IWILL PIINS Manuel utilisateur

EC Declaration of Conformity

Iwill Corp.

No. 9-1, Kong 6th RD.,

Lin Kou 2nd Industrial

Park, Taipei, Taiwan R.O.C.

declare under sole responsibility that the

PIINS motherboard

meets the intent of Directive 89/336/ECC for Electromagnetic Compatibility.

Compliance was demonstrated to the following specifications as listed in the

official Journal of the European Communities:

EN 50081-1 Emissions:

EN 55022 Radiated, Class B

EN 55022 Conducted, Class B

EN 60555-2 Power Harmonics

EN 50082-1 Immunity:

IEC 801-2 Electrostatic Discharge

IEC 801-3 RF Radiat

IEC 801-4 Fast Transient

About This Manual

This manual will guide the user how this SCSI motherboard was consisted. All

useful information will be described in later chapters. Keep this manual for your

futureupgradeor system configuration changed.

The chapter Quick Installation ---

This cha pter’s description is suitable for most user, Just follow step by step in

installing the system.

The chapter Overview ---

Describe the feature and specificaton of this SCSI motherboard.

The chapter Manufacture Default ---

This SCSI motherboard has pre-setting before ship out and this pre-setting default

is suitable for most user.

The Hardware Installation ---

Describes the hardware detailspecification and connection.

The ATX Form-Factor Overview ---

The ATX is the new generation form-factor.

The Award BIOS Setup ---

Detail description of this SCSI motherboard, no need to change the manufacture

default unless you have conflict in yoursystem.

The SCSI BIOS Setup ---

The Adaptec SCSI BIOS setup.

Trademark

Intel / Pentium is trademark of Intel Corporationand all other product namesaretrademarksand

registered trademarksof their respective owners.

Warning

This motherboardis carefully designedwith Intelspec.to fullysupportP54Cprocessor upto 200Mhz

and the new P55C. Since Intel is not shipingthe new P55CCPU with 200Mhz atthe point that we

deliver this motherboard sowe hold the responsibilityon if Intel change anyspec.that causethe new

processor notfunctionproperlyin thismotherboard.

Contents

Chapter 0- Quick Installation P4

Chapter 1- Overview P14

1.1 Features P14

1.2 Specifications P16

Chapter 2- Quick Installation P17

Chapter 3- Hardware Installation P18

3.1 Preparation and Inspection P18

3.2 Placement P19

3.3 CPU group P21

3.4 Cache Memory P24

3.5 D-RAM Configuration P24

3.6 SCSI Interface P27

3.7 RAIDBUS P31

3.8 IDE Interface P31

3.9 USB P32

3.10 Enhanced Multi-IO P33

3.11 Other P34

Chapter 4- ATX Form-Factor Overview P37

Chapter 5- Award BIOS Setup P40

5.1 Entering Setup P43

5.2 Standard CMOS Setup P46

5.3 BIOS Features Setup P50

5.4 Chipset Feature Setup P55

5.5 Power Management Setup P62

5.6 PNP/PCI Configuration P66

5.7 Integrated Peripherals P69

5.8 Load Setup Defaults P71

5.9 Supervisor/User Password P72

5.10 IDE HDD Auto Detection P73

5.11 HDD Low Level Format P73

5.12 Save & Exit Setup P73

5.13 ExitWithout Saving P73

Chapter 6- SCSI BIOS Setup P74

6.1 When to Use the SCSI Select Utility P74

6.2 SCSI Select Utility option P75

6.3 Configure / View Host AdapterSettings Menu P76

6.4 SCSI Disk Utilities P81

CHAPTER0

Quick Installation

Several easy installation steps will be described in this chapter to help the

experienced users for quick installation. If you are new user and need to know

more about this motherboard, please start from Chapter 1.

JP18

P.Control

PCI#1

PCI#2

PCI#3

PCI#4

ISA

RAID

BIOS

Bank 0

Bank 1

Bank 2

Bank 3

P. IDE

S. IDE

FDC

U. SCSI

W. SCSI

ATX P.

USB

PS2

LPT

Fan

Slot 1 Connector

Figure 1:Connectors for PIINS

JP7

JP16

JP19

JP4

JP5

J24

Figure 3 : Jumpers location

Connector Function Description

ATX P. 20 pin Standard ATX power input connector

BIOS BIOS (Basic Input Output System)

Bank 0 SIMM Socket(Single In-line Memory Module ) J15, J16

Bank 1 SIMM Socket(Single In-line Memory Module ) J14, J9

Bank 2 SIMM Socket(Single In-line Memory Module ) J8, J7

Bank 3 SIMM Socket(Single In-line Memory Module ) J6, J5

Slot1 Processor Retention Mechanism

FDD 34 pin Floppy Disk Drive with key protect connector

LPT 25 pin Parallel D-Sub connector

IR 6 pin pin-header connector

ISA 4 x ISA(Industrial Standard Architecture) 98 pin expansion slot

FAN JP1 Fan Power connector

JP18 Remote Power On/Off connector

KB 6 pin PS2 keyboard Mini-DIN connector

P. IDE40 pin Primary IDE with key protect connector

PCI 3 x PCI version 2.1 compliance 120 pin PCI (Peripheral

Component Interface)expansion slot

RAIDBUS 60 pin extension slot for working with RAIDBUS 1130 adapter

P. Control Front panel signal control connector

RST—Reset Switch

SCSI—SCSI detect LED

IDE—IDE detect LED

SMI—System Management Interface switch

LED—Power-on LED

Speaker—Speaker connector

Keylock—Keylock switch connector

PS2 6 pin PS2 mouse Mini-DIN connector

S. IDE 40 pin Secondary IDE with key protect connector

S1 9 pin Serial 1 D-Sub connector

S2 9 pin Serial 2 D-Sub connector

U. SCSI 50 pin Ultra SCSI with key protect connector

USB Two 4 pin Universal Serial Bus connector for USBA & USBB

W. SCSI 68 pin Wide SCSI with key protect connector

Jumper Setting

JP4 CMOS Normal/Clear select

JP5 Auto Terminator select

JP7 SCSI Enabled/Disabled select

JP PCI#3&4

JP16 Modem Ring-In Enabled

J24 Diamond VGA Enabled

Quick Installation

Step 1. Install CPU card

Follow following to screw theProcessor Rentention Mechanism.

There are two sets of the Thread Studs need to screw to the Slot1’s

Processor Retention Mechanism by a criss-cross screw driver.

Plug theSlot1 CPU card into the Slot1 Rentention Mechanism in

horizontaldirection down to make sure that were contact correctly.

JP1

Step 2. Install CPU Cooler’s power

Hook the CPU Cooler’s power cable to JP1 that marked “FAN”.

Step 4. Adjust the CPU frequency

With the special design on this motherboard.Once the jumper

cap was inserted, it will automatically caculate the Internal/

External Clock and CLKMUL (Clock Multiplier). Just insert

the jumpercap to the CPU real frequency.

JP7

JP16

JP19

JP4

JP5

JP19

300

233

240

266

270

Step 5. Install the Memory Module

For at least two pieces 72 pin SIMM(Single In-line Memory

Module) must inserted in this 64 bit motherboard.

The J15/J16 were combined as Bank0,J9/J14 were combined as Bank1,

J7/J8 were as Bank2,J5/J6 were combined as Bank3.Any Bank can be

powered on by thesame pair (two pieces) of SIMM memorymodule.The

maximum capacity of thismotherboard is 1024 MByte.

Bank 0

Bank 1

Bank 2

Bank 3

Bank 0

Bank 1

Bank 2

Bank 3

J16

J15

J14

Step 6. Install the Internal Peripherals

The internal peripherals meansdevicesthat in the computer

chassis like the Floppy Disk Drive, HardDisk Drive, CD ROM

Drive …etc. With this motherboard package, there are 34, 40,

50 and 68 pin flat cable. Use these cables to connect the

motherboard and internal devices. All flat cable’s connectorhousing

have the key protect,this will guide you the correct direction

when you insert.

Step 7. Install the External Peripherals

The externaldevice meansdevicesthat outsidethe computer

chassis like the Serial mouse,Printer, PS/2 Mouse, External

Modem…etc. With this motherboa rd’s package there are two

10 pin cables convertto 9 and 25 pin D-Sub maleconnector

cable are for Serial port, one26 pin convert to 25 pin D-Sub

femaleconnectorcable is for Parallel port, one 5 pin housing

but 4 wires into a 6 pin Mini-DIN is for the PS/2 mouse.

Step 8. Install the SMI(System Management Interrupt)

Table des matières

Autres manuels IWILL Carte mère

IWILL

IWILL DK8X Manuel utilisateur

IWILL

IWILL DP533 Series Manuel utilisateur

IWILL

IWILL P4DA Manuel utilisateur

IWILL

IWILL P4G Series Manuel utilisateur

IWILL

IWILL P55TV Manuel utilisateur

IWILL

IWILL IWILL P4D-N Manuel utilisateur

IWILL

IWILL DVD266 Manuel utilisateur

IWILL

IWILL DP400 Manuel utilisateur

IWILL

IWILL VD133 Manuel utilisateur

IWILL

IWILL P4GB Series Manuel utilisateur

IWILL

IWILL mP4G2 Series Manuel utilisateur

IWILL

IWILL LE370 Manuel utilisateur

IWILL

IWILL DPIILS2 Manuel utilisateur

IWILL

IWILL P4SP Manuel utilisateur

IWILL

IWILL K7S3 Series Manuel utilisateur

IWILL

IWILL VX133 Manuel utilisateur

IWILL

IWILL P55TU Manuel utilisateur

IWILL

IWILL Motherboard DJ800 Manuel utilisateur

IWILL

IWILL MPX2 Manuel utilisateur

IWILL

IWILL DN800 Manuel utilisateur

IWILL

IWILL P55XU Manuel utilisateur

IWILL

IWILL P55TV Manuel utilisateur

IWILL

IWILL DGL200 Manuel utilisateur

IWILL

IWILL BS100 Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur