Hussmann Q3 Manuel utilisateur

/SPECIALTY 0318

USER MANUAL

SERVICE MERCHANDISER

Q3 VERTICAL BLOWER MEAT

Q3 -Q3-MV-BC-8/StraightVercalCase

 -Q3-MV-BC-12/StraightVercalCase 

Remote

DOE 2012

Energy Eciency

Compliant

Hussmann refrigerated merchandisers congured for sale f

or use in the United States

meet or surpass the requirements of the DOE 2012 energy eciency standards.

Notice 3

General Information 4

Case Sections 5

Installation 6

Unloading

Receiving Case 6

Snapping Chalk Lines 6

Placement 7

Lifting / Panels

Q3MV-BC Lifting and Transport Instructions 8

Front Body Panel Install 9

Fasten Front Body Panel Install 9

Fasten Rear Body Panel Install 9

Leveling

Leveler Adjustment 10

Shim The Case 10

Joining

Parts List 11

Q3-MV-BC Case Adjustments 12

Joining Preparation 15

Refrigeration 18

Piping

Refrigerant 18

Refrigerant piping 18

Line Sizing 18

Oil Traps 18

Refrigeration Spec Sheets 19

Table of Contents

Electrical 20

Electrical Info

Merchandiser Electrical Data 20

Electrical Connections 20

Field Wiring 20

 IdenticationofWiring 20

Remove Rear Raceway 21

Electrical Conduit (Electrical Box) 21

Electrical Wiring Diagram 22

Miatech Fogging System 27

Setup and Installation

Fogging System Mounting 28

Fogger Nozzle Install 28

Water and Air Hose Routing 30

Case Settings 31

Miatech Controller Settings 31

Reverse Osmosis Filter 31

Field Electrical Connections 32

System Clock 34

Fogger System Troubleshooting 37

User Information 38

General

Start Up 38

Load Limits 38

Maintenance

Case Cleaning 41

Exterior Surfaces 41

Interior Surfaces 41

Troubleshooting 43

WARNING

1. DO NOT overload or stand over top of case. Glass breakage may occur if

precautions are disregarded.

*Broken glass can cause lacerations, cuts, and puncture wounds which

may result in severed arteries or tendons, amputations, eye injuries, or

exposure to disease.

Notice

CaseDescripon:

Description: Refrigerated Vertical Blower Meat Service Merchandiser

Shipping Damage: All equipment should be thoroughly examined for shipping damage before and

during unloading. This equipment has been carefully inspected at our factory and the carrier has

assumed responsibility for safe arrival. If damaged, either apparent or concealed, claim must be

made to the carrier Immediately.

Apparent Loss or Damage: If there is an obvious loss or damage, it must be noted on the freight bill

or express receipt and signed by the carrier’s agent; otherwise, carrier may refuse claim. The carrier

will supply necessary claim forms.

Concealed Loss or Damage: When loss or damage is not apparent until after all equipment is

uncrated, a claim for concealed damage is made. Make request in writing to carrier for inspection

within 15 days, and retain all packaging. The carrier will supply inspection report and required claim

forms.

Shortages: Check your shipment for any possible shortages of material. If a shortage should exist

and is found to be the responsibility of Hussmann Chino, notify Hussmann Chino. If such a shortage

involves the carrier, notify the carrier immediately, and request an inspection. Hussmann Chino will

acknowledge shortages within ten days from receipt of equipment.

Hussmann Chino Product Control: The serial number and shipping date of all equipment has been

recordedinHussmann’slesforwarrantyandreplacementpartpurposes.Allcorrespondence

pertaining to warranty or parts ordering must include the serial number of each piece of equipment

involved, in order to provide the customer with the correct parts.

Location/Store Conditions: The Q3-MV-BC refrigerated merchandiser has been designed for use only

in air conditioned stores where temperature and humidity are maintained at 80°F and 55% relative

humidity or 75°F and 55% relative humidity. DO NOT allow air conditioning, electric fans, ovens, open

doors or windows (etc.) to create air currents around the merchandiser, as this will impair its correct

operation.

This equipment is to be installed

to comply with the applicable

NEC, Federal, State , and Local

Plumbing and Construction

Code having jurisdiction.

AT TENTION

INSTALLER

/CHINO

A publication of HUSSMANN®Chino

13770 Ramona Avenue • Chino, California 91710

(909) 628-8942 FAX

(909) 590-4910

(800) 592-2060

Keep this booklet with the case at all times for future reference.

General Information

243/4

(629)

261/2

(673)

231/8

(587)

253/4

(654)

277/8 (708)

1/4

(1327)

12(305)

14(356)

227/8

(581)

153/8

(391)

10 3/8

(264)

251/8

(638) 57/8

(149)

413/8

(1051)

Q3-MV-BC

Multi-Deck Service Deli Case

(203)

Elec

Fogging

System

Drain Refrig

(127) 6 1/8

(156)

End

Panels

11/8

(29)

417/8

(1064)

281/8

(714)

221/8

(562)

251/8

(638)

(1219)

(1829)

(2438)

144

(3658)

Q3-MV-BC

customer side

57/8

(149)

10 3/8

(264)

Case Sections

Installation

NOTICE

Do NOT remove Foam Blocks from shelves

and glass until the merchandisers are

positioned for installation. Shelves or

merchandising glass may be damaged.

Wrapped Top

and Shelves

Foam Blocks

in place

Warning

Labels

Loose

Items

Case is to arrive at store as was shipped form

factory. See reference above for proper shipment

referencing.

Receiving Case

Upon receiving your new Hussmann Case all

equipment should be thoroughly examined for

shipping damage before and during unloading.

This equipment has been carefully inspected at

our factory. Any claim for loss or damage must

be made to the carrier. The carrier will provide

any necessary inspection reports/ or claim form.

If there is obvious loss or damage, it must be

noted on the freight bill or express receipt and

signed by the carrier’s agent; otherwise carrier

may refuse claim.

Snapping Chalk Lines

Preparepermanentpositioningbymarkingoors

with Chalk snap lines where cases are to be

located. Chalk lines are to run along the base or

legs of cases.

Placement

Important: See lifting instructions to properly lift

case when being placed on dollies or permanent

location. (See page 8 for Lifting Instructions.)

First remove Blocks and L Brackets around the

case from pallet.

Remove Block

and L bracket

Proceedbysettingforkliftsunderspeciedloca-

tions as instructed in the Lifting Instructions

(pg. 8.) Be careful not to damage drains or near

components when placing forks underneath

case. A spotter is mandatory to ensure no dam-

age is caused to the case. Lift case and replace

with dollies, place near or in permanent location.

Inser

t Forks

Underneath

Deck

Movethextureascloseaspossibletoitsper-

manent location and then remove all packaging

and preparing to remove off Skid. Remove all

separately packed accessories such as kits, and

Installation (cont’d)

panels. Check for damage before discarding

packaging.

In the case a fork lift truck is not available follow

the demonstration below to properly lift case us-

ing a Johnson Bar (J-Bar) to place on dollies to

trafcfromstartpointtoplacementarea.

Place J-Bar underneath base of merchandiser

to gain leverage, once lifted place Dollie under-

neathrstendandslowlylowerontodollieen-

suring merchandiser is placed on stable location.

Proceed to opposite end and repeat.

Q3-MV-BC Lifting and Transport

Instructions

1. The Q3-MV-BC can be lifted by a forklift at

typical lifting points.

Forklift Points

(Underneathe

Deck)

J-Bar Lift Points

(Underneathe

Base Structure)

J-Bar Lift Points

(Underneathe

Base Structure)

WARNING

Improper placement of forks may damage

drainage piping. Use a spotter when placing

forks. Make sure that piping will not be dam-

aged. Use J-Bars or Jacks if forks cannot be

used safely

2. Ensure lower body panels are removed be-

fore lifting with a forklift. Serious damage will

occur if the body panels are not removed.

3. Make sure that fork spacing and width will not

damage drain or come in contact with piping,

or electrical lines

4. Be sure that the forks are long enough to

support beyond the center of the case but not

damage near components. Check for proper

balance before moving. A minimum fork

length of 36” is recommended for 68” wide

cases

Installation (cont’d)

5. The Q3-MV-BC merchandiser can be raised

at one end underneath the deck with a forklift

to allow the placement of rollers or dollies.

6. Evenly support the entire base structure on

rollers or dollies before attempting to move.

Each Base Leg must have its own dollie to

properly support the case.

Lifting Points are typical and dependent upon

size of case and refrigeration application, drain-

agecongurationswillcallforaltercationsin

Lifting Zones.

Belowarethefollowingdrainagecongurations

and lifting should be altered to the expected

model.

Q3 MV-BC Drain Location

Drain

Installation (cont’d)

Fasten Rear Body Panel Install

(1) Align pre drilled holes to base of case

(2) Secure top and bottom of rear panel using

fasteners as shown below.

Allow front and rear body panels to slide down

resting on support hooks. 2.Place L Bracket

along the underside of deck to hold body panel

top in place against base wall of case.

Front Body Panel Install

A Phillips Screw Driver/Bit will be needed to

install body panels.

To begin Bottom panel assembly place panel A

along side the base of the case and lower panel

on to support hooks along the bottom of the base

(See illustration below for details).

Detail A

Resting Hooks

Panel A

anel B

Fasten Front Body Panel Install

(1) Secure Panel A with top fasteners only.

(2) Overlay Panel B to bottom of Panel A as

shown in illustration below

*Note Panel B will be attached freely with no pre

drilled holes.

Panel A

Panel B

Installation (cont’d)

Leveler Adjustment

Position the case at the highest point. Set a long

magnetized level (4ft [1220 mm] or more) on

either underneath the deck or on top of the case.

Ensure to level case from front to back and side

to side.

Level

(4 ft[1220mm])

Shim The Case

Use shims at each corner of the case to level

out any discrepancies in order to optimize case

performance and proper drainage.

Note: Shims are not Factory supplied. Contractor

should carry available components. Metal Shims

are recommended for use to eliminate any

deterioration from shims over time.

Note:Toavoidremovingconcreteooring,begin

line up levelling from the Highest point of the

storeoor.

NOTICE

Longer length cases may require shims

along the center portion of the case to

maintain proper case performance and

drainage.

Shim

Table des matières

Autres manuels Hussmann marchandiseur

Hussmann

Hussmann SI1N Mode d’emploi

Hussmann

Hussmann IMPACT Excel B4X-E Mode d’emploi

Hussmann

Hussmann Impact C2EC-XLGE Mode d’emploi

Hussmann

Hussmann NM1G Manuel utilisateur

Hussmann

Hussmann VGD Mode d'emploi

Hussmann

Hussmann SMB Manuel utilisateur

Hussmann

Hussmann SMGT Manuel utilisateur

Hussmann

Hussmann Specialty Products CR3HTO-HTB Mode d’emploi

Hussmann

Hussmann M1XLD-GE Mode d’emploi

Hussmann

Hussmann Impact Excel M5X Manuel utilisateur

Hussmann

Hussmann ISFGG Guide rapide

Hussmann

Hussmann IMPACT D5RRI Manuel utilisateur

Hussmann

Hussmann PWREE Manuel utilisateur

Hussmann

Hussmann IMPACT RL Manuel utilisateur

Hussmann

Hussmann Impact C2-XGEP Mode d’emploi

Hussmann

Hussmann IMPACT LWEGH Mode d’emploi

Hussmann

Hussmann Impact Excel C6X-EP Mode d’emploi

Hussmann

Hussmann Impact M3G Manuel utilisateur

Hussmann

Hussmann IMPACT M1DE Manuel utilisateur

Hussmann

Hussmann IMPACT Excel C2-X Manuel utilisateur

Hussmann

Hussmann EcoVision EZ Door Upgrade Manuel utilisateur

Hussmann

Hussmann SSGT Manuel utilisateur

Hussmann

Hussmann C2XEC-XE Mode d’emploi

Hussmann

Hussmann FL5NX-LEP Mode d’emploi

Manuels marchandiseur populaires d'autres marques

FRIGOGLASS

FRIGOGLASS Flex 20 HC Manuel utilisateur

EPTA

EPTA COSTAN RHINO MULTI Manuel utilisateur

CASCO

CASCO Nano Cube Manuel utilisateur

True

True GDIM-26 Manuel utilisateur

Structural Concepts

Structural Concepts Oasis Mobile Series Instructions d'installation

Haussmann

Haussmann RL Manuel utilisateur

Howard McCray

Howard McCray R-CDS32E-4 Manuel utilisateur

EPTA

EPTA iarp Cool Emotions Delight Lite Manuel utilisateur

VALERA

VALERA BC 85 Manuel utilisateur

HL Display

HL Display 3eBin Manuel utilisateur

Dixie Narco

Dixie Narco DNCB 501E Manuel utilisateur

APW Wyott

APW Wyott Racer DMXD-30H Manuel utilisateur

Hoshizaki

Hoshizaki KD-90C Manuel utilisateur

Summit

Summit SCR1006 Manuel utilisateur

Delfield

Delfield Shelleyspeed SPM-28E Manuel utilisateur

EPTA

EPTA iarp Cool Emotions GLEE 40 Manuel utilisateur

Kysor/Warren

Kysor/Warren GranBering KW Mode d’emploi

Crane

Crane BevMAX Refresh 6 Media Manuel utilisateur