ICP DAS USA ET-2260 Manuel utilisateur

English / Sep. 2015 / Version 1.0

T-

-2

The eSearch Utility can be obtained from either the companion CD-ROM or

from the ICPDAS website, as indicated below:

CD:\NAPDOS\software\eSearch\

http://ftp.icpdas.com/pub/cd/tinymodules/napdos/software/esearch/

Double-click the “eSearch_vxxx_setup.exe”file icon to execute the driver installation.

Click the “Next>”button to start the installation.

Select the destination location. The default path is C:\ICPDAS\eSearch. Verify that the destination

path is correct and click the “Next>”button.

Click the “Next>”button to continue.

Click the “Finish”button to complete the installation.

t’

’s

The package includes the following items:

ET-2260 Module Quick Start Guide (This Document) Companion CD

Pin Assignments:

Wire Connections:

(0xxxx) DO Address:

Starting

Address

Points

Description

Bits Per

Point

Range

Access

Type

0 (0x0)

1 ~ 6

Digital Output Channels

0: OFF, 1: ON

R/W

32 (0x20)

Clears the status of all high latched DI

channels

1: Clear

33 (0x21)

Clears the status of all low latched DI

channels

1: Clear

190 (0xBE)

1 ~ 6

Enables frequency measurement for all DI

Channels

0: Disable

1: Enable

(Default: 0)

R/W/F

235 (0xEB)

1 ~ 6

Sets the Power-on value for all DO Channels

0: OFF, 1: ON

(Default: 0)

R/W/F

267 (0x10B)

1 ~ 6

Sets the Safe value for all DO Channels

0: OFF, 1: ON

(Default: 0)

R/W/F

“R”: Read; “W”: Write; “F”:Settings are recorded in flash memory by default

(1xxxx) DI Address:

Starting

Address

Points

Description

Bits Per

Point

Range

Access

Type

0 (0x0)

1 ~ 6

Digital Input

0: OFF, 1: ON

32 (0x20)

1 ~ 6

Digital Latched Status (High)

0: NO

1: Latched

64 (0x40)

1 ~ 6

Digital Latched Status (Low)

0: NO

1: Latched

“R”: Read

For detailed information related to DI/DO Modbus Addresses, refer to Section 6.3 "Modbus

CD:\NAPDOS\ET2200\document\

http://ftp.icpdas.com/pub/cd/6000cd/napdos/et2200/document/

Ensure that the network settings on the Host PC have been correctly configured and are

functioning normally. Ensure that the Windows firewall or any Anti-Virus firewall is properly

configured to allow incoming connections, or temporarily disable these functions, otherwise the

“Search Servers” function in the eSearch Utility described in Section 7 may not perform as expected.

Contact the System Administrator for instructions of how to do this.

Connect both the ET-2260 module and the Host PC to the same sub network or the same Ethernet

Switch.

Apply power to the ET-2260 module. The valid power voltage range is from +10 to +30 VDC.

Verify that the “PWR”LED indicator on the ET-2260 module

is flashing.

-T

A tip for connecting the wire to the connector

A tip for removing the wire from the connector

Connect the NO0 pin (Pin01) to the GND pin (Pin02).

Connect the COM0 pin (Pin03) to the DI0pin (Pin04)

1. Use the blade of the

flat-head screwdriver to

push down the wire

clamp.

Insert the wire

Continue holding the

screwdriver in place

2. While holding the

screwdriver in place,

insert the wire into the

terminal block.

1. Use the blade of a

flat-head screwdriver to

push down the wire

clamp.

Remove the wire

Continue holding the

screwdriver in place

2. While holding the

screwdriver in place,

remove the wire from the

terminal block.

Execute the eSearch Utility and click the “Search Servers” button to search for the ET-2260

module.

Once the search process in complete, double-click the name of the ET-2260 module to open the

“Configure Server (UDP)” dialog box.

Enter the relevant values for the IP Address, Subnet Mask and Gateway, etc., and then click the

“OK” button. The new settings for the

ET-2260 module will take effect within 2

seconds. If the correct network

configuration information is unknown,

contact the Network Administrator to

obtain the relevant details.

Wait for 2 seconds and then click the “Search Servers” button again to ensure that the ET-2260

module is operating correctly using the new configuration.

Click the name of the ET-2260 module to select it.

Click the “Web”button to log in to the web configuration pages.

Factory Default Settings for

the ET-2260 Series:

192.168.255.1

Gateway

192.168.0.1

Mask

255.255.0.0













-T

Once the login screen is displayed, enter the password in the login password field (use the default

password is “Admin”), and then click the “Submit” button to enter the configuration web page.

Click the “Home”tab to access the DI/DO settings page for the ET-2260 module. This page allows a

simple test to be performed to verify the Digital Input/Output functionality.

In the “Set DO Value”section, check the checkbox for “bit0”to set DO0 to ON.

Click the “Update Settings”button to save the revised settings to the ET-2260 module.



Factory Default

Password: Admin







Once the new settings have been saved, the page will be refreshed to indicate the new values.

Verify that the status for the both DO0 and DI0 is shown as “ON”.

ET-2260 Product Page:

http://www.icpdas.com/root/product/solutions/remote_io/ethernet_io/petl-7000_tpet_tet/et-2260.html

Documentation:

CD:\Napdos\ET2200\Document

http://ftp.icpdas.com/pub/cd/6000cd/napdos/et2200/document/

Firmware:

CD:\Napdos\ET2200\Firmware

http://ftp.icpdas.com/pub/cd/6000cd/napdos/et2200/firmware/

NS-205 and DP-665 Product Page (Optional):

http://www.icpdas.com/root/product/solutions/industrial_ethernet_switch/ns-205.html

http://www.icpdas.com/products/Accessories/power_supply/dp-665.htm



Autres manuels pour ET-2260

Autres manuels ICP DAS USA Unité de contrôle

ICP DAS USA

ICP DAS USA PM-3133i Manuel utilisateur

ICP DAS USA

ICP DAS USA I-7083 Manuel utilisateur

ICP DAS USA

ICP DAS USA PET-7053 Manuel utilisateur

ICP DAS USA

ICP DAS USA SG-3227 Manuel utilisateur

ICP DAS USA

ICP DAS USA ET-7015 Manuel utilisateur

ICP DAS USA

ICP DAS USA WP-5231 Manuel utilisateur

ICP DAS USA

ICP DAS USA I-8123W Guide de configuration

ICP DAS USA

ICP DAS USA ECAT-2061 Manuel utilisateur

ICP DAS USA

ICP DAS USA DS-2200 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA EIP-2000 Series Guide d'installation

ICP DAS USA

ICP DAS USA ZT-2055 Manuel utilisateur

ICP DAS USA

ICP DAS USA LP-8 21 Series Instructions générales

ICP DAS USA

ICP DAS USA EIP-2000 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA PDS-5000 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA 7188EN Guide d'installation

ICP DAS USA

ICP DAS USA LP-8 4 Series Instructions générales

ICP DAS USA

ICP DAS USA I-8088W Manuel utilisateur

ICP DAS USA

ICP DAS USA PM-4324 Series Manuel utilisateur

ICP DAS USA

ICP DAS USA I-2533 Manuel utilisateur

ICP DAS USA

ICP DAS USA ISN-101 Manuel utilisateur

ICP DAS USA

ICP DAS USA DL-10 Manuel utilisateur

ICP DAS USA

ICP DAS USA I-7016 Manuel utilisateur

ICP DAS USA

ICP DAS USA PM-3133-RCT Series Manuel utilisateur

ICP DAS USA

ICP DAS USA PET-7261 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur