HP 20/700 Guide de démarrage rapide
62108 1
HP Surestore Tape Library 20/700
A5605A Expansion Frame Installation Guide
(for HP field service use only)
CAUTION: The HP tape library Expansion Frame is not customer installable or
replaceable. Any servicing, adjustment, maintenance or repair must be performed only
by authorized HP service-trained personnel.
Note to Customer Engineer: This installation may add new technology to the library
that older user’s guides do not address. Please remind the customer that the latest user
documentation is available from the HP Customer Care website: http://www.hp.com/go/
support.
■Materials Included
■Installation Notes
• Confirm with the customer System Administrator that the tape library can be powered
off.
• Observe proper power down and power on procedures, as described in the
Installation or Service Manual.
• If you install or replace an Expansion Module you must check mark the appropriate
box on the Drive Location Label. The Drive Location Label is located on the inside of
the library door, just below the UL label.
•Heavy Load. At least three people are required to remove the Expansion Frame from
packaging and push it into position.
Tools Required
Prior to beginning the installation process, obtain the following tools:
• 1/4-inch Ratchet Wrench
Table 1. Materials List
Part Quantity
I/I Expansion Frame 1
Expansion Frame Assembly 1
1/4-20 x 1/2-in. Torx Screws 6
Lock Down Latch Tool 1
62108 2
■Expansion Frame Install
1. Have the operator take the library and all drives offline and power off the tape library.
2. Obtain key and open cartridge area door.
CAUTION: Lifting hazard. Two people are required to remove the rear cover.
3. Remove the right rear cover (cover with window) by inserting the lock-down latch tool
(see “Special Tools”) between rear cover and the tape library frame on the lower right-hand
side of cover to release cover lock-down latch (see Figure 1).
Figure 1. Removing Right Rear Cover
62108 3
4. Slide cover up and set aside.
5. Using a T30 Torx driver, remove the mushrooms from the tape library frame (6 places) in
the area where the cover was removed (see Figure 1).
6. Position the robotic hand at the top of the Z-column and point it toward the drives.
CAUTION: Be careful not to hit your head on the theta lock down bracket
mounted to the top inside surface of the tape library frame.
7. Using a T15 Torx driver, remove the twelve No. 6-32 x 3/8-in. Torx Pan Head screws
holding the front left plate to the drive tower (see Figure 2). Set the screws and plate aside.
8. If required, remove any customer data cartridges from the cells in Panel 2, Column 3 and
4. Be careful not to damage the cartridges.
Note: The array labels appear directly above the arrays.
9. Remove the array retainer clip and the arrays from Panel 2, Column 3 and 4.
10. Reposition the robotic hand to point to Panel 2, Column 4 (where arrays were removed in
Step 7).
11. Remove theta stop closest to the drives using a flat blade screwdriver (see Figure 2).
Removing Right Rear Cover (a5605a_01)
1. Rear Cover
2. Mushroom (6x)
3. Lock-Down Latch Tool
4. Lock-Down Latch
5. Mushroom (Ref)
6. Mushroom (Ref)
Figure 1. Removing Right Rear Cover (Continued)
62108 4
Figure 2. Theta Stop and Mounting Holes
Theta Stop and Mounting Holes (a5605a_02)
1. Mounting Hole Locations
2. Remove Theta Stop
3. Mounting Hole Locations
4. Measure the distance from the floor to the inside floor of library
5. Front Left Plate
62108 5
CAUTION: Heavy Load. At least three people are required to remove the Expansion
Frame from packaging and push it into position.
12. Remove the expansion frame from its package and place it flat on the floor.
13. Measure the distance from the floor of the room to the inside floor of the tape library (see
Figure 2).
14. Adjust the leveling bolts (4 places) on the expansion frame (measured from the inside
floor of expansion frame to the bottom of the leveling bolt) to be 1/16-inch to 1/8-inch
shorter than what was measured in Step 13.
15. Stand the expansion frame up on the leveling bolts and position it against the frame of the
tape library. Be careful not to bend the leveling bolts when moving the expansion frame
into position.
16. To correctly align the expansion frame with the tape library:
•Align bottom locating pin in expansion frame to the hole in the tape library
floor.
•Align the top locating pin in the expansion frame to the top slot in the tape
library.
•Push the expansion frame firmly against the tape library frame (see Figure 3).
17. While holding the expansion frame in position, adjust the two leveling bolts closest to the
back until they touch the floor (see Figure 3).
62108 6
CAUTION: Be careful not to hit your head on the theta lock down bracket mounted to the
top inside surface of the tape library frame.
18. From the inside of the cartridge area, install six 1/4-20 x 1/2-in. long screws, using a T30
Torx driver, through the holes in the tape library frame into the expansion frame (see
Figure 2 for screw locations) and tighten.
19. Using a T15 Torx driver, reinstall the plate to the left side of the drive using the 12 No.6-
32 screws previously removed in Step 7.
Figure 3. Expansion Frame Alignment
Expansion Frame Alignment (a5605a_03)
1. Top Locating Pin
2. 1/4-20 x 1/2-in. Torx Screw (6x)
3. Expansion Frame
4. Leveling Bolt (4x)
5. Bottom Locating Pin
62108 7
20. Replace the arrays, the array retainer clips, and cartridges removed in Step 7 back to Panel
2, Column 3 and 4.
21. Close the tape library doors and lock.
22. Power the tape library on and verify that it initializes and audits properly.
23. Return unit to customer.
62108
REV C
EC 111700A
Copyright ©2002
Hewlett-Packard Company/
Storage Technology Corp
Edition 1/2002
Autres manuels pour 20/700
2
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels HP Stockage
HP
HP 705 Guide de démarrage rapide
HP
HP Ultrium 232e Manuel utilisateur
HP
HP D5970A - NetServer - LCII Manuel de l'opérateur
HP
HP Invent EH861 Series Instructions de montage
HP
HP StorageWorks XP12000 Manuel utilisateur
HP
HP Storevirtual 4000 Guide de référence rapide
HP
HP storevirtual 3200 Manuel utilisateur
HP
HP StorageWorks 2000fc Mode d’emploi
HP
HP HPE XP P9500 Manuel utilisateur
HP
HP P9000 Manuel utilisateur
HP
HP v275w Manuel utilisateur
HP
HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Mode d’emploi
HP
HP 705 Workstation Manuel utilisateur
HP
HP Surestore DLT 80 Manuel utilisateur
HP
HP High-Performance Secure Hard Disk Manuel utilisateur
HP
HP EVA P6000 Manuel utilisateur
HP
HP XP7 Manuel utilisateur
HP
HP StorageWorks MSA 2/8 - SAN Switch Manuel utilisateur
HP
HP P2000 G3 Manuel utilisateur
HP
HP Data Vault Fiche technique
Manuels Stockage populaires d'autres marques
Panasonic
Panasonic LKM-F931-1 Manuel utilisateur
Tabernus
Tabernus Enterprise Erase E2400 Manuel utilisateur
Rocstor
Rocstor COMMANDER 3F series Manuel utilisateur
Western Digital
Western Digital Ultrastar Data60 Manuel utilisateur
Dell
Dell PowerVault MD3600f Series Manuel utilisateur
CFI
CFI TERA STOR SATA RAID IV Manuel utilisateur