Ipf electronic UT139570 Manuel utilisateur

MANUAL • Subject to alteration! Version: June 2022

ipf electronic gmbh

│

Rosmarter Allee 14 • 58762 Altena • Germany

│

Tel +49 2351 9365-0 • info@ipf-electronic.com •

www.ipf-electronic.com

UT139570

Ultrasonic sensor

Diffuse-reflection sensor

ISetting via teach-in

I3 different teach modes

IPush-pull switching output

IM8-connector

TECHNICAL DATA

Scanning range 20 … 200mm

Operating voltage U

18 … 30V DC

Analog output

Push-pull, no/nc switchable

Output current (max. load) 150mA

Short-circuit proof

Reverse polarity protected

Voltage drop

2.0V DC

Switching frequency

20Hz

Current consumption (without load) 40mA

Standard measuring plate

100 x 100mm

Resolution

1mm

Repeatability

0.5mm

Hysteresis

2 … 20mm (adjustable via IO-Link)

Mounting distance (sensor to sensor)

60mm

Setting

Teach-in

Carrier frequency

400kHz

Protection class

III

Insulation dielectric strength

500V

Protection class (EN 60529)

IP 67

Material (housing)

Brass nickel plated

Temperature (operation)

-25 … +70°C

Temperature drift

0.2%/K (uncompensated)

Connection

M8-connector 4-pin

Connection accessories

e.g. VK200375

Connection Dimensional

drawing

IO-Link interface

Normally open contact / normally closed contact switchable

brown

white

Teach-in / lock

black

Push-pull NO / NC switchable

blue

*Sound outlet

MANUAL • Subject to alteration! Version: June 2022

ipf electronic gmbh

│

Rosmarter Allee 14 • 58762 Altena • Germany

│

Tel +49 2351 9365-0 • info@ipf-electronic.com •

www.ipf-electronic.com

Proper use

Ultrasonic diffuse-reflection sensor are used as part of a higher-level overall system for the contactless detection of objects.

Function

Ultrasonic diffuse-reflection sensors work on the principle of time-of-flight measurement. The device transmits a pulse

sequence, which is then reflected by an object. The device detects the reflected wave and measures the time that has

elapsed between the transmission and reception processes. This time is used to determine the distance between the sensor

and the object. If the results correspond to the specified values, the switching output is set accordingly.

Mounting

The sensor may be mounted in any position. Make sure that it is mounted in a vibration-free and vibration-damping manner.

Also protect the device against mechanical loads such as shocks or impacts.

The transducer surface and the area of the detection lobe must be kept free. Make sure that there are no interfering objects

between the sensor and the target object inside the lobe. Otherwise, it is possible that the interfering object will cause

faulty switching. Also, avoid positioning two or more ultrasonic sensors opposite each other.

Temperature

The speed of sound in air depends on the temperature. Operation outside the specified ambient temperature is not

allowed. A temperature compensation can be switched on via IO-Link.

When temperature compensation is activated, the sensor requires about 15 minutes of warm-up time after a cold start;

only then are the measured values reproducible.

Transmission angle of the object in diffuse mode

Objects with a smooth surface are scanned reliably up to an angle of

inclination of approx. 10°. The maximum permissible tilting angle

increases for objects with a rough or heavily structured (grained)

surface.

Blindbereich im Tastbetrieb

The range 0 … 20mm in front of the sensor corresponds to the ultrasonic typical blind

range.

Distance measurements are not possible in the blind range!

The maximum scanning distance 200 mm.

Operation as a reflex barrier can be selected via IO-Link. To do this, set the value 1 to the desired distance from the reference

surface. The selected distance may vary by about 5mm. All objects that interrupt the sound between the sensor and the

reference surface are detected. The blind area may be disregarded in this case.

Detection beams

Plate 100 x 100mm

- - - - - - Round bar Ø 10mm

MANUAL • Subject to alteration! Version: June 2022

ipf electronic gmbh

│

Rosmarter Allee 14 • 58762 Altena • Germany

│

Tel +49 2351 9365-0 • info@ipf-electronic.com •

www.ipf-electronic.com

Cleaning

For cleaning a soft cloth moistened with soapy water is recommended.

Commissioning and adjustment

The measuring range is taught-in and the analog output is switched over by connecting the black wire (PIN 2) to the

operating voltage (PIN1).

The teach process is aborted after 20 seconds (Time Out function).

Make sure that the object to be detected is always within the scanning range limits (20 … 200mm).

In normal operation, connect the teach line to 0V to avoid interference.

1. Teach-in of a switching window

1. position the object at the switching limit 1.

2. Connect the white wire to the operating voltage for between 0.1 and 2 seconds. The LED flashes with approx.

1Hz.

3. position the object at the switching limit 2.

4. connect the white wire to the operating voltage for between 0.1 and 2 seconds.

5. the switching output is active at a distance between switching limit 1 and switching limit 2.

2. Teach-in of an object with background suppression (2-point teach)

1. position the object at the desired position.

2. connect the white wire to the operating voltage for between 2 and 4 seconds. The LED flashes with approx.

1Hz.

3. take the object out of the detection lobe so that the sensor is aligned with the background.

4. connect the white wire to the operating voltage for between 0.1 and 2 seconds.

5. the switching threshold is centered between object and background.

3. Automatic teach-in (Auto-Teach)

1. align the sensor with the background.

2. connect the white wire to the operating voltage for between 4 and 6 seconds. The LED flashes with approx.

2Hz.

3. in the next 4 to 8 seconds, guide as many objects as possible past the sensor at the desired distance.

4. the switching threshold is between object and background.

4. Change switching function (no / nc)

1. connect the white wire to the operating voltage for more than 6 seconds.

2. the switching output now works with the inverted function.

5. LED display after each teach process

If the status LED flashes twice, the teach process was successful and the sensor operates with the new values.

If the status LED flashes four times, the teach process has been aborted or the time window of 20 seconds has

been exceeded. The sensor operates with maximum switching distance as a normally open contact.

On the following page the descriptions are shown again graphically.

MANUAL • Subject to alteration! Version: June 2022

ipf electronic gmbh

│

Rosmarter Allee 14 • 58762 Altena • Germany

│

Tel +49 2351 9365-0 • info@ipf-electronic.com •

www.ipf-electronic.com

1. Teach-in of a switching window

2. Teach-in of an object with

background suppression (2-

point teach)

3. Automatic teach-in (Auto-

Teach)

4. Change switching function

5. LED display after each teach

process

Note: Resetting to the factory setting is only possible via IO-Link

SAFETY INSTRUCTIONS:

Before commissioning, please make sure that all safety instructions listed in the product documentation, if applicable,

have been observed!

In case of direct impact on personal safety, the use of these products is prohibited.

Autres manuels ipf electronic Accessoires

ipf electronic

ipf electronic OT450521 Manuel utilisateur

ipf electronic

ipf electronic UT300027 Manuel utilisateur

ipf electronic

ipf electronic OTQ90170 Manuel utilisateur

ipf electronic

ipf electronic MW10015 Series Manuel utilisateur

ipf electronic

ipf electronic OT0591A4 Manuel utilisateur

ipf electronic

ipf electronic OR150400 Manuel utilisateur

ipf electronic

ipf electronic UT189020 Manuel utilisateur

ipf electronic

ipf electronic UT30C310 Manuel utilisateur

ipf electronic

ipf electronic DW35312 Series Manuel utilisateur

ipf electronic

ipf electronic IV56E205-S Manuel utilisateur

ipf electronic

ipf electronic UT189023 Manuel utilisateur

ipf electronic

ipf electronic UT139073 Manuel utilisateur

ipf electronic

ipf electronic OTR49174 Manuel utilisateur

ipf electronic

ipf electronic OTQ80576 Manuel utilisateur

ipf electronic

ipf electronic OT05E244 Manuel utilisateur

ipf electronic

ipf electronic opti-check OC5396 Series Manuel utilisateur

ipf electronic

ipf electronic UT990934 Manuel utilisateur

ipf electronic

ipf electronic OTR49170 Manuel utilisateur

ipf electronic

ipf electronic PRQ80376 Manuel utilisateur

ipf electronic

ipf electronic PY740020 Manuel utilisateur

ipf electronic

ipf electronic ON430570 Manuel utilisateur

ipf electronic

ipf electronic OS15 Series Manuel utilisateur

ipf electronic

ipf electronic UT360321 Manuel utilisateur

ipf electronic

ipf electronic OTR49175 Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur

ipf electronic UT139570 Manuel utilisateur

Manuels Accessoires populaires d'autres marques