IFM Electronic PN2 Series Manuel utilisateur

Operating instructions

Electronic pressure sensor

PN2 UKUK

80290848 / 00 08 / 2020

Contents

1 Preliminary note��3

1�1 Symbols used ��3

2 Safety instructions ��4

3 Functions and features ��4

3�1 Applications ��5

4 Function��5

4�1 Operating modes ��5

4�2 Communication, parameter setting, evaluation ��7

4�3 Switching function��7

4�4 Analogue function ��8

4�5 IO-Link ��9

4�5�1 General information ��9

4�5�2 Functions only available via IO-Link communication��10

5 Installation��10

6 Electrical connection�� 11

7 Operating and display elements ��12

8 Menu��13

8�1 Menu structure: main menu��13

8�2 Explanation of the menu��14

8�2�1 Explanation of menu level 1 ��14

8�2�2 Explanation of menu level 2 ��14

9 Parameter setting ��15

9�1 Parameter setting in general ��15

9�2 Define operating mode (optional) ��18

9�3 Configure display (optional)��18

9�4 Set output signals ��19

9�4�1 Set output functions��19

9�4�2 Define switching limits for the hysteresis function ��19

9�4�3 Define switching limits for the window function ��19

9�4�4 Scale analogue value ��20

9�5 User settings (optional)��20

9�5�1 Set delay time for the switching outputs ��20

9�5�2 Set output logic for the switching outputs ��21

9�5�3 Set damping for the switching signal ��21

9�5�4 Set damping for the analogue output ��21

9�5�5 Zero-point calibration��21

9�5�6 Reset all parameters to factory setting ��21

9�5�7 Set colour change of the display ��22

9�5�8 Graphical depiction of the colour change of the display ��23

9�6 Diagnostic functions ��25

9�6�1 Read min/max values for the system pressure ��25

9�6�2 Read overload processes��26

10 Operation��26

10�1 Read set parameters ��26

10�2 Self-diagnostics / fault indications ��26

11 Technical data ��28

11�1 Setting ranges��28

11�1�1 Setting ranges in operating mode 2��28

11�1�2 Setting ranges in operating mode 3��30

12 Factory setting ��34

1 Preliminary note

1.1 Symbols used

►Instruction

> Reaction, result

[…] Designation of keys, buttons or indications

→Cross-reference

Important note

Non-compliance may result in malfunction or interference

Information

Supplementary note

2 Safety instructions

• The device described is a subcomponent for integration into a system�

- The manufacturer is responsible for the safety of the system�

- The system manufacturer undertakes to perform a risk assessment and to

create a documentation in accordance with legal and normative requirements

to be provided to the operator and user of the system� This documentation

must contain all necessary information and safety instructions for the operator,

the user and, if applicable, for any service personnel authorised by the

manufacturer of the system�

• Read this document before setting up the product and keep it during the entire

service life�

• The product must be suitable for the corresponding applications and

environmental conditions without any restrictions�

• Only use the product for its intended purpose (→ Functions and features).

• Only use the product for permissible media (→ Technical data).

• If the operating instructions or the technical data are not adhered to, personal

injury and/or damage to property may occur�

• The manufacturer assumes no liability or warranty for any consequences

caused by tampering with the product or incorrect use by the operator�

• Installation, electrical connection, set-up, programming, configuration, operation

and maintenance of the product must be carried out by personnel qualified and

authorised for the respective activity�

• Protect units and cables against damage�

• If the devices are used in gas applications with pressures > 25 bar the notes in

chapter 3�1 for devices with the marking **)must be absolutely observed!

3 Functions and features

The device monitors the system pressure of machines and installations�

3.1 Applications

Type of pressure: relative pressure

Information on pressure rating and bursting pressure → data sheet.

Avoid static and dynamic overpressure exceeding the indicated pressure

rating by taking appropriate measures�

The indicated bursting pressure must not be exceeded�

Even if the bursting pressure is exceeded only for a short time, the unit

may be destroyed� ATTENTION: risk of injury!

The units are vacuum resistant�

Pressure Equipment Directive (PED):

The units comply with the Pressure Equipment Directive� They are

designed for group 2 fluids and are manufactured in accordance with

sound engineering practice� Use of media from group 1 fluids on request�

4 Function

• The unit displays the current system pressure�

• It generates output signals according to the operating mode and the parameter

setting�

• Moreover, it provides the process data via IO-Link�

• The unit is designed for fully bidirectional communication�

So the following options are possible:

- Remote display: reading and display of the current system pressure�

- Remote parameter setting: reading and changing the current parameter

setting�

- IO-Link parameter setting (→ 4.5)�

4.1 Operating modes

The following units are only supplied with operating mode [3]: PN2x12,

PN2x43, PN2x14, PN2x15� These units do not feature any other operating

mode and therefore menu item [CMPT] (→ 9.2) is not available�

Operating mode 2

Description Operating mode on delivery�

For exceptions, see note at the beginning of this chapter�

Application Standard applications�

IODD designation Example PN2094 Factory setting / (CMPT = 2):

At www�ifm�com in the download area of the corresponding article�

Operating mode 3

Description High IO-Link process value and parameter resolution

(device-specific: see IODD suitable for the operating mode)�

The menu items [ou1] and [ou2] are extended by the setting

option [OFF] (→ 9.4.1)�

IO-Link standard command "Flash" is available (→ 4.5.2)�

This operating mode is available as of device status BA�

For the device status see the labelling on the device�

BA xxxx

PNxxxx

Application Improved controllability via IO-Link�

Highly granular setting of set and reset points�

IODD designation Example PN2094 Status_B High Resolution / (CMPT = 3):

Example PN2012 Status_B

At www�ifm�com in the download area of the corresponding

article�

Manual selection of the operating mode see (→ 9.1),

selection of the operating mode via IO-Link interface see → Additional

document: Selection of the operating mode at www�ifm�com�

4.2 Communication, parameter setting, evaluation

OUT1 (pin 4) • Switching signal for system pressure limit

• Communication via IO-Link

OUT2 (pin 2) • Switching signal for system pressure limit

• Analogue signal 4��20 mA / 0��10 V

4.3 Switching function

OUTx changes its switching status if it is above or below the set switching limits

(SPx, rPx)� The following switching functions can be selected:

• Hysteresis function / normally open: [ou1/ou2] = [Hno] (→ Fig. 1).

• Hysteresis function / normally closed: [ou1/ou2] = [Hnc] (→ Fig. 1).

First the set point (SPx) is set, then the reset point (rPx)�

The hysteresis defined remains even if SPx is changed again�

• Window function / normally open: [ou1/ou2] = [Fno] (→ Fig. 2).

• Window function / normally closed: [ou1/ou2] = [Fnc] (→ Fig. 2).

The width of the window can be set by means of the difference between FHx

and FLx� FHx = upper value, FLx = lower value�























1 2

P = system pressure; HY = hysteresis; FE = window

When set to the window function the set and reset points have a fixed

hysteresis of 0�25 % of the measuring span�

4.4 Analogue function

OUT2 is an analogue output:

• [ou2] determines whether the set measuring range is provided as 4��20 mA

([ou2] = [I]) or as 0��10 V ([ou2] = [U])�

• Analogue start point [ASP2] determines at which measured value the output

signal is 4 mA or 0 V�

• Analogue end point [AEP2] determines at which measured value the output

signal is 20 mA or 10 V�

Minimum distance between [ASP2] and [AEP2] = 20 % of the measuring span�

Voltage output 0 ... 10 V:

Factory setting Measuring range scaled



























P =

MEW =

ASP =

AEP=

system pressure

final value of the measuring range

analogue start point [ASP2]

analogue end point [AEP2]

In the measuring range of the respective unit the output signal is between 0 and 10 V�

It is also indicated:

• System pressure above [AEP2]: 10��10�3 V

• Fault indication according to Namur: 11 V

Current output 4...20 mA

Factory setting Measuring range scaled

























 



P =

MEW =

ASP =

AEP=

system pressure

final value of the measuring range

analogue start point [ASP2]

analogue end point [AEP2]

In the measuring range of the corresponding unit the output signal is between 4 and

20 mA�

It is also indicated:

• System pressure above [AEP2]: 20��20�5 mA

• System pressure below [ASP2]: 4��3�8 mA

• Fault indication according to Namur: 21�5 mA

4.5 IO-Link

4.5.1 General information

The device has an IO-Link communication interface which requires an IO-Link-

capable module (IO-Link master) for operation�

The IO-Link interface enables direct access to the process and diagnostic data

and provides the possibility to set the parameters of the unit during operation�

In addition, communication is possible via a point-to-point connection with a USB

adapter cable�

The IODDs necessary for the configuration of the unit, detailed information about

process data structure, diagnostic information, parameter addresses and the

necessary information about the required IO-Link hardware and software can be

found at www�ifm�com�

4.5.2 Functions only available via IO-Link communication

• HIPC: number of overload processes (→ 9.6.2)�

• HIPS: threshold for the overload counter (→ 9.6.2)�

• Flash: via this standard command, the sensor can be localised in the plant�

When the command is used, the switching status LEDs flash and "IO-L" is

displayed� (Function only available in operating mode [3])�

• Application Specific Tag: freely definable text assigned to the unit�

• Function Tag: freely definable text describing the device function in the plant�

(Function only available in operating mode [3])�

• Location Tag: freely definable text describing the installation location in the

plant� (Function only available in operating mode [3])�

For more detailed information refer to the device-specific IO Device Description

PDF at www�ifm�com�

5 Installation

Before installing and removing the unit: Make sure that no pressure is

applied to the system�

►Insert the unit in a G¼ process connection�

►Tighten firmly� Recommended tightening torque:

Pressure range in bar Tightening torque in Nm

-1��400 25��35

600 30��50

Depends on lubrication, seal and pressure load!

The sensor housing can be rotated by 345° with regard to the process connection�

Do not rotate past the end stop!

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels IFM Electronic Accessoires

IFM Electronic

IFM Electronic O3M151 Manuel du propriétaire

IFM Electronic

IFM Electronic Efector 200 Manuel utilisateur

IFM Electronic

IFM Electronic PY995 Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 200 Manuel utilisateur

IFM Electronic

IFM Electronic Efector200 OG Manuel utilisateur

IFM Electronic

IFM Electronic efector100 GG507S Manuel utilisateur

IFM Electronic

IFM Electronic efector200 OGP3 Series Manuel utilisateur

IFM Electronic

IFM Electronic TS502A Manuel utilisateur

IFM Electronic

IFM Electronic efector160 LI214 Series Manuel utilisateur

IFM Electronic

IFM Electronic efector200 OC Manuel utilisateur

IFM Electronic

IFM Electronic VSA003 Manuel utilisateur

IFM Electronic

IFM Electronic efector 300 SI5004 Manuel utilisateur

IFM Electronic

IFM Electronic PA32xx Series Manuel utilisateur

IFM Electronic

IFM Electronic efector 300 SU9004 Manuel utilisateur

IFM Electronic

IFM Electronic Efector 500 PL2058 Manuel utilisateur

IFM Electronic

IFM Electronic EFECTOR200 OC Series Manuel utilisateur

IFM Electronic

IFM Electronic OGP Manuel utilisateur

IFM Electronic

IFM Electronic efector 160 LR8300 Manuel utilisateur

IFM Electronic

IFM Electronic Efector 200 Manuel utilisateur

IFM Electronic

IFM Electronic Efector 200 OI Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 200 OGT1 Series Manuel utilisateur

IFM Electronic

IFM Electronic LR2759 Manuel utilisateur

IFM Electronic

IFM Electronic O1D106 Manuel utilisateur

IFM Electronic

IFM Electronic efector200 OT Series Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Manuel utilisateur