Ipf electronic ON430571 Manuel utilisateur

operating distance 800mm

robust plastic housing, compact design

for detecting transparent objects

Teach in-based setting

LED display for fine adjustment

reduction in the level of reciprocal optical interference

connection with 4-pin M8-connector

Technica datal

version transparent objects recognition (trays / bottles)

background position (Sde) 200 … 800mm on shiny metallic surfaces

detection range (Sa) 100% of Sde

operating voltage UB 10 … 30V DC

current consumption (w/o load) ≤ 35mA

output current (max. load) ≤ 100mA

output signal push-pull, no/nc

voltage drop (max. load) ≤ 2V DC

reaction- /decay time ≤ 1.8msec

sampling frequency ≤ 270Hz

short-circut protection +

reverse polarity protection +

display (signal) green LED

display (status) / setting control red LED

transmitting element red LED, 660nm, pulsed

light spot size

housing material

front screen material

system of protection

Ø15mm at 800mm

plastic (ASA-MABS)

PMMA

IP67 (EN 60529)

operating temperature -30°C … +60°C

connection

max. tightening torque

M8-connector, 4-pin

0.8Nm

description:

These completely new through-beam sensors work according to the principle established with the retro-reflective

sensor. With these devices however, no retro-reflector is used. Any flat surface can be used as a reflector, e.g. the wall

of a piece of machinery.

This is `teached in' as a background item, via the Teach-In line (white wire, PIN 2). Each object that is located between

the sensor and background position is detected. This induces a change to the signal at the switch output. The system

also detects transparent objects. The position and characteristics of the background should not change whilst the

device is in operation. In the case of metallic shiny surfaces, the maximum ran-ge is 800mm. In the case of other

materials, the operating distance is reduced!

new: works like a retro-reflective

sensor - but without a reflector

ON430571

MANUAL •Subject to alteration! Version: May 2016

ipf electronic gmbh

•Rosmarter Allee 14 •58762 Altena

│

Tel +49 2351 9365-0 •Fax +49 2351 9365-19

│

[email protected] •www.ipf-electronic.com 1

the teach-in procedure relating to through-beam sensor operation:

1. Align the sensor towards a reflective part of the machinery.

2. Connect the Teach-In line (white, PIN 2) for longer than 2 seconds (however less than 5 seconds) with +UB. The red LED will

flash.

3. Connect the Teach-In line again for a short period with +UB.

4. If the sensor is intended to work as a break contact (output switched if an object is detected), then connect the Teach-In

line again for a short period with +UB. Otherwise the device works as a make contact.

5. In the case of soiling and temperature effects, the switching threshold is only corrected if the path of light to the re-flecting

machinery part is free from obstructions.

notes: The above status information applies to a „plus switching“ (pnp) connection. For a „minus switching“ (npn)

connection the status information has to be inverted.

In the teach mode, the output changes over to 0V.

Under normal operations, the Teach-In line must be grounded (0V)!

If the sensor is `teached in' outside of its detection range, or if the quality of the signal is insufficient, a warning signal

will be displayed (rapid flashing of the red LED). The sensor will then retain its previous setting.

If there is a short circuit at the switching output, the red LED will flash approx. once a second.

alignment mark

Connect the teach-line to +UB for more than 10 seconds. The red LED flashes rapidly.

Break the connection. If the red LED light now goes out, this means that the signal quality is insufficient, or the sensor is outside the

detection range. No teach in is possible. In the case of a flashing LED, the signal quality is good. The sensor can now be teached.

In order to return to the normal mode, connect the Teach-In line for a short period to +UB.

electric connection dimension drawing

suitable cable socket: e.g. VK200375

Warning: Never use these devices in applications where the safety of a person depends on their

functionality.

* transmitter axis

wire colors: bn = brown (1), wh = white (2), bu = blue (4), bk =

black (4)

Teach-in-input

switching output

MANUAL •Subject to alteration! Version: May 2016

ipf electronic gmbh

•Rosmarter Allee 14 •58762 Altena

│

Tel +49 2351 9365-0 •Fax +49 2351 9365-19

│

[email protected] •www.ipf-electronic.com 2

Autres manuels ipf electronic Accessoires

ipf electronic

ipf electronic UT300027 Manuel utilisateur

ipf electronic

ipf electronic ON330571 Manuel utilisateur

ipf electronic

ipf electronic DW34311 Series Manuel utilisateur

ipf electronic

ipf electronic MW10015 Series Manuel utilisateur

ipf electronic

ipf electronic UT300025 Manuel utilisateur

ipf electronic

ipf electronic OT330571 Manuel utilisateur

ipf electronic

ipf electronic OTR49175 Manuel utilisateur

ipf electronic

ipf electronic OT0591A4 Manuel utilisateur

ipf electronic

ipf electronic UT139073 Manuel utilisateur

ipf electronic

ipf electronic PT230020 Manuel utilisateur

ipf electronic

ipf electronic RO570900 Manuel utilisateur

ipf electronic

ipf electronic UT309023 Manuel utilisateur

ipf electronic

ipf electronic OTR49176 Manuel utilisateur

ipf electronic

ipf electronic OTQ80576 Manuel utilisateur

ipf electronic

ipf electronic OTR49174 Manuel utilisateur

ipf electronic

ipf electronic OR150400 Manuel utilisateur

ipf electronic

ipf electronic OT059176 Manuel utilisateur

ipf electronic

ipf electronic DW34312 Series Manuel utilisateur

ipf electronic

ipf electronic UT990934 Manuel utilisateur

ipf electronic

ipf electronic OTQ90170 Manuel utilisateur

ipf electronic

ipf electronic opti-check OC5396 Series Manuel utilisateur

ipf electronic

ipf electronic OS15 Series Manuel utilisateur

ipf electronic

ipf electronic PRQ80376 Manuel utilisateur

ipf electronic

ipf electronic DW35312 Series Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur

ipf electronic ON430571 Manuel utilisateur

Manuels Accessoires populaires d'autres marques