HP Surestore 64 - Director Switch Manuel utilisateur
Model A6534A hp surestore director fc-64
Installation Guide
Contents
(A) hp surestore director fc-64 (PN A6534-62001)
(B) Rail Tray Kit (PN A6534-60016):
• Rail tray (1)
• Mounting brackets (2)
• M5 Tinnerman nuts (2)
• Torx T25 16mm M5 SEM screws (4)
(C) Sliding Shelf - only available with the Management
Station (PN J1526-60001):
• Shelf with attached rails (1)
• Mounting brackets (2)
• Torx T25 16mm M5 SEM screws (4)
(D, E, & F) Mounting Hardware:
• Rack mount brackets(PN A6534-60014) containing front
mounting brackets (2), rear mounting brackets (2), and
angle brackets (2)
• Switch rack hardware (PN A6534-62002) containing Torx
T25 16mm M5 SEM screws (22, includes extras), sheet
metal nuts (18), and 10-32 flat-head Phillips screws (8,
includes extras)
Tools Needed:
• Phillips head screwdriver, no.2
• Torx head driver T25
General Information: The 15Us used to mount the switch
are called U1 through U15; U1 is the lowest of the 15Us.
Notice
The information contained in this document is subject to change without
notice.
Hewlett-Packard makes no warranty of any kind with regard to this
material, including, but not limit to, the implied warranties of
merchantability and fitness for a particular purpose. Hewlett-Packard shall
not be liable for errors contained herein or for incidental or consequential
damages in connection with the furnishing performance, or use of this
material.
This document contains proprietary information that is protected by
copyright. All rights are reserved. No part of this document may be
photocopied, reproduced, or translated to another language without the
prior written consent of Hewlett-Packard Company.
H2 of 8
Step 1: Mount the anti-tip feet
(HP Rosebowl II rack only)
Place the anti-tip feet (A) on the front and back of the
rack base. Use the supplied hardware to bolt the feet
to the base of the rack. Be sure to lower the rack feet
(B) until they touch the floor.
Step 2: Select the mounting location for
the rail tray
The rail tray will be mounted 1U below the switch.
Because the switch should be mounted no higher
than U11, the tray should be mounted no higher than
U10. Make sure there are at least 2Us above the top
of the switch empty for the sliding shelf.
3 of 8 H
Step 3: Position and attach the rear
brackets
Locate the lowest U of the 15 you chose for mounting
the switch (the lowest being U1). Attach the rear rail-
tray brackets to the rear rack uprights at U1. Use one
M5 Torx screw for each bracket.
Step 4: Install the Tinnerman nuts on the
front uprights
Install the Tinnerman nuts for the top holes of U1 in
both of the rack’s front uprights.
M5 Screw
with attached
lock washer
HP rack
Rear Tray
bracket
Tinnerman
nut
Outer surface of
HP rack
H4 of 8
Step 5: Insert the rail tray in the rack
Position the rail tray as shown in the following figure
and insert it into the rack from the front. The slots in
the sides of the rail tray must slide over the posts on
the rear rail-tray brackets, and the posts on the rail
tray’s front mounting flanges must be inserted in the
center holes of U1.
Step 6: Secure the rail tray
Insert the M5 Torx screws through the top holes in
both of the rail tray mounting flanges. The screws
pass through the holes in the rack uprights and
thread into the Tinnerman nuts you installed on the
uprights in Step 4. Tighten the screws.
Step 7: Prepare the front rack columns
Standing at the front of the rack, count up from the
top of the rail tray (A) to the 13th, 19th, and 23rd
holes on the rack's front face.
Slide a sheet metal nut (B) on each of the located
holes. You should have three sheet metal nuts on
each front column face (C).
5 of 8 H
Step 8: Prepare the back rack columns
Standing at the back of the rack, count up from the
the top of the rail tray (A) to 12th and 28th on the
rack’s back face.
Slide a sheet metal nut (B) on each of the located
holes. You should have two sheet metal nuts on each
back column face (C).
Step 9: Install the rack mount kit on the
switch
Position the front mounting bracket (A) so that its
angled side faces out and it is on upper part of
switch's side. Using the two center threaded holes on
the front side of the switch, attach the bracket with
flat-head Phillips screws (B). Attach the front
mounting brackets on both sides of the switch.
Position the rear mounting bracket (C) so that its
center holes (D) line up with the first and third
threaded holes on the back portion of the switch's
side. The slotted end (E) of the bracket should face
towards the back of the switch. Using two flat-head
Phillips screws, attach the rear mounting bracket to
the switch. Attach both rear mounting brackets.
H6 of 8
Step 10: Position the switch on the rails
Using a lifting jack, position the switch. Slide the
switch back on the rails until the front mounting
brackets are against the front rack columns.
The use of the Genie Load Lifter is recommended.
Step 11: Mount the switch in the rack
On one side of the back of the switch, position an
angle bracket (A) so that its threaded holes (B) are
against the slots (C) of the rear mounting bracket and
its angled side faces out. Insert the screws (D)
through the rear mounting bracket's slots into the
threaded nuts of the angle bracket. Insert a second
set of screws (E) through the angle bracket and the
rail column into the sheet metal nuts on the back rail
(F).
Repeat the steps above for the other side of the back
of the switch.
At the front of the rack, insert the screws through the
front mounting brackets into the sheet metal nuts that
you installed in the rail columns in Step 7. Tighten the
screws.
7 of 8 H
Step 12: Install the sliding shelf brackets
(Management Station only)
Select a U slot above the switch.
On each back column of the rack, locate the hole (A)
that is 2 holes up from the EIA number of the
selected U slot (B). Line up this hole with the
threaded hole on the bracket's side. Using a screw
(C), attach the rack to the bracket. Attach another
screw (D) loosely in the hole on the inside face of the
bracket (E).
Slide the shelf into the rack. Each rail's back slot (A)
should slide over the loose screws (B) on the
brackets' inside faces.
H8 of 8
Step 12: Install the sliding shelf brackets
(Management Station only) - continued
Make sure that the shelf and rails are horizontal.
Push the rails' front tabs (A) into the corresponding
holes on the rack columns (B).
At the back of the rack, tighten the screws that attach
the shelf rails to the mounting brackets.
Recommended Cable Management
Perform the following instructions after installating
the switch:
• Install two cable restraints on each side of the
rack (A) in positions that will hold the Fibre
Channel cables away from the power supply.
• Form loose bundles of the installed Fibre
Channel cables (B) on the right and left sides.
• On each side, wrap the cable bundles with the
cable restraints in two positions that maintain
clearance for power supply access (C).
H
Copyright 2002
Printed in USA 01/02
A6534-96010
*A6534-960010*
Autres manuels pour Surestore 64 - Director Switch
10
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels HP Stockage
HP
HP StorageWorks NAS 8000 - Version 1.6.X Manuel utilisateur
HP
HP StorageWorks XP1024 Manuel utilisateur
HP
HP SmartMemory Manuel utilisateur
HP
HP C5644A - SureStore Travan T4i Tape Drive Manuel utilisateur
HP
HP P2000 G3 Manuel utilisateur
HP
HP StorageWorks XP1024 Guide rapide
HP
HP Storevirtual 4000 Mode d’emploi
HP
HP Surestore Disk Array 12h - And FC60 Manuel utilisateur
HP
HP StoreEver Series Manuel utilisateur
HP
HP StorageWorks 2000fc Mode d’emploi
HP
HP 7942 Manuel utilisateur
HP
HP OmniBook 3100 - Notebook PC Manuel utilisateur
HP
HP P9000 Manuel utilisateur
HP
HP 20/700 Guide de démarrage rapide
HP
HP LTO-3 960 Instructions d'utilisation
HP
HP StorageWorks 8B - FC Entry Switch Manuel utilisateur
HP
HP StoreAll 8800 Manuel de service
HP
HP Invent Q1575 Series Instructions de montage
HP
HP StorageWorks 2300 - Disk System Manuel utilisateur
HP
HP Surestore Disk Array 12h - And FC60 Instructions de montage
Manuels Stockage populaires d'autres marques
Panasonic
Panasonic LKM-F931-1 Manuel utilisateur
Tabernus
Tabernus Enterprise Erase E2400 Manuel utilisateur
Rocstor
Rocstor COMMANDER 3F series Manuel utilisateur
Western Digital
Western Digital Ultrastar Data60 Manuel utilisateur
Dell
Dell PowerVault MD3600f Series Manuel utilisateur
CFI
CFI TERA STOR SATA RAID IV Manuel utilisateur