Huawei MT992 Manuel utilisateur

MT992 G.fast Modem Quick Start

1Installation

Mounting Your MT992

Horizontal Mounting

Place the MT992 on a smooth surface with cool air and good ventilation. Keep the

MT992 at least 50 mm away from other objects.

Vertical Mounting

1. Mark the positions of two holes used for mounting the MT992, and ensure that

the two holes have the same spacing as the two mounting holes.

2. Select a proper drill according to the outer diameter of the screws. Use a hammer

drill to drill the marked positions on the wall. Then clean the wall and install two

expansion bolts.

3. Use a screwdriver to fasten the screws into the expansion bolts, leaving the heads

of the screws 3 mm over the wall. Then install the MT992 to the screws.

Keep 50 mm clearance on all sides to ensure adequate ventilation.

The figures in this guide are for reference only. The appearance and display

features may vary slightly depending on the actual product version.

31507676_03

Connecting Cables

Connect your devices in the sequence indicated in the following figure.

1 MT992 2 Telephone wall jack 3 Splitter

4 Telephone 5 Router 6 Desktop computer

7 Power adapter 8 Laptop computer

a LINE port b PHONE port c MODEM port

2Powering On

To power on the MT992, press the power button.

After the MT992 is powered on, the MT992 indicator turns on. The following table

lists how the indicators behave when the MT992 is operating properly. If the

indicators do not behave as expected, check whether everything is plugged in

correctly.

When the Internet indicator light turns steady green, you can start browsing the

Internet.

It is recommended that during operation, the MT992 should be more than 1 m away

from electronic devices that can generate 25 kHz to 106 MHz noise, such as

microwave ovens and power line communication modems, and the distance between

the DSL cables and Ethernet cables should be over 10 cm. Noise can affect the access

performance of the MT992, and in extreme cases, it can cause network interruptions.

Indicator Status Description

POWER Steady on The MT992 is powered on and has finished booting.

Off The MT992 is powered off.

DSL Steady on The MT992 is activated through DSL.

Blinking Carrier detection is in progress. (Blinks twice per

second)

The MT992 is being activated through DSL. (Blinks

4 times per second)

Off No connection is set up on the port.

INTERNET Steady on The Routing WAN (TR-069) connection is set up.

Off DSL is activated and the Routing WAN (TR-069)

connection is being set up or has not been set up.

LAN Steady on The MT992 is connected to a device properly.

Blinking Data is being transmitted between the MT992 and

the device connected. (Blinks twice per second)

Off No connection is set up on the port.

NOTE

A software update is in progress when all four indicators blink twice per second.

3Setting the Computer IP Address

Before logging in to the MT992 web page, set the IP address of the computer that

will be used for the login.

On Windows 7

1. Click in the lower right corner of your desktop. Choose Open Network and

Sharing Center.

2. Choose Change adapter settings. Right-click Local Area Connection and

choose Properties.

3. Double-click Internet Protocol Version 4 (TCP/IPv4).

4. Select Use the following IP address. Set IP address to 192.168.1.* (* is any

integer from 2 to 254), Subnet mask to 255.255.255.0, and Default gateway to

192.168.1.1. Click OK to return to the previous dialog box and click OK.

4Logging In to the Web Page

The MT992 provides an intuitive web management page where you can view or set

the MT992 parameters.

1. Open a browser. In the address box, enter 192.168.1.1. Press Enter.

2. Enter the login user name (!!Huawei by default) and password (@HuaweiHgw by

default). Click Login.

3. Enter your current password, and a new password. Re-enter the new password to

confirm it, and click Save.

5Safety Information

This section contains important information about the operation of your device. It

also contains information about how to use the device safely. Read this information

carefully before using your device.

Areas with flammables and explosives

Do not use the device where flammables or explosives are stored (in a gas station,

oil depot, or chemical plant, for example). Using your device in these environments

increases the risk of explosion or fire. In addition, follow the instructions indicated

in text or symbols.

Do not store or transport the device in containers with flammable liquids, gases, or

explosives.

Operating environment

Avoid dusty, damp, or dirty environments. Avoid magnetic fields. Using the device

in these environments may result in circuit malfunctions.

To guard against unauthorized access, change the password after the first login.

When the password is changed successfully, this page will jump to the login page.

Use the user name and new password to log in.

The system will be locked if you input an incorrect user name or password three

consecutive times. One minute later, it will be unlocked.

If you do not perform any operations after logging in to the system for thirty

minutes, you will exit the system and the system will automatically return to the

If you forget the password, you can press and hold the RESET button fo

r 6 seconds or

more, and then the password of the web page will be restored to its factory value.

This operation will cause your own configuration data to be lost. Perform this

operation with caution.

Before connecting and disconnecting cables, stop using the device and disconnect

it from the power supply. Ensure that your hands are dry during operation.

Place the device on a stable surface.

Keep the device away from electronic appliances that generate strong magnetic or

electric fields, such as a microwave oven or refrigerator.

During thunderstorms, power off your device and remove all cables connected to it

to protect against lightning strikes.

Do not use your device during thunderstorms to protect your device against any

danger caused by lightning.

Ideal operating temperatures are 0 °C to 40 °C. Extreme heat or cold may damage

your device or accessories.

Keep the device and accessories in a well-ventilated and cool area away from

direct sunlight. Do not enclose or cover your device with towels or other objects.

Do not place the device in a container with poor heat dissipation, such as a box or

bag.

To protect your device or accessories from fire or electrical shock hazards, avoid

rain and moisture.

Keep the device away from sources of heat and fire, such as a heater, microwave

oven, stove, water heater, radiator, or candle.

Do not place any object, such as a candle or a water container, on the device. If

any foreign object or liquid enters the device, immediately stop using it, power it

off, and remove all cables connected to it. Then, contact an authorized service

center.

Observe local laws and regulations, and respect the privacy and legal rights of

others.

Do not block device openings. Reserve a minimum of 10 cm around the device to

dissipate heat.

Stop using your device or applications for a while if the device is overheated. If skin

is exposed to an overheated device for an extended period, low temperature burn

symptoms, such as red spots and darker pigmentation, may occur.

Do not allow children or pets to bite or suck the device or accessories. Doing so

may result in damage or explosion.

Child's safety

Comply with all precautions with regard to child's safety. Letting children play with

the device or its accessories may be dangerous. The device includes detachable

parts that may present a choking hazard. Keep away from children.

Accessories

Using an unapproved or incompatible power adapter, charger or battery may cause

fire, explosion or other hazards.

Choose only accessories approved for use with this model by the device

manufacturer. The use of any other types of accessories may void the warranty,

may violate local regulations and laws, and may be dangerous. Please contact your

retailer for information about the availability of approved accessories in your area.

Power adapter safety

The power plug is intended to serve as a disconnect device.

For pluggable devices, the socket-outlet shall be installed near the devices and shall

be easily accessible.

Unplug the power adapter from electrical outlets and the device when not in use.

Do not drop or cause an impact to the power adapter. If it is damaged, take it to

an authorized service center for inspection.

If the power cable is damaged (for example, the cord is exposed or broken), or the

plug loosens, stop using it at once. Continued use may lead to electric shocks,

short circuits, or fire.

Do not touch the power cord with wet hands or pull the power cord to disconnect

the power adapter.

Do not touch the device or the power adapter with wet hands. Doing so may lead

to short circuits, malfunctions, or electric shocks.

If your power adapter has been exposed to water, other liquids, or excessive

moisture, take it to an authorized service center for inspection.

Ensure that the power adapter meets the requirements of Clause 2.5 in IEC60950-

1/EN60950-1/UL60950-1 and has been tested and approved according to national

or local standards.

Cleaning and maintenance

During storage, transportation, and operation of the device, keep it dry and

protect it from collision.

Keep the device and accessories dry. Do not attempt to dry it with an external heat

source, such as a microwave oven or hair dryer.

Do not expose your device or accessories to extreme heat or cold. These

environments may interfere with proper function and may lead to fire or explosion.

Avoid collision, which may lead to device malfunctions, overheating, fire, or

explosion.

If the device is not going to be used for an extended period of time, power it off,

and remove all cables connected to it.

If anything unusual occurs (for example, if the device emits smoke or any unusual

sound or smell), immediately stop using it, power it off, remove all cables

connected to it, and contact an authorized service center.

Do not trample, pull, or excessively bend any cable. Doing so may damage the

cable, causing the device to malfunction.

Before you clean or maintain the device, stop using it, stop all applications, and

disconnect all cables connected to it.

Do not use any chemical detergent, powder, or other chemical agents (such as

alcohol and benzene) to clean the device or accessories. These substances may

cause damage to parts or present a fire hazard. Use a clean, soft, and dry cloth to

clean the device and accessories.

Do not dismantle or remanufacture the device and its accessories. This voids the

warranty and releases the manufacturer from liability for damage. In case of

damage, contact an authorized service center for assistance or repair.

Disposal and recycling information

This symbol (with or without a solid bar) on the device, batteries (if

included), and/or the packaging, indicates that the device and its electrical

accessories (for example, a headset, adapter, or cable) and batteries

should not be disposed of as household garbage. These items should not

be disposed of as unsorted municipal waste and should be taken to a

certified collection point for recycling or proper disposal.

For more detailed information about device or battery recycling, contact your local

city office, household waste disposal service, or retail store.

Disposal of the device and batteries (if included) is subject to WEEE Directive Recast

(Directive 2012/19/EU) and Battery Directive (Directive 2006/66/EC). The purpose of

separating WEEE and batteries from other waste is to minimize the potential

environmental impacts and human health risk of any hazardous substances that may

be present.

EU regulatory conformance

Statement

Hereby, Huawei Technologies Co., Ltd. declares that this device is in compliance with

the essential requirements and other relevant provisions of the following Directives:

RoHS Directive 2011/65/EU

LVD Directive 2006/95/EC (until April 19th, 2016) and Directive 2014/35/EU (from

April 20th, 2016)

EMC Directive 2004/108/EC (until April 19th, 2016) and Directive 2014/30/EU (from

April 20th, 2016)

For the declaration of conformity, visit the web site

http://consumer.huawei.com/certification.

The following marking is included in the product:

This device may be operated in all member states of the EU.

Observe national and local regulations where the device is used.

This device may be restricted for use, depending on the local network.

ErP Product Information

Hereby, Huawei Technologies Co., Ltd. declares that the product meets the directive

2009/125/EC and its implementation regulation (EC) NO 1275/2008 amended by (EC)

278/2009, (EC) 642/2009, (EU) 617/2013, (EU) 801/2013, and its implementation

regulation (EC) NO 278/2009.

The power consumption of product in networked standby if all wired network ports

are connected is 5.41 W.

For the product information displayed on the manufacturers' freely accessible

websites required by (EU) No 801/2013, please visit

http://consumer.huawei.com/certification.

No part of this manual may be reproduced or transmitted in any form or by any

means without prior written consent of Huawei Technologies Co., Ltd. and its

affiliates ("Huawei").

The product described in this manual may include copyrighted software of Huawei

and possible licensors. Customers shall not in any manner reproduce, distribute,

modify, decompile, disassemble, decrypt, extract, reverse engineer, lease, assign, or

sublicense the said software, unless such restrictions are prohibited by applicable laws

or such actions are approved by respective copyright holders.

Trademarks and Permissions

, , and are trademarks or registered trademarks of Huawei

Technologies Co., Ltd.

Other trademarks, product, service and company names mentioned may be the

property of their respective owners.

Notice

Some features of the product and its accessories described herein rely on the software

installed, capacities and settings of local network, and therefore may not be activated

or may be limited by local network operators or network service providers.

Thus, the descriptions herein may not exactly match the product or its accessories

which you purchase.

Huawei reserves the right to change or modify any information or specifications

contained in this manual without prior notice and without any liability.

DISCLAIMER

ALL CONTENTS OF THIS MANUAL ARE PROVIDED "AS IS". EXCEPT AS REQUIRED BY

APPLICABLE LAWS, NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED,

INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE, ARE MADE IN RELATION TO THE

ACCURACY, RELIABILITY OR CONTENTS OF THIS MANUAL.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL

HUAWEI BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL

DAMAGES, OR LOSS OF PROFITS, BUSINESS, REVENUE, DATA, GOODWILL SAVINGS

OR ANTICIPATED SAVINGS REGARDLESS OF WHETHER SUCH LOSSES ARE

FORSEEABLE OR NOT.

THE MAXIMUM LIABILITY (THIS LIMITATION SHALL NOT APPLY TO LIABILITY FOR

PERSONAL INJURY TO THE EXTENT APPLICABLE LAW PROHIBITS SUCH A LIMITATION)

OF HUAWEI ARISING FROM THE USE OF THE PRODUCT DESCRIBED IN THIS MANUAL

SHALL BE LIMITED TO THE AMOUNT PAID BY CUSTOMERS FOR THE PURCHASE OF

THIS PRODUCT.

Import and Export Regulations

Customers shall comply with all applicable export or import laws and regulations and

be responsible to obtain all necessary governmental permits and licenses in order to

export, re-export or import the product mentioned in this manual including the

software and technical data therein.

Table des matières

Autres manuels Huawei Modem

Huawei

Huawei E181 HSPA Manuel utilisateur

Huawei

Huawei MS2131I-8 Manuel utilisateur

Huawei

Huawei EchoLife HG510 Manuel utilisateur

Huawei

Huawei B681 Manuel utilisateur

Huawei

Huawei Beeline E1550 Manuel utilisateur

Huawei

Huawei BM632 Manuel utilisateur

Huawei

Huawei E1615 Manuel utilisateur

Huawei

Huawei EchoLife BM635 WiMAX CPE Manuel utilisateur

Huawei

Huawei HG658 Manuel utilisateur

Huawei

Huawei 2degrees Manuel utilisateur

Huawei

Huawei SmartAX MT882a Manuel utilisateur

Huawei

Huawei USB 3G Manuel d'installation et d'exploitation

Huawei

Huawei HiLink E3131 Guide d'installation

Huawei

Huawei E5577 Manuel utilisateur

Huawei

Huawei SoftBank 005HW Manuel utilisateur

Huawei

Huawei E392 Caractéristiques techniques

Huawei

Huawei E392 Manuel utilisateur

Huawei

Huawei EC168 Instructions de montage

Huawei

Huawei E3372 Manuel utilisateur

Huawei

Huawei Globe BROADBAND Manuel utilisateur

Huawei

Huawei Mobile Internet Key Manuel utilisateur

Huawei

Huawei EC150 Manuel utilisateur

Huawei

Huawei Hilink E3276s Manuel utilisateur

Huawei

Huawei E600 Manuel utilisateur

Manuels Modem populaires d'autres marques

Davicom

Davicom DM562AP Manuel utilisateur

EpiValley

EpiValley TATA indicom SXC-1080 Manuel utilisateur

Zte

Zte WiMAX Manuel utilisateur

Intelimax

Intelimax MA-2060 Manuel utilisateur

SMC Networks

SMC Networks D3CM1604V Manuel d'utilisation et d'entretien

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manuel utilisateur

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manuel utilisateur

Samsung

Samsung AceLink SAM-335A Manuel utilisateur

Enfora

Enfora Enabler-G Guide de configuration rapide

iRZ

iRZ ATM2-232 Manuel utilisateur

Zhone

Zhone 6310 Manuel utilisateur

Paradyne

Paradyne Hotwire 7976 Manuel utilisateur

US Robotics

US Robotics 3453C Manuel utilisateur

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manuel utilisateur

Zte

Zte MF823 Manuel utilisateur

Four-Faith

Four-Faith F1403 Manuel utilisateur

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manuel utilisateur

Gemtek

Gemtek WiMAX WIXFBR-103 Manuel utilisateur