Invacare Fixed Released Rail/Cane Clamps Manuel utilisateur

PROCEDURE 1 - INSTALLING

CLAMPS ON SEATING SYSTEMS

WITH A GROWTH BRACKET

Twist Release Clamps For Back (FIGURE 1)

NOTE: Refer to INSTALLATION WARNING in the

SAFETY SUMMARY before proceeding.

1. Make sure that the back mounting hooks are flush

against the back canes.

2. Loosensocketscrewthatopenstwistreleaseclamp.

NOTE:Thereisarightandlefttwistreleaseclamp.Make

sure when installing that the socket screw adjustment is

on the outside of the wheelchair frame.

3. Install the open end of the twist release clamp below

the back mounting hook so that the locking mecha-

nism rests on top of the back mounting hook.

4. Loosely tighten the socket screw.

5. Repeat STEPS 1- 4 for the other side.

6. Makesurebothtwistreleaseclampsareflushagainst

thebackmountinghooksandthatthelockingmecha-

nism rests on top of the back mounting hooks.

7. Torque socket screw to 75 - inch pounds.

8. Oncetwistreleasemountingclampsaresecured,do

one (1) of following:

A. Refer to QUICK RELEASE CLAMPS FOR

SEATinPROCEDURE1ofthisinstructionsheet.

B. RefertoUSINGCLAMPSinthisinstructionsheet.

NOTE:CheckALLpartsforshippingdamagebeforeuse.

Incaseofdamage,DONOTuse.ContactCarrier/Dealer

forfurther instruction.

SAFETYSUMMARY

The following recommendations are made for the safe

installationanduseofmountinghardwareonseatingsys-

tems:

GENERAL WARNINGS

DO NOT install this equipment without first read-

ingandunderstandingthisinstructionsheet.Ifyou

areunabletounderstandtheseinstructions,con-

tact a healthcare professional, dealer or techni-

calpersonnel if applicablebefore attemptingto

install this equipment - otherwise, injury or dam-

age may occur.

Ensure that the seat and back of the seating sys-

tem are fixed to the wheelchair. A loose seat or

back may lead to potentially dangerous situa-

tions with positioning devices.

INSTALLATION WARNINGS

DO NOT install twist, quick, and fixed release

clamps in any other locations than specified in

this instruction sheet - otherwise, the seating sys-

tem will not be secured properly to the wheel-

chair and bodily injury may occur.

Ensure that ALL hardware is tight at ALL times.

HARDWARE REFERENCE CHART

NOTE:Thischartisageneralguidelineforrecommended

mountinghardware.

HARDWARE CLAMPS

With Without

Growth Bracket Growth Bracket

BACK Twist Release Twist Release

(SEE FIGURE 1) FixedRelease

(SEE FIGURE 3)

SEAT Quick Release Quick Release

(SEE FIGURE 2) FixedRelease

(SEE FIGURE 4)

Twist Release

Cane Clamp

Inside

Back Cane Back

Mounting

Hook

Socket Screw

Locking Mechanism

FIGURE 1- TWIST RELEASE CLAMPS FOR BACK

Seat Rail

Twist Release Cane Clamps

Quick Release Rail Clamps

Fixed Released Rail/Cane Clamps

Assembly, Installation and Operating Instructions

PROCEDURE 2 - INSTALLING

CLAMPS ON SEATING SYSTEMS

WITHOUT A GROWTH BRACKET

Twist Release Clamps For Back (FIGURE 1)

NOTE: Refer to INSTALLATION WARNING in the

SAFETY SUMMARY before proceeding.

1. Make sure that the back mounting hooks are flush

against the back canes.

2. Loosensocketscrewthatopenstwistrelease clamp.

NOTE: There is a right and left twist release clamp. Make

surewheninstallingthatthesocketscrewadjustmentison

theoutsideofthewheelchairframe.

3. Install the open end of the twist release clamp below

the back mounting hook so that the locking mecha-

nism rests on top of the mounting hook.

4. Loosely tighten the socket screw.

5. Repeat STEPS 1- 4 for the other side.

6. Makesurebothtwist releaseclamps areflush against

thebackmountinghooksandthatthelockingmecha-

nism rests on top of the back mounting hooks.

7. Torque socket screw to 75 - inch pounds.

8. Once twist release mounting clamps are secured, do

one(1)offollowing:

A. RefertoFIXEDRELEASECLAMPSFOR BACK

in PROCEDURE 2 of this instruction sheet.

B. RefertoUSINGCLAMPSinthisinstruction sheet.

Fixed Release Clamps For Back (FIGURE 3)

NOTE: Refer to INSTALLATION WARNING in the

SAFETY SUMMARY before proceeding.

NOTE:Thefixedreleaserail/caneclampsaredesignedto

fiteither1-inchrailtubingor,withinsertprovided,7/8-inchrail

tubing.

1. Remove the mounting screw, lock washer, and inter-

nal threaded mounting screw from the fixed release

clamps (DETAIL “B”).

2. Place the fixed release clamp on the back cane.

3. If fixed release clamp is not tightly fitted around back

cane tubing, install insert provided as shown in DE-

TAIL“A”.

4. Install the fixed release clamp onto the back rail so

thatthefixedportion is flush against and rests on top

ofthemountinghookandislocatedbetweentheseat

railand thebottomof themountinghook.

FIGURE 2 - QUICK RELEASE CLAMPS FOR SEAT

Lock Washer Internal

Mounting

Screw

Quick Release

Rail Clamp

Mounting

Hook

Back Cane

Fixed

Portion Release

Portion

Insert

DETAIL “A”

Quick Release Clamps For Seat (FIGURE 2)

NOTE: Refer to INSTALLATION WARNING in the

SAFETY SUMMARY before proceeding.

NOTE: The quick release clamps are designed to fit

either1-inchrailtubingor,withinsertprovided,7/8-inchrail

tubing.

1. Removethesleeve,lockwasher,and internalthreaded

mounting screw from the quick release clamp (DE-

TAIL“A”).

2. Place the quick release clamp onthe seat rail.

3. Ifquickreleaseclampisnottightlyfittedaroundseatrail

tubing,installinsertprovidedasshowninDETAIL“A”.

4. Install the quick release clamp onto the seat rail so

thatthefixedportionisflushagainstandrestsontopof

themountinghookandthereleaseportionisbetween

thefrontriggingsandthemountinghook.

5. Reinstall the sleeve, lock washer, and internal mount-

ing screw into the quick release rail clamp and torque

to75 - inch pounds.

6. Repeat STEPS 1- 5 for other side.

7. Once quick release mounting clamps are secured,

doone(1)offollowing:

A. RefertoTWISTRELEASECLAMPSFORBACK

in PROCEDURE 1 of this instruction sheet.

B. RefertoUSINGCLAMPSinthisinstructionsheet.

Sleeve

FIGURE 3- FIXED RELEASE CLAMPS FOR BACK

DETAIL “B”

Lock Washer

Sleeve

Mounting

Hook

Internal Mounting

Screw

Twist Release

Clamp

Fixed Release

Clamp

Mounting

Hooks

Seat Rail

Back Cane

Fixed

Portion

Inside of Back Cane

4. Install the quick release clamp onto the seat rail so

thatthefixedportionisflushagainstandrestsontopof

themountinghookandthereleaseportionisbetween

thefrontriggingsandthemountinghook.

5. Reinstall the sleeve, lock washer, and internal mount-

ing screw into the quick release clamp and torque to

75-inchpounds.

6. Repeat STEPS 1- 5 for other side.

7. Oncequickreleasemountingclampsaresecured,do

one(1)offollowing:

A. RefertoFIXEDRELEASECLAMPSFORSEATin

PROCEDURE 2 of this instruction sheet.

B. RefertoUSINGCLAMPSinthisinstruction sheet.

Fixed Release Clamps For Seat (FIGURE 4)

NOTE: Refer to INSTALLATION WARNING in the

SAFETY SUMMARY before proceeding.

NOTE: The quick release and fixed release clamps are

designed to fit either 1-inch rail tubing or, with insert pro-

vided,7/8-inchrailtubing.

1. Removethesleeve,lockwasher,and internalthreaded

mounting screw from the fixed release clamp (DE-

TAIL “C”).

2. Placethefixedreleaseclamp on the seatrail.

3. Iffixedreleaseclampisnottightlyfittedaroundseatrail

tubing,installinsertprovidedasshowninDETAIL“C”.

4. Install the fixed release clamp onto the back rail so

thatthefixedportionisflushagainstandrestsontopof

themountinghookandislocatedbetweentheseatrail

andthebottomofthemountinghook.

5. Reinstallthesleeve,lockwasher,andinternalmount-

ing screw into the fixed release clamp and torque to

75-inchpounds.

6. Repeat STEPS 1-5 for other side.

7. Once fixed release mounting clamps are secured, do

one(1)offollowing:

A. RefertoQUICKRELEASECLAMPSFORSEAT

in PROCEDURE 2 of this instruction sheet.

B. RefertoUSINGCLAMPSinthisinstructionsheet.

5. Reinstallthemountingscrew,lockwasher,andinter-

nal mounting screw into the fixed release rail/cane

clamp and torque to 75 - inch pounds.

6. Repeat STEPS 1 - 5 for other side.

7. Once fixed release mounting clamps are secured,

doone(1)offollowing:

A. Refer to QUICK RELEASE CLAMPS FOR

SEATinPROCEDURE2ofthisinstructionsheet.

B. Refer to USING CLAMPS in this instruction

sheet.

Quick Release Clamps For Seat (FIGURE 4)

NOTE: Refer to INSTALLATION WARNING in the

SAFETY SUMMARY before proceeding.

NOTE: The quick release and fixed release clamps are

designed to fit either 1-inch rail tubing or, with insert pro-

vided,7/8-inchrailtubing.

1. Removethesleeve,lockwasher,andinternalthreaded

mounting screw from the quick release clamp (DE-

TAIL “C”).

2. Place the quick release clamp on the seat rail.

3. Ifquickreleaseclampisnottightlyfittedaroundseatrail

tubing,installinsertprovidedasshowninDETAIL“C”.

USING CLAMPS

Twist Release (FIGURE 5)

1. To unlock cane clamp, twist away from back cane.

2. To lock the cane clamp, twist in toward the back.

Twist Release

Cane Clamp

Back

Mounting

Hook

Unlock

Back Cane

TOP VIEW

FIGURE 5 - USING CLAMPS - TWIST RELEASE

FIGURE 6 - USING CLAMPS - QUICK RELEASE

Wheelchair

Frame Mounting

Hook

TO UNLOCK APPLY

PRESSURE HERE

Quick Release

Rail Clamp

Fixed Release

Clamp

Back Cane

Fixed

Portion

Quick Release

Clamp

Fixed

Portion Release

Portion

Mounting

Hooks

FIGURE 4 - QUICK RELEASE AND FIXED

RELEASE CLAMPS FOR SEAT

DETDET

DETAILAIL

AILAIL

AIL “C”“C”

“C”“C”

“C”

Lock Washer

Sleeve

Internal

Mounting

Screw

Insert

TO LOCK APPLY

PRESSURE HERE

Quick Release (FIGURE 6)

1. To unlock, pushdownonthe release tabofthequick

release rail clamps.

2. To lock, push down on the thumb-like feature of the

quick release rail clamps.

Invacare Corporation www.invacare.com

USA Canada

One Invacare Way 5970 Chedworth Way Invacare is a registered trademark of Invacare Corporation.

Elyria, Ohio USA Mississauga, Ontario Yes, you can is a trademark of Invacare Corporation.

800-333-6900 905-890-8838 Form No. 97-186 Part No. 1074563 Rev C (1) 03/01

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Invacare Aide à la mobilité

Invacare

Invacare Non-Removable Device 1820 Manuel utilisateur

Invacare

Invacare 2218 Instructions de montage

Invacare

Invacare Quick Release Caster Manuel utilisateur

Invacare

Invacare Robin Manuel utilisateur

Invacare

Invacare 65550 Instructions de montage

Invacare

Invacare 1335 Manuel utilisateur

Invacare

Invacare Ulti-Mate Air Back Manuel utilisateur

Invacare

Invacare 65109 Instructions de montage

Invacare

Invacare Elf 127em Manuel utilisateur

Invacare

Invacare 8153-J Manuel utilisateur

Invacare

Invacare User guide Manuel utilisateur

Invacare

Invacare 3G Storm Series Mode d’emploi

Invacare

Invacare DOLOMITE Melody Manuel utilisateur

Invacare

Invacare Excel Mode d’emploi

Invacare

Invacare Aquatec Marine Manuel utilisateur

Invacare

Invacare Front Anti Tippers 1326 Manuel utilisateur

Invacare

Invacare Dolomite Gloss Manuel utilisateur

Invacare

Invacare Birdie Manuel utilisateur

Invacare

Invacare Kirilos Manuel utilisateur

Invacare

Invacare 1141466 Instructions de montage

Invacare

Invacare Powered Seating Manuel utilisateur

Invacare

Invacare CMEX Manuel utilisateur

Invacare

Invacare 1130213 Manuel utilisateur

Invacare

Invacare 6098 Manuel utilisateur

Manuels Aide à la mobilité populaires d'autres marques

Alber

Alber Scalamobil iQ Manuel utilisateur

Ferno

Ferno CCT-PX Manuel utilisateur

HEPRO

HEPRO Gripo Manuel utilisateur

Otto Bock

Otto Bock Pheon 3R62 Manuel utilisateur

NRS Healthcare

NRS Healthcare M11090 Manuel utilisateur

Medline

Medline MDS86835DSHEC Guide d'installation

Guldmann

Guldmann Twin Turner II Manuel utilisateur

Drive

Drive ROOMBA Manuel utilisateur

Gate

Gate Balder Manuel utilisateur

Decon wheel

Decon wheel TNS Notos Manuel utilisateur

ExoAtlet

ExoAtlet ExoAtlet-II Manuel utilisateur

Rhythm Healthcare

Rhythm Healthcare B3800F Manuel utilisateur

AMF-BRUNS

AMF-BRUNS PROTEKTOR Manuel utilisateur

Drive DeVilbiss Healthcare

Drive DeVilbiss Healthcare OTTER Manuel utilisateur

Rhythm Healthcare

Rhythm Healthcare C500U Manuel utilisateur

Lumex

Lumex RJ4200A Manuel utilisateur

Rebotec

Rebotec Jumbo Manuel utilisateur

Rehaforum MEDICAL

Rehaforum MEDICAL PR50548 Manuel utilisateur