Intel 486MIS Manuel utilisateur

PREFACE

Thank you for purchasing the 486MIS system board. This document

gives an aid to the configuration and installation of this system board.

The information in this document is subject to change ithout notice.

This document contains information protected by copyright. All rights are

reserved. No part of this document may be used or reproduced in any

forms or by any means, or stored in a database or retrieval system,

ithout prior ritten permission.

TRADEMARKS

Intel is a registered trademark of Intel Corporation.

IBM is a registered trademark of International Business Machines

Corporation.

Microsoft is a registered trademark of Microsoft Corporation.

VESA is a registered trademark of Video Electronics Standard

Association.

All other trademarks used in this manual are the property of their

respective o ners.

486MIS System Board User's Manual Page 1

TABLE OF CONTENTS

CHAPTER 1: INTRODUCTION 4

CHAPTER 2: JUMPERS & CONNECTORS 6

SYSTEM BOARD JUMPERS 6

CPU External Cl ck Jumpers 8

CPU Type Jumpers 8

Cache Size Jumpers 9

VESA L cal Bus Jumper 9

Clear Passw rd Jumper 10

Display Type Jumper 10

FLASH BIOS Jumper 11

SCSI P rt Jumper Bl ck W1 11

IDE P rt Jumpers 12

Parallel P rt Jumper 12

SYSTEM BOARD CONNECTORS 13

P wer Supply C nnect rs 13

Keyb ard C nnect r 14

P wer LED and Keyb ard L ck C nnect r 14

Speaker C nnect r 15

Reset C nnect r 15

Turb Switch C nnect r 16

Turb LED C nnect r 16

Parallel P rt C nnect r 17

Serial P rt 1 & 2 C nnect rs 17

Fl ppy Interface C nnect r 18

IDE Interface C nnect r 19

Harddisk Activity LED C nnect r 19

SCSI Interface C nnect r 20

CHAPTER 3: HARDWARE INSTALLATION 21

THE DRAM SIMMs 21

Installing DRAM SIMMs 22

INSTALLING A VL-BUS CARD 23

EQUIPMENT REQUIRED 24

SCSI / IDE SETUP 25

SCSI ID Setup 25

SCSI Device Terminati n 25

SCSI Default Setting 25

SCSI/IDE Dual Operati n 25

CHAPTER 4: BIOS SETUP 27

ENTERING SETUP 27

STANDARD CMOS SETUP 29

ADVANCED CMOS SETUP 30

AUTO CONFIGURATION - BIOS DEFAULTS 33

AUTO CONFIGURATION - POWER-ON DEFAULTS 33

CHANGE PASSWORD 34

Page 2 486MIS System Board User's Manual

AUTO DETECT HARD DISK 35

HARD DISK UTILITY 35

WRITE TO CMOS AND EXIT 35

DO NOT WRITE TO CMOS AND EXIT 35

CHAPTER 5: DOS/WINDOWS DRIVERS 36

DOS/WINDOWS DRIVERS QUICK INSTALLATION 36

ASPI2DOS ASPI MANAGER 37

aspi2d s C mmand Line Opti ns 37

DOS/WINDOWS DRIVERS FORMATTING UTILITIES 41

L w-Level F rmatting with scsifmt 41

Partiti ning & High-Level F rmatting with afdisk 42

Viewing Device Inf rmati n with sh wscsi 44

Playing Audi CDs with cdplayer 46

CHAPTER 6: OS/2 v2.1 DRIVERS 49

INSTALLATION 49

COMMAND LINE USAGE 50

CHAPTER 7: NOVELL NETWARE 3.1X, 4.0X 51

INSTALLATION 51

APPENDIX A: KEYBOARD SPEED SWITCH 54

APPENDIX B: AMI BIOS HARD DISK TYPE 55

APPENDIX C: MEMORY MAPPING 56

APPENDIX D: AT I/O ADDRESS MAP 57

APPENDIX E: INTERRUPT ASSIGNMENTS 59

APPENDIX F: SPECIFICATION 60

486MIS System Board User's Manual Page 3

CHAPTER 1: INTRODUCTION

The 486MIS system board adds to our 486 product line high integration

and cost effective solution ithout compromising performance and

quality. With top speed at 50MHz and integrated 64K/128K/256K Write-

Back cache, the 486MIS dramatically boosts system throughput for even

the most demanding applications. The 486MIS offers features and

functionality exceeding any other system board in its class, including:

CPU:

·Intel i486DX, i486DX2, i486SX, i487SX, P24T, and Overdrives.

Cache Memory:

·Supports 64K/128K/256K/512K cache memory.

Main Memory:

·Supports 512Kx36, 1Mx36, 2Mx36, 4Mx36, and 8Mx36 72-pin SIMM

modules.

·Up to 64 MBytes on-board memory.

S ots:

·T o 32-bit VESA Local Bus (VL-Bus) slots.

·Six 16-bit ISA bus slots.

On-Board Battery:

·Use Dallas compatible DS1287 Real-Time-Clock and Battery ith

over 10 years of operation in the absence of po er.

SCSI Port:

·32-bit VL-Bus interface ith 128-byte data buffer to increase

performance.

·Compatible ith Adaptec 1510/1520/1522 SCSI-2 adapters.

Page 4 486MIS System Board User's Manual

·Supports Processor Programmed I/O.

·Multitasking ASPI manager for DOS.

·On-board BIOS supports boot capability, and up to t o hard disk

drives under DOS ithout a soft are driver.

·Supports ide range of both synchronous and asynchronous

devices: disk, Tape, CD-ROM, WORM, DAT, and other SCSI

peripherals.

IDE Port:

·Turbo/Normal selections for fast or slo IDE hard drives.

·Plug and play, replaces any non-intelligent IDE controller ithout

reformatting the disk drives.

·Soft are drivers are not required for all operating systems.

F oppy Disk Contro er:

·Fully IBM register set compatible.

·Supports up to t o 3.5-inch or 5.25-inch floppy disk drives.

·Supports 360KB / 720KB / 1.2MB / 1.44MB densities.

·Floppy Disk Controller can be disabled.

Periphera s:

·Supports t o Serial ports and one Parallel port.

486MIS System Board User's Manual Page 5

CHAPTER 2: JUMPERS & CONNECTORS

When working with the 486MIS,

it is extreme y important that

you avoid static e ectricity.

A ways ground yourse f by

wearing a wrist or ank e strap.

Figures 1 on the next page sho s the component layout of the 486MIS

system board ith locations of the system board jumpers and

connectors. Note that most jumpers and connectors on the system board

are labeled ith proper names ith pin 1 marked as '1'. To avoid

damaging the board and to have proper operation caution should be

taken hen connecting these components.

SYSTEM BOARD JUMPERS

Jumpers are used to select bet een various operating modes. A jumper

s itch consists of t o, three, or four gold pins projecting from the system

board. Placing the plastic jumper cap over t o pins connects those pins

and makes a particular selection. Using the cap to cover t o pins in this

ay is referred to as shorting those pins. If the cap is not placed on any

pins at all, this is referred to as leaving the pins open.

Note: When you open a jumper, leave the plastic jumper cap attached

to one of the pins so you don't lose it.

Page 6 486MIS System Board User's Manual

FIGURE

486MIS System Board User's Manual Page 7

CPU Externa C ock Jumpers

If you are installing an i486DX, or i486SX the internal CPU clock speed is

the same as the external CPU clock speed. This is different for i486DX2

CPU here the external speed is one-half of the internal speed. For

example, a 486DX2-66 has an external clock speed of 33MHz.

CPU Externa

C ock Speed

JP3 JP4 JP5 ID3

20MHz OPEN SHORT SHORT 1-2

25MHz SHORT OPEN SHORT 1-2

33MHz SHORT SHORT OPEN 1-2

40MHz OPEN OPEN SHORT 2-3

50MHz OPEN SHORT OPEN 2-3

CPU Type Jumpers

CPU Type JP1 JP2 JP18

486DX, 486DX2 1-2 1-2, 3-4 1-2

487SX, ODP486SX 2-3 1-2, 3-4 1-2

486SX OPEN 2-3 1-2

Cyrix 486DLC OPEN 2-3 2-3

Care should be taken hen installing the CPU into the Pin Grid Array

(PGA) socket on the system board. Make certain that pin 1 of the CPU

chip is correctly aligned ith pin 1 of CPU socket. The location of pin 1

on the CPU is denoted by a small notch.

Page 8 486MIS System Board User's Manual

Cache Size Jumpers

The system board supports 64KB/ 128KB/ 256KB/ 512KB of cache

memory.

Cache Size Jumper Selecti n

Cache

Size

JP7 JP8 JP9 JP10 JP11 JP12 JP13 JP14 JP15

64KB 1-2 1-2 1-2 1-2 1-2 1-2 1-2 1-2 2-3

128KB 1-2 1-2 2-3 2-3 2-3 1-2 1-2 1-2 1-2

256KB 2-3 1-2 2-3 2-3 2-3 2-3 2-3 1-2 2-3

512KB 2-3 2-3 2-3 2-3 2-3 1-2 2-3 2-3 1-2

Cache Size and SRAM L cati ns

Cache

Size

Tag RAM

U15

Data Bank 0

U20,U21,

U22,U23

Data Bank 1

U24, U25,

U26, U27

64KB 8Kx8 8Kx8 8Kx8

128KB 32Kx8 32Kx8 None

256KB 32Kx8 32Kx8 32Kx8

512KB 32Kx8 128Kx8 None

VESA Loca Bus Jumper

Jumper ID2 allo s any VL-Bus adapter to identify the speed of the

system board.

High Speed Write ID2

System board runs zero ait state rite

transfer. Some VL-Bus adapters may not

be able to run this mode.

1-2

System board runs one ait state rite

transfer. All VL-Bus adapters can operate

in this mode.

2-3

(Default)

486MIS System Board User's Manual Page 9

C ear Password Jumper

Jumper JP32 is used to clear the system pass ord if user ere to forget

it.

Function JP32

Normal Pass ord Operation OPEN

(Default)

BIOS performs infinite loop test and clears

system pass ord

SHORT

Follo these steps to clear system pass ord:

1. Turn po er OFF.

2. Open the system cover and gain access to jumper JP32 and W1.

3. Short jumper JP32 and disable SCSI BIOS through jumper block W1

as sho n belo :

¢¢¢¢¢

I1 I2 B1 B2 E

4. Turn po er ON.

5. Wait for the system to finish one self-test loop, then turn po er OFF

again.

6. Open jumper JP32 and re-enable SCSI BIOS through W1.

7. Replace and secure the system cover.

8. Turn po er ON, pass ord data should be cleared.

Disp ay Type Jumper

Disp ay Type JP16

Video display is VGA, EGA, or

Monochrome.

OPEN

(Default)

Video display is CGA. SHORT

FLASH BIOS Jumper

Page 10 486MIS System Board User's Manual

Table des matières

Autres manuels Intel Matériel informatique

Intel

Intel SRCSATAWB - RAID Controller Manuel d'installation

Intel

Intel U3-1L Manuel utilisateur

Intel

Intel BX80562Q6600 - Core 2 Quad 2.4 GHz Processor Manuel utilisateur

Intel

Intel i7-800 Manuel utilisateur

Intel

Intel P4000 - 11-2010 Manuel utilisateur

Intel

Intel Xeon Mode d’emploi

Intel

Intel RT3WB080 Manuel d'installation

Intel

Intel 852GME Mode d’emploi

Intel

Intel 386 Manuel utilisateur

Intel

Intel T8300 - Core 2 Duo 2.4GHz 800MHz 3MB Socket P Mobile... Manuel de l'opérateur

Intel

Intel SRCSASBB8I - RAID Controller Manuel d'installation

Intel

Intel Quad-Core Xeon Manuel utilisateur

Intel

Intel TS13X Manuel utilisateur

Intel

Intel E6700 - Core 2 Duo Dual-Core Processor Mode d’emploi

Intel

Intel SRCSASLS4I - RAID Controller Manuel d'installation

Intel

Intel Water 3.0 Performer C Manuel utilisateur

Intel

Intel NetStructure DM/V600-4E1-cPCI Instructions d'utilisation

Intel

Intel Intel CoreTM 2 Duo Processor Manuel utilisateur

Intel

Intel 6300ESB ICH Manuel utilisateur

Intel

Intel Xeon Processor E5-2600 Instructions de montage

Intel

Intel PXA27 Series Manuel utilisateur

Intel

Intel IB840 Manuel utilisateur

Intel

Intel SRCZCRX - RAID Controller Storage Manuel d'installation

Intel

Intel 845 DESIGN Mode d’emploi

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur

Advantech

Advantech ASMB-935 Series Manuel utilisateur

Jupiter

Jupiter RAM PACK Manuel utilisateur