Intermec PM4I Manuel utilisateur

Use these installation instructions to replace the power supply unit (PSU) on

the PM4i printer. The PSU kit ships with these items:

•Power supply unit (P/N 1-971131-003)

•This installation instruction sheet

To install the power supply unit, you need:

•T20 Torx screwdriver

To install the power supply unit

1Turn off the printer power and remove the power cord.

2Lay the printer on its left cover (the electronics and front cover).

PM4i

This installation procedure must only be performed by an

authorized Intermec service technician. Intermec assumes no

responsibility for personal injury or damage to the

equipment if the installation is performed by an

unauthorized person.

The electrical components in the printer are susceptible to

damage from electrostatic discharge (ESD). You must

follow standard ESD guidelines to avoid damaging the

equipment you are servicing.

Power Supply Unit Installation Instructions

3Remove the four T20 Torx screws from the bottom of the printer and then set

the printer back upright.

4Open the media cover and remove the four T20 Torx screws that attach the

electronics and front cover to the printer.

Screw

(4 places)

Screw

(4 places)

5Lift the electronics and front cover door away from the printer and carefully

disconnect the console cable from the CPU board.

6Disconnect all of the cables from the CPU board.

7Remove the four T20 Torx screws and the standoff that attach the CPU board to

the power supply unit and lift it away from the printer.

Screw

(4 places)

Worldwide Headquarters

6001 36th Avenue West

Everett, Washington 98203

U.S.A.

tel 425.348.2600

fax 425.355.9551

www.intermec.com

© 2009 Intermec Technologies

Corporation. All rights reserved.

PM4i Power Supply Unit Installation Instructions

*931-067-001*

P/N 931-067-001

8Remove the six T20 Torx screws that attach the power supply unit to the printer,

disconnect the cables from it, and lift it away from the printer.

9To replace the power supply unit, reverse Steps 1 through 8. You need to reuse

the ground (GND) cable (P/N 236-068-003) and the cooling plate

(P/N 1-206170-00).

Note: When you remove the screws that attach the power supply unit to

the printer, the rear panel of the printer will detach.

Note: Make sure that you attach the GND cable through the lower left

screw when you replace the power supply unit.

Screw

(6 places)

Ground

cable

Autres manuels pour PM4I

18

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels Intermec Accessoires pour imprimantes

Intermec

Intermec PW50 Manuel utilisateur

Intermec

Intermec EasyCoder PF2i Manuel utilisateur

Intermec

Intermec EasyCoder PF2i Manuel utilisateur

Intermec

Intermec PB50 Manuel utilisateur

Intermec

Intermec PW50 Manuel utilisateur

Intermec

Intermec EasyCoder F4 Manuel utilisateur

Intermec

Intermec EasyCoder PD41 Manuel utilisateur

Intermec

Intermec 825-192-001 Manuel utilisateur

Intermec

Intermec EasyCoder 3400e Manuel utilisateur

Intermec

Intermec EasyCoder 601XP Manuel utilisateur

Intermec

Intermec PM4I Manuel utilisateur

Intermec

Intermec PM4I Manuel utilisateur

Intermec

Intermec PB50 Manuel utilisateur

Intermec

Intermec PM4I Manuel utilisateur

Intermec

Intermec PB41 Manuel utilisateur

Intermec

Intermec UBI EasyCoder 601 E Mode d’emploi

Intermec

Intermec PB42 Manuel

Intermec

Intermec PB42 Manuel utilisateur

Intermec

Intermec EasyCoder PF2i Manuel utilisateur

Intermec

Intermec PB42 Manuel

Intermec

Intermec PA30 Manuel utilisateur

Intermec

Intermec EasyCoder F4 Manuel utilisateur

Intermec

Intermec 3600 Manuel utilisateur

Intermec

Intermec EasyCoder 3400e Manuel utilisateur

Manuels Accessoires pour imprimantes populaires d'autres marques

Star Micronics

Star Micronics TSP800 Series Manuel utilisateur

REA

REA JET HR pro 2K Manuel utilisateur

HP

HP Laserjet,Color Laserjet 4si Manuel utilisateur

oliser

oliser MS 45 Manuel utilisateur

Roland

Roland DU2-64 Instructions et recettes

Xerox

Xerox EFI EXP6000 Manuel utilisateur

Canon

Canon Finisher-T1 Manuel utilisateur

Sharp

Sharp FO-1MK Manuel utilisateur

Labelmate

Labelmate PM-300 Manuel utilisateur

Epson

Epson T6248 Manuel d'utilisation

Epson

Epson OT-BZ20 Manuel utilisateur

Canon

Canon TonerRobot EP-27 Manuel utilisateur

Ricoh

Ricoh LCIT RT5100 Guide de démarrage rapide

GBC

GBC 16 Series Manuel utilisateur

Canon

Canon INNER 2-WAY TRAY-E1 Manuel d'utilisation et d'entretien

Develop

Develop SD-509 Manuel utilisateur

Kyocera

Kyocera KM-6230 Manuel

Triumph Adler

Triumph Adler DF-710 Manuel