Intel NUC7i5BNH Manuel utilisateur

Intel NUC Kit NUC7i7BNH, NUC7i5BNH & NUC7i3BNH User Guide

Intel® NUC Kit NUC7i7BNH

Intel® NUC Kit NUC7i5BNH

Intel® NUC Kit NUC7i3BNH

User Guide

Intel NUC Kit NUC7i7BNH, NUC7i5BNH & NUC7i3BNH User Guide

Before You Begin

CAUTIONS

The procedures in this user guide assume familiarity with the general terminology associated with

personal computers and with the safety practices and regulatory compliance required for using

and modifying electronic equipment.

Disconnect the computer from its power source and from any telecommunications link or network before

performing any of the procedures described in this guide. Failure to disconnect power,

telecommunications links, or networks before you open the computer or perform any procedures can

result in personal injury or equipment damage. Some circuitry on the board can continue to operate even

though the front panel power button is off.

Follow these guidelines before you begin:

•Always follow the steps in each procedure in the correct order.

•Set up a log to record information about your computer, such as model, serial numbers, installed

options, and configuration information.

•Electrostatic discharge (ESD) can damage components. Perform the procedures described in this

chapter only at an ESD workstation using an antistatic wrist strap and a conductive foam pad. If

such a station is not available, you can provide some ESD protection by wearing an antistatic wrist

strap and attaching it to a metal part of the computer chassis.

Installation Precautions

When you install and test the Intel NUC, observe all warnings and cautions in the installation

instructions.

To avoid injury, be careful of:

•Sharp pins on connectors

•Sharp pins on circuit boards

•Rough edges and sharp corners on the chassis

•Hot components (such as SSDs, processors, voltage regulators, and heat sinks)

•Damage to wires that could cause a short circuit

Observe all warnings and cautions that instruct you to refer computer servicing to qualified

technical personnel.

Observe Safety and Regulatory Requirements

If you do not follow these instructions, you increase your safety risk and the possibility of

noncompliance with regional laws and regulations.

Intel NUC Kit NUC7i7BNH, NUC7i5BNH & NUC7i3BNH User Guide

This guide tells you how to:

•Install an M.2 SSD

•Install and remove memory

•Install a 2.5” drive

•Install a VESA mount bracket

•Connect power

•Install an operating system

•Install the latest device drivers and software

Open the Intel NUC Chassis

To open the Intel NUC chassis, follow these steps:

1. Unscrew the four corner screws on the bottom cover of the chassis and lift the cover.

Install an M.2 SSD

Intel NUC Kits NUC7i7BNH, NUC7i5BNH, and NUC7i3BNH support 80mm and 42mm M.2 SSDs. For a list

of tested M.2 SSDs, go to the Intel® Product Compatibility Tool:

•NUC7i7BNH

•NUC7i5BNH

•NUC7i3BNH

Intel NUC Kit NUC7i7BNH, NUC7i5BNH & NUC7i3BNH User Guide

Observe the precautions in "Before You Begin" on page 2.

If you are installing an 80mm M.2 SSD:

1. Remove the small silver screw from the 80mm metal standoff on the motherboard (A).

2. Remove the standoff from the 42mm position (B).

3. Align the small notch at the bottom edge of the M.2 card with the key in the connector.

4. Insert the bottom edge of the M.2 card into the connector (C).

5. Secure the card to the standoff with the small silver screw (D).

If you are installing a 42mm M.2 SSD:

1. Remove the small silver screw from the metal standoff on the motherboard (A).

2. Align the small notch at the bottom edge of the M.2 card with the key in the connector.

3. Insert the bottom edge of the M.2 card into the connector (B).

4. Secure the card to the standoff with the small silver screw (C).

Intel NUC Kit NUC7i7BNH, NUC7i5BNH & NUC7i3BNH User Guide

Installing and Removing Memory

Intel NUC Kits NUC7i3BNH and NUC7i5BNH have two DDR4 SO-DIMM sockets. Memory requirements:

•1.2V memory

•1866 MHz or 2133 MHz SO-DIMMs

•Non-ECC

For a list of tested memory, go to the Intel® Product Compatibility Tool:

•NUC7i7BNH

•NUC7i5BNH

•NUC7i3BNH

Install SO-DIMMs

If you plan to install just one SO-DIMM, install it in the lower memory socket.

To install the SO-DIMMs, follow these steps:

1. Observe the precautions in "Before You Begin" on page 2.

2. Turn off all peripheral devices connected to the computer. Turn off the computer and

disconnect the AC power cord.

3. Align the small notch at the bottom edge of the SO-DIMM with the key in the socket.

4. Insert the bottom edge of the SO-DIMM into the socket.

5. When the SO-DIMM is inserted, push down on the outer edge of the SO-DIMM until the

retaining clips snap into place. Make sure the clips are firmly in place.

Removing SO-DIMMs

To remove a SO-DIMM, follow these steps:

1. Observe the precautions in "Before You Begin" on page 2.

2. Turn off all peripheral devices connected to the computer. Turn off the computer.

3. Remove the AC power cord from the computer.

4. Remove the computer’s cover.

Intel NUC Kit NUC7i7BNH, NUC7i5BNH & NUC7i3BNH User Guide

5. Gently spread the retaining clips at each end of the SO-DIMM socket. The SO-DIMM pops out of

the socket.

6. Hold the SO-DIMM by the edges, lift it away from the socket, and store it in an anti-static package.

7. Reinstall and reconnect any parts you removed or disconnected to reach the SO-DIMM sockets.

8. Replace the computer’s cover and reconnect the AC power cord.

Install a 2.5” SSD or Hard Drive

For a list of tested 2.5” hard drives, go to the Intel® Product Compatibility Tool:

•NUC7i7BNH

•NUC7i5BNH

•NUC7i3BNH

Follow these instructions to install a 2.5” Solid State Drive (SSD) or Hard Disk Drive (HDD):

1. Observe the precautions in "Before You Begin" on page 2.

2. Slide the 2.5” drive into the drive bay, ensuring the SATA connectors are fully seated into the

connectors of the SATA daughter card (A).

3. Secure the drive into the drive bay with the two small silver screws that were included in the box.

4. Set the drive bay bracket down inside the chassis (B).

Intel NUC Kit NUC7i7BNH, NUC7i5BNH & NUC7i3BNH User Guide

Close the Chassis

After all components have been installed, close the Intel NUC chassis. Intel recommends this be done by

hand with a screwdriver to avoid over-tightening and possibly damaging the screws.

Attach and Use the VESA Bracket (Optional)

Follow these instructions to attach and use the VESA mount bracket:

1. Attach the VESA bracket to the back of the monitor or TV, using the four small black screws that

were included in the box.

Intel NUC Kit NUC7i7BNH, NUC7i5BNH & NUC7i3BNH User Guide

2. Attach the two slightly larger black screws to the bottom chassis cover of the Intel NUC.

3. Slide the Intel NUC onto the VESA mount bracket.

Connect Power

Country-specific power plug attachments are included in the Intel NUC Kit box.

1. Choose the attachment for your region.

SKU

(Product

codes)

Attachments in the box

NUC7i7BNH

NUC7i7BNHR

NUC7i5BNH

NUC7i5BNHR

NUC7i3BNH

NUC7i3BNHR

Intel NUC Kit NUC7i7BNH, NUC7i5BNH & NUC7i3BNH User Guide

US –United States

UK –United

Kingdom

EU –European

Union

AUS - Australia

NUC7i7BNHL

NUC7i5BNHL

NUC7i3BNHL

ARG - Argentina

CHN - China

BRA - Brazil

IND - India

KOR –South Korea

2. Slide the attachment (B) onto the power plug, locking it into place (A).

Intel NUC Kit NUC7i7BNH, NUC7i5BNH & NUC7i3BNH User Guide 
10 
 
3. Connect AC power. 
 
 
Install an Operating System 
 Refer to Supported Operating Systems for a list of Intel-validated Windows* operating systems, as well as 
versions of Linux that have been reported as compatible by Intel NUC owners. 
 Refer to Operating System Installation for system requirements and installation steps. 
 
Install the Latest Device Drivers and Software 
 
Here are the options for keeping device drivers current: 
•Allow the Intel® Driver & Support Assistant (Intel® DSA) to detect out-of-date drivers 
•Manually download drivers, BIOS, and software from Download Center: 
oNUC7i3BNH 
oNUC7i5BNH 
oNUC7i7BNH 
 
The following device drivers and software are available. 
•Intel® Chipset Device Software 
•Intel® HD Graphics 
•Intel® Management Engine 
•Intel® Wireless 
•Intel® Bluetooth 
•Intel® Gigabit Ethernet 
•Thunderbolt™ Bus (NUC7i5BNH and NUC7i7BNH only) 
•Realtek* High Definition Audio 
•Realtek* Card Reader 
•ITE Tech* Consumer Infrared 
•Intel® Rapid Storage Technology 
•Intel® Software Guard Extensions 
•Thunderbolt™ 3 Controller Firmware 
•HDMI Firmware 

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Intel Matériel informatique

Intel

Intel Braswell Series Manuel utilisateur

Intel

Intel D875PBZ - Desktop Board Motherboard Manuel utilisateur

Intel

Intel Core 2 Duo Processor Manuel utilisateur

Intel

Intel Enpirion EM2COMIF Manuel utilisateur

Intel

Intel Core i7-2600 Gain Instructions d'utilisation et de sécurité

Intel

Intel 80286 Manuel utilisateur

Intel

Intel E7500 Mode d’emploi

Intel

Intel 87C196CA Manuel utilisateur

Intel

Intel SBC 711 Guide rapide de l'utilisateur

Intel

Intel 5400 Series Mode d’emploi

Intel

Intel 80C186EA Manuel du propriétaire

Intel

Intel BX80605X3440 - Quad Core Xeon X3440 Manuel de service

Intel

Intel Xeon X5570 Manuel utilisateur

Intel

Intel SL7PG - Xeon 3.4 GHz/800MHz/1MB Cache CPU... Manuel utilisateur

Intel

Intel RS2BL040 - Raid Controller Manuel d'installation

Intel

Intel 945G - Bulk Single Unit Atx Exp Manuel utilisateur

Intel

Intel i7-3770 Instructions d'utilisation et de sécurité

Intel

Intel CD1M3128MK Guide de configuration

Intel

Intel PXA27 Series Mode d’emploi

Intel

Intel SASMF8I - RAID Controller Manuel d'installation

Intel

Intel 520J - Pentium 4 2.80GHz 800MHz 1MB Socket 775... Manuel utilisateur

Intel

Intel X3350 - Xeon 2.66 Ghz 12M L2 Cache 1333MHz FSB LGA775 Quad-Core... Mode d’emploi

Intel

Intel 80C186XL Manuel utilisateur

Intel

Intel SRCSASLS4I - RAID Controller Manuel d'installation

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur

Advantech

Advantech ASMB-935 Series Manuel utilisateur

Jupiter

Jupiter RAM PACK Manuel utilisateur