the original container.
• Verify that all parts shipped with the expansion module.
• Do not drop the expansion module or subject it to
physical shock.
Parts included
• One XPM expansion module with removable terminal
blocks (Input/Output, Power and SA bus terminal
blocks)
• One installation guide sheet
Materials and special tools needed
• Three fasteners appropriate for the mounting surface
(M4 screws or #8 screws)
• One 20 cm (8 in.) or longer piece of 35 mm DIN rail and
appropriate hardware for DIN rail mount (only)
• Small straight-blade (1/8 in. or 3.2 mm) or Philips #2
screwdriver for securing wires in the terminal blocks
Physical features
The following figures display the physical features of XPM
expansion modules, and the accompanying table provides
a description of the physical features and a reference to
further information where required.
*241014302155-*
Part No. 24-10143-02155 Rev -
2020-11-11
(Barcode for factory use only)
F4-XPM04060, F4-XPM09090, F4-XPM18000
Figure 1: XPM09090 and XPM04060 Physical Features
(XPM04060 model shown)
Figure 2: XPM18000 Physical Features
Table 1: Physical features of expansion modules
Physical Feature: Description and References
1Binary Output (BO) Terminal Block: Black terminals. Only
present on XPM09090 and XPM04060 models. See Table 2.
2
Configurable Output (CO) Terminal Block: Black terminals.
Only present on XPM09090 and XPM04060 models. See
Table 2.
4Device Address Rotary Switch Block: Decimal Addressing
See Setting the device address.
5Supply Power Terminal Block: Gray terminals; 24 VAC,
Class 2. See Figure .
6Cover Lift Tab. See Removing the expansion module cover.
7SA/FC Bus Terminal Block: Orange terminal. See .
Table 1: Physical features of expansion modules
Physical Feature: Description and References
8End-of-Line (EOL) Switch. See Setting the End-of-Line
(EOL) switch.
9Binary Input (BI) Terminal Block: White terminals. See
Table 2.
10 Universal Input (UI) Terminal Block: Only present on
XPM09090 and XPM04060 models. See Table 2.
11 Sensor Actuator (SA) Bus/Field Controller (FC) Bus Port
(RJ-12 6-pin Modular Jack). See .
12 LED Status Indicators. See LED status and states.
Note: Analog Output (AO) Terminal Block (Black
terminal) is only present on XPM09090 model. See
Table 2.
Mounting
Observe the following guidelines when mounting an
expansion module:
• Ensure the mounting surface can support the
expansion module, DIN rail, and any user-supplied
enclosure.
• Mount the expansion module horizontally on 35 mm
DIN rail whenever possible.
• Mount the expansion module in the proper mounting
position.
• Mount the expansion module on a hard, even surface
whenever possible in wall-mount applications.
• Use shims or washers to mount the expansion module
securely and evenly on the mounting surface.
• Mount the expansion module in an area free of
corrosive vapors and observe the Ambient Conditions
requirements in Table 12.
• Provide for sufficient space around the expansion
module for cable and wire connections for easy cover
removal and good ventilation through the expansion
module (50 mm [2 in.] minimum on the top, bottom,
and front of the expansion module).
• Do not mount the expansion module on surfaces prone
to vibration, such as duct work.
• Do not mount the expansion module in areas where
electromagnetic emissions from other devices or wiring
can interfere with expansion module communication.
On panel or enclosure mount applications, observe the
following additional guidelines:
• Mount the expansion module so that the enclosure
walls do not obstruct cover removal or ventilation
through the expansion module.
• Mount the expansion module so that the power
transformer and other devices do not radiate excessive
heat to the expansion module.
• Do not install the expansion module in an airtight
enclosure.
F4-XPM Expansion Modules Installation Guide2
Figure 3: Expansion Module mounting position
Mounting features and dimensions
Figure 4: Back of XPM04060 and XPM18000 expansion
module
Figure 5: Back of XPM09090 expansion module
Note:
• Mounting dimensions are listed in millimeters in
the above figures.
• The DIN rail channel and the mounting clips are
shown in an extended position.
DIN rail mount applications
About this task:
To mount a XPM expansion module horizontally on a
35 mm DIN rail (recommended method), complete the
following steps:
1. Securely mount a 20 cm (8 in.) or longer section
of 35 mm DIN rail horizontal and centered in
the desired space so that the expansion module
mounts in the horizontal position.
2. Pull the two bottom mounting clips outward from
the expansion module to the extended position
(Figure 3).
3. Hang the expansion module on the DIN rail by
the hooks at the top of the (DIN rail) channel on
the back of the expansion module (Figure 4), and
position the expansion module snugly against the
DIN rail.
4. Push the bottom mounting clips inward (up) to
secure the expansion module on the DIN rail.
5. To remove the expansion module from the DIN rail,
pull the bottom mounting clips out to the extended
position and carefully lift the expansion module off
the DIN rail.
Wall mount applications
About this task:
To mount a XPM expansion module directly on a wall or
other flat vertical surface, complete the following steps:
1. Pull the two bottom mounting clips outward and
ensure they are locked in the extended position.
2. Determine the proper mounting position the
expansion module will be installed. Mark the
mounting hole locations on the wall using the
dimensions for the expansion module listed in
Mounting features and dimensions. Alternatively,
hold the expansion module up to the wall or
surface in a proper mount position and mark the
hole locations through the mounting clips.
3. Drill holes in the wall or surface at the marked
locations, and insert appropriate wall anchors in the
holes (if necessary).
4. Hold the expansion module in place, and insert
the screws through the mounting clips and into
the holes (or anchors). Carefully tighten all of the
screws.
Important: Do not over-tighten the mounting
screws. Over-tightening the screws may
damage the mounting clips.
Wiring
Observe the following guidelines when wiring an XPM
expansion module:
F4-XPM Expansion Modules Installation Guide 3
CAUTION
Risk of Electric Shock:
Disconnect the power supply before making electrical
connections to avoid electric shock.
ATTENTION
Mise En Garde: Risque de décharge électrique:
Débrancher l'alimentation avant de réaliser tout
raccordement électrique afin d'éviter tout risque de
décharge électrique.
CAUTION
Risk of Property Damage:
Do not apply power to the system before checking
all wiring connections. Short circuited or improperly
connected wires may result in permanent damage to
the equipment.
ATTENTION
Mise En Garde: Risque de dégâts matériels:
Ne pas mettre le système sous tension avant
d'avoir vérifié tous les raccords de câblage. Des
fils formant un court-circuit ou connectés de façon
incorrecte risquent d'endommager irrémédiablement
l'équipement.
Important: Do not exceed the expansion module
electrical ratings. Exceeding the electrical ratings
can result in permanent damage to the expansion
module and void any warranty.
Important: Use copper conductors only. Make
all wiring in accordance with local, national, and
regional regulations.
Important: Electrostatic discharge can damage
expansion module components. Use proper
electrostatic discharge precautions during
installation, setup, and servicing to avoid damaging
the expansion module.
For detailed information about configuring and wiring an
MS/TP Bus, FC bus, and SA bus, refer to the FX-PC Series
Controllers MS/TP Communications Bus Technical Bulletin
(LIT-12011670).
Terminal wiring guidelines, functions,
ratings, and requirements
This section provides further guidelines on input and
output wiring, maximum cable length versus load current,
and SA Bus and supply power wiring.
Input and Output wiring guidelines
I/O terminal block functions, ratings and requirements
provides information and guidelines about the functions,
ratings, and requirements for the controller input and
output terminals, and Table 3 also references guidelines
for determining proper wire sizes and cable lengths.
In addition to the wiring guidelines in I/O terminal block
functions, ratings and requirements, observe these
guidelines when wiring expansion modules inputs and
outputs:
• Run all low-voltage wiring and cables separate from
high-voltage wiring.
• All input and output cables, regardless of wire size or
number of wires, should consist of stranded, insulated,
and twisted copper wires.
• Shielded cable is not required for input or output
cables.
• Shielded cable is recommended for input and output
cables that are exposed to high electromagnetic or
radio frequency noise.
• Inputs/outputs with cables less than 30 m (100 ft)
typically do not require an offset in the software setup.
Cable runs over 30 m (100 ft) may require an offset in
the input/output software setup.
F4-XPM Expansion Modules Installation Guide4
I/O terminal block functions, ratings and requirements
Table 2: I/O terminal block functions, functions, ratings, requirements, and cable guidelines
Terminal Block label Terminal
label Function, ratings, requirements Determine wire size and
maximum cable length
+15 V
15 VDC Power Source for active (3-wire) input devices
connected to the Universal UI-n terminals.
Provides 100 mA total current
Same as (Universal) UI-n
Note: Use 3-wire cable for
devices that source power
from the +15V terminal.
Analog Input - Voltage Mode (0–10 VDC)
10 VDC maximum input voltage
Internal 10k ohm Pull-down
See Guideline A in Table 3
Analog Input - Current Mode (4–20 mA)
Internal 100 ohm load impedance
Note: Current loop jumpers must be in the Enabled
position to maintain a closed 4-20 mA current loop. See
Setting the UI current loop jumpers.
See Guideline B in Table 3.
Analog Input - Resistive Mode (0–600k ohm)
Internal 12 V. 15k ohm pull up
Qualified Sensors: 0-2k ohm potentiometer, RTD (1k Nickel
[Johnson Controls® sensor], 1k Platinum, and A99B Silicon
Temperature Sensor) Negative Temperature Coefficient (NTC)
Sensor
See Guideline A in Table 3.
UI-n
Binary Input - Dry Contact Maintained Mode
1 second minimum pulse width
Internal 12 V. 15k ohm pull up
See Guideline A in Table 3.
UNIVERSAL
(Inputs)
UI-Cn
Universal Input Common for all Universal Input terminals
Note: All Universal UI-Cn terminals share a common,
which is isolated from all other commons.
Same as (Universal) UI-n
Binary Input - Dry Contact Maintained Mode
0.01 second minimum pulse width
Internal 18 V. 3k ohm pull up
BI-nBinary Input - Pulse Counter/Accumulator Mode
0.01 second minimum pulse width
(50 Hz at 50% duty cycle)
Internal 18 V. 3k ohm pull up
BINARY
(Inputs)
BI-Cn
Binary Input Common for all Binary Input terminals
Note: All Binary BI-Cn terminals share a common,
which is isolated from all other commons, except the
Configurable Output (CO) common (CO-Cn) when the
CO is defined as an Analog Output.
See Guideline A in Table 3.
F4-XPM Expansion Modules Installation Guide 5
Table 2: I/O terminal block functions, functions, ratings, requirements, and cable guidelines
Terminal Block label Terminal
label Function, ratings, requirements Determine wire size and
maximum cable length
Analog Output - Voltage Mode (0–10 VDC)
10 VDC maximum output voltage
10 mA maximum output current
Required an external load of 1,000 ohm or more.
See Guideline A in Table 3.
CO-nBinary Output - 24 VAC Triac (External Power Source only)
Connects CO-n to CO-Cn when activated.
External Power Source Requirements:
24 VAC maximum output voltage
0.5 A maximum output current
40 mA minimum load current
See Guideline C in Table 3.
CONFIGURABLE
(Outputs)
CO-Cn
Analog Output Signal Common All Configurable Outputs
(COs) defined as Analog Outputs (AOs) share a common,
which is isolated from all other commons except the Binary
Input common.
Binary Output Signal Common All Configurable Outputs
(COs) defined as Binary Outputs are isolated from all other
commons, including other CO commons.
Same as (Configurable) CO-n.
Analog Output - Voltage Mode (0–10 VDC)
10 VDC maximum output voltage
10 mA maximum output current
Required an external load of 1,000 ohm or more.
Note: The Analog Output (AO) operates in the Voltage
Mode when connected to devices with impedances
greater than 1,000 ohm. Devices that drop below 1,000
ohm may not operate as intended for Voltage Mode
applications.
AO-n
Analog Output - Current Mode (4–20 mA)
Requires and external load between 0 and 300 ohm.
Note: The Analog Output (AO) operates in the Current
Mode when connected to devices with impedances less
than 300 ohm. Devices with impedances greater than
300 may not operate as intended for Current Mode
applications.
ANALOG
(Outputs)
AO-Cn
Analog Output Signal Common for all Analog Output
terminals.
Note: All Analog Output Common terminals (AO-
Cn) share a common, which is isolated from all other
commons.
See Guideline C in Table 3.
BO-n
Binary Output - 24 VAC Triac (External Power Source)
Connects BO-n to BO-Cn when activated.
External Power Source Requirements:
24 VAC maximum output voltage
0.5 A maximum output current
40 mA minimum load current
BINARY
(Output)
BO-Cn
Binary Output Common for all Binary Output terminals.
Note: Each Binary Output Common terminal (BO-Cn) is
isolated from all other commons, including other Binary
Output Common terminals.
See Guideline C in Table 3.
F4-XPM Expansion Modules Installation Guide6
Cable and wire length guidelines
Table 3 defines cable length guidelines for the various wire sizes that may be used for wiring low-voltage (<30 V) input
and outputs. The required wire sizes and lengths for high-voltage (>30 V) Relay Outputs are determined by the load
connected to the relay, and local, national or regional electrical codes.
Table 3: Cable length guidelines
Guideline Wire size/Gauge and type Maximum cable length and
type Assumptions
1.0 mm (18 AWG) stranded copper 457 m (1,500 ft) twisted wire
0.8 mm (20 AWG) stranded copper
297 m (975 ft) twisted wire 297 m (975 ft) twisted wire
0.6 mm (22 AWG) stranded copper
183 m (600 ft) twisted wire 183 m (600 ft) twisted wire
A
0.5mm (24 AWG) stranded copper
107 m (350 ft) twisted wire 107 m (350 ft) twisted wire
100 mV maximum voltage drop
Depending on the cable length
and the connected input or
output device, you may have
to define an offset in the setup
software for the input or output
point.
1.0 mm (18 AWG) stranded copper 229 m (750 ft) twisted wire
0.8 mm (20 AWG) stranded copper
297 m (975 ft) twisted wire 137 m (450 ft) twisted wire
0.6 mm (22 AWG) stranded copper
183 m (600 ft) twisted wire 91 m (300 ft) twisted wire
B
0.5 mm (24 AWG) stranded copper
107 m (350 ft) twisted wire 61 m (200 ft) twisted wire
100 mV maximum voltage drop
Depending on the cable length
and the connected input or
output device, you may have
to define an offset in the setup
software for the input or output
point.
C
See Figure 6 to select wire size/
gauge.
Use stranded copper wire.
See Figure 6 to determine cable
length.
Use twisted wire cable.
N/A
Maximum cable length versus load current
Use the following figure to estimate the maximum cable
length relative to the wire size and the load current (in
mA) when wiring inputs and outputs.
Note: Figure 6 applies to low-voltage (<30 V) inputs
and outputs only.
Figure 6: Maximum wire length for low-voltage (<30 V) Inputs and Outputs by current and wire size
F4-XPM Expansion Modules Installation Guide 7
Communications bus and supply power
wiring guidelines
Table 4 provides information about the functions, ratings,
and requirements for the communication bus and supply
power terminals. The table also provides guidelines for
wire sizes, cable types, and cable lengths for wiring the
expansion module's communication bus and supply
power.
In addition to the guidelines in Table 4, observe the
following guidelines when wiring an FC bus, SA bus, or the
24 VAC supply power:
• Run all low-voltage wiring and cables separate from
high-voltage wiring.
• All SA and FC bus cables, regardless of wire size, should
be twisted, insulated, stranded copper wire.
• Shielded cable is strongly recommended for all SA and
FC bus cables.
• Refer to the FX-PC Series Controllers MS/TP
Communications Bus Technical Bulletin (LIT-12011670)
for detailed information regarding wire size and cable
length requirements for SA buses.
Table 4: Communications bus and supply power terminal block functions, ratings, requirements, and cable
guidelines
Terminal block/
Port label
Terminal
labels Function, electrical ratings/Requirements Recommended cable type
+
-FC or SA Bus Communications
COM Signal Reference (Common) for FC or SA Bus
communications
FC BUS
or
SA BUS SHD
or
PWR
SHD on FC Bus: Isolated terminal (optional shield drain
connection
PWR on SA Bus: 15 VDC power lead connection.
(Maximum total current draw for SA bus is 240 mA.)
FC Bus: 0.6 mm (22 AWG) stranded,
3-wire twisted, shielded cable
recommended.
SA Bus: 0.6 mm (22 AWG) stranded, 4-
wire (2 twisted-pairs), shielded cable
recommended.
Note: On the SA Bus, the + and
- wire are one twisted pair, and
the COM and PWR are the second
twisted pair of wires.
SA/FC BUS
(Port)
RJ-12 6-Position Modular Connector provides:
• FC or SA Bus Communications
• FC or SA Bus Signal Reference and 15 VDC
Common
24 AWG 3-pair CAT 3 Cable <30.5 m (100
ft)
HOT 24 VAC Power Supply - Hot
Supplies 20–30 VAC (Nominal 24 VAC)
24V~
COM
24 VAC Power Supply - Common
(Isolated from all other Common terminals on
controller.)
0.8 mm to 1.0 mm
(18 AWG) 2-wire
Note: See Table 1 to determine wire size and cable
lengths for cables.
Note: The SA Bus and FC Bus wiring
recommendations in this table are for MS/TP
bus communications at 38,400 baud. For more
information, refer to the FX-PC Series Controllers
MS/TP Communications Bus Technical Bulletin
(LIT-12011670)..
F4-XPM Expansion Modules Installation Guide8
Termination diagrams
A set of Johnson Controls termination diagrams provides details for wiring inputs and outputs to the expansion modules.
See the figures in this section for the applicable termination diagrams.
Note: References to the analog output apply to the XPM09090 model only.
Table 5: Termination details
Type of field
device
Type of Input/
Output Termination diagrams
Temperature
Sensor UI
Voltage Input -
External Source UI
Voltage Input -
Internal Source UI
Voltage Input
(Self-Powered) UI
F4-XPM Expansion Modules Installation Guide 9
Table 5: Termination details
Type of field
device
Type of Input/
Output Termination diagrams
Current Input -
External Source
(Isolated)
UI
Current Input -
Internal Source (2-
wire)
UI
Current Input -
Internal Source (3
wire)
UI
Current Input -
External Source (in
Loop)
UI
Feedback from
EPP-1000 UI
F4-XPM Expansion Modules Installation Guide10
Ce manuel convient aux modèles suivants
6
Table des matières
Autres manuels Johnson Controls Unité de contrôle
Johnson Controls
Johnson Controls S300 Series Instructions de montage
Johnson Controls
Johnson Controls VP140 L Series Manuel utilisateur
Johnson Controls
Johnson Controls S300 Series Instructions de montage
Johnson Controls
Johnson Controls M4-XPM Manuel utilisateur
Johnson Controls
Johnson Controls Mercury 3 Series Manuel
Johnson Controls
Johnson Controls System 350 Y350R Manuel de service
Johnson Controls
Johnson Controls System 350 Manuel de service
Johnson Controls
Johnson Controls Tyco PRV-1A Manuel utilisateur
Johnson Controls
Johnson Controls VG8000V Series Manuel utilisateur
Johnson Controls
Johnson Controls G77 Series Manuel de service
Johnson Controls
Johnson Controls M300CJ Manuel utilisateur
Johnson Controls
Johnson Controls M300CJ-R Manuel utilisateur
Johnson Controls
Johnson Controls P352PN-2 Manuel utilisateur
Johnson Controls
Johnson Controls Facility Explorer FX20 Manuel utilisateur
Johnson Controls
Johnson Controls Penn System 350 S350P Manuel utilisateur
Johnson Controls
Johnson Controls V46SA Series Manuel utilisateur
Johnson Controls
Johnson Controls System 450 Series Manuel utilisateur
Johnson Controls
Johnson Controls Tyco DV-5a Series Manuel utilisateur
Johnson Controls
Johnson Controls Tyco DV-5a Series Manuel utilisateur
Johnson Controls
Johnson Controls VF Series Manuel utilisateur
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
