Interlogix TVC-5120-1 Manuel utilisateur
P/N 1072501A • ISS 20SEP12
TVC-5120-1 Box Camera
Pocket Guide
Overview
This is the pocket guide for TVC-5120-1-P / TVC-
5120-1-N Box Camera. It is used indoors. However, if
installed in a housing, it can be used outdoors. The
guide describes a standard installation.
The camera consists of the following:
Camera body
CCD protection cap
Spare lens connector (male)
Refer to the figures in the front of the guide when
performing the camera setup procedures.
Note: Check the package and contents for visible
damage. If any components are damaged or missing,
do not attempt to use the unit, contact the supplier
immediately. If the unit must be returned, it must be
shipped back in its original packaging.
2
1: Setting the lens mode
1. Camera
2. Autoiris lens connector
3. Autoiris lens plug
4. Lens (Autoris lens shown. Manual lens has no
cable)
5. C-mount adaptor
6. DC-type autoiris lens leads: Damping coil
positive (A) and negative (B), Driving coil
positive (C) and negative (D)
3
2: Connecting power
3: Recommend DIP switch settings
Fixed lens: DC iris lens:
4
Installation
To install the camera:
1. Connect a coaxial cable terminated with BNC
connectors between the VIDEO OUT connector
of the camera and the video in connector on a
monitor, multiplexer, switcher, or other standard
video device.
2. To attach the lens, please refer to the
instructions that came with the lens. See Figure 1
on page 1 for guidance.
Note: If you are using a C-mount lens, screw on
the provided C-mount adapter. For optimal
performance, use an auto iris lens.
3. To connect power, loosen the DC12V and GND
terminal screws on the terminal block using a
screwdriver. Connect a universal 12 VDC power
supply to the terminal block. Retighten the
terminal screws until snug, ensuring that the
power leads are secure. Supply power to the unit
by plugging the power supply into a proper
source.
The power LED illuminates to show that the
camera is receiving power. If it does not
illuminate, check the terminal block connections
and the power source
5
4. Set the DIP switches. See the table below and
Figure 3 on page 3 for the recommended
settings.
Item Description Remark
AI Auto Iris For autoiris lens only, the
shutter is fixed 1/50 (PAL)
AE Auto
Electronic
shutter
For fixed lens. As the iris
is fixed, the camera
automatically sets the
optimum shutter speed.
FLK Flickerless Flickerless mode avoids
interference from light
sources (recommended
for DC-iris lenses only ).
BLC Back Light
Compensation
Selectively amplifies parts
of the image to
compensate for large
contrast differences when
only a portion of the
image is brightly lit.
6
Specifications
Power supply 12 VDC
Current 85 mA
Power consumption 1 W max.
Operating temperature -10to +50 °C
(14 to 122°F)
Storage temperature -20to70 °C
(-4 to +158°F)
Weight 305 g (0.67 lb.)
Dimensions (H × W × L) 56 x 50 x 125 mm
(2.2 x 4.9 x 4.95 in.)
Contact information
For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu.
Regulatory information
© 2012 UTC Fire & Security. All rights reserved.
Manufacturer
UTC Fire & Security Americas Corporation, Inc.
2955 Red Hill Avenue, Costa Mesa, CA 92626 5923, USA
Authorized EU manufacturing representative:
7
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
FCC compliance
Class B: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications.
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
ACMA compliance
Notice! This is a Class A product. In a domestic environment
this product may cause radio interference in which case the
user may be required to take adequate measures.
Canada
This Class A digital apparatus complies with Canadian ICES-
003.
Cet appareil numérique de la classe A est conforme à la
norme NMB-0330 du Canada.
Certification
N4131
European Union directives
12004/108/EC (EMC directive): Hereby, UTC Fire & Security
declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive
8
2004/108/EC.
2002/96/EC (WEEE directive): Products
marked with this symbol cannot be
disposed of as unsorted municipal waste in
the European Union. For proper recycling,
return this product to your local supplier
upon the purchase of equivalent new
equipment, or dispose of it at designated
collection points. For more information see:
www.recyclethis.info.
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Interlogix Caméra de sécurité
Interlogix
Interlogix TruVision TVD-2402 Manuel utilisateur
Interlogix
Interlogix PIR Manuel utilisateur
Interlogix
Interlogix TruVision TVA-1101 Manuel utilisateur
Interlogix
Interlogix UVC-XP4DN-HR Manuel utilisateur
Interlogix
Interlogix TruVision Series Manuel utilisateur
Interlogix
Interlogix UltraView Manuel utilisateur
Interlogix
Interlogix TruVision TVB-4402 Manuel utilisateur
Interlogix
Interlogix TruVision TVW-2401 Feuille d'instructions
Interlogix
Interlogix TVF-1101 Manuel utilisateur
Interlogix
Interlogix TVB-2201 Manuel utilisateur
Interlogix
Interlogix TruVision HD-TVI 3MPX Feuille d'instructions
Interlogix
Interlogix 36X Manuel utilisateur
Interlogix
Interlogix TruVision Line Manuel
Interlogix
Interlogix TruVision TVB-4410 Manuel
Interlogix
Interlogix TruVision TVB-2402 Manuel utilisateur
Interlogix
Interlogix TruVision Line Feuille d'instructions
Interlogix
Interlogix UVC-XP4DN-HR Manuel utilisateur
Interlogix
Interlogix True Vision TVP-5104 Manuel utilisateur
Interlogix
Interlogix TruVision TVB-2402 Feuille d'instructions
Interlogix
Interlogix TruVision Series Manuel utilisateur
