HP StorageWorks 2000fc Mode d’emploi

Page 1

481596-001

About this document

The chassis field replacement unit (FRU) replaces a chassis that has

been damaged or whose midplane has been damaged. To make a

fully functional chassis, you must install the following components

from the replaced chassis:

•Drive modules and air management modules

•Two power-and-cooling modules

•One or two controller modules (for a controller enclosure)

•One or two I/O modules (for a drive enclosure)

This document details procedures for removing drive modules/air

management modules, power-and cooling-modules, controller

modules, and I/O modules from the failed chassis and installing

them into the replacement chassis of an HP StorageWorks 2000

Family Modular Smart Array.

NOTE: Make sure you obtain the latest version of these

instructions from http://www.hp.com/go/msa. Select MSA SAN

Arrays, select your product, and go to Support.

Before you begin

•Turn the power-and-cooling supply modules off and disconnect

the power cables.

•Disconnect and label all cables.

CAUTION: Parts can be damaged by electrostatic discharge.

Use proper anti-static protection:

•Keep the replacement component in the ESD bag until needed.

•Wear an ESD wrist strap grounded to an unpainted surface of

the chassis.

•If an ESD wrist strap is unavailable, touch an unpainted surface

of the chassis before handling the component.

•Never touch connector pins.

Removing drive modules

NOTE: Air management modules are removed and installed

using the same procedure as removing and installing drive modules.

Printed on at least 50% total recycled fiber with at least 10%

post-consumer paper

First edition: March 2008

Product names mentioned herein may be trademarks of their

respective companies as reflected by an associated footnote. The

information in this document is subject to change without notice.

Printed in the US.

www.hp.com

HP StorageWorks

2000 Family Modular Smart

Array

chassis and midplane

replacement instructions

Page 2

1. Press and slide the release latch button to the right to disengage

the latch.

2. Pull the latch out toward the left to disengage the drive module

from the enclosure’s internal connector.

3. Wait 20 seconds for the internal disks to stop spinning, and pull

the drive module out of the enclosure.

Installing drive modules

1. Push the release latch button to the right to open the locking

mechanism.

2. Slide the drive module into the drive slot as far as it will go.

Removing power-and-cooling modules

1. Turn the thumbscrew (1) until it is disengaged from the

power-and-cooling module.

2. Rotate the latch (2) downward to disconnect the power module

from the internal connector, and slide it out from the slot (3).

Installing power-and-cooling modules

1. Slide the power-and-cooling module into the slot as far as it will

go.

2. Press the latch upward to engage the power-and-cooling module;

turn the thumbscrews finger-tight.

Removing controller modules

1. Turn the thumbscrews (2) until the screws disengage from the

controller.

1Release latch button

1Thumbscrew 2Latch

1Latch 2Thumbscrew

12 1 2

Page 3

2. Press both latches downward to disconnect the module from the

midplane.

3. Pull outward on the latches to slide the module out of the

enclosure.

Installing controller modules

1. Loosen the controller’s thumbscrews; press the latches downward.

2. Slide the controller into the enclosure as far as it will go (1).

3. Press the latches upward to engage the controller (2); turn the

thumbscrews finger-tight.

Removing I/O modules

1. Turn the thumbscrews (2) until the screws disengage from the I/O

module.

2. Press both latches downward to disconnect the I/O module from

the midplane.

3. Pull outward on the latches to slide the I/O module out of the

enclosure.

1Latch 2Thumbscrew

Service

12 1 2

Service

Page 4

Installing I/O modules

1. Loosen the controller’s thumbscrews; press the latches downward.

2. Slide the I/O module into the enclosure as far as it will go (1).

3. Press the latches upward to engage the I/O module (2); turn the

thumbscrews finger-tight.

Verifying component installation

•Reconnect cables and power on the system and associated data

host in the following order:

a. Drive enclosure first

b. Controller enclosure next

c. Data host last

•On the power-and-cooling modules, check that the AC Power

Good LED (top) is on.

•On the controller and I/O modules, check that the OK LED

(back) illuminates green, indicating that the module has

completed initializing and is online.

Additional information

See the MSA web site: http://www.hp.com/go/msa.

Service

Autres manuels pour StorageWorks 2000fc

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels HP Stockage

HP StoreEver MSL4048 Manuel utilisateur

HP XP20000/XP24000 Manuel utilisateur

HP PD5000Z Manuel utilisateur

HP StorageWorks DAT320 USB Mode d’emploi

HP P9000 Manuel utilisateur

HP StorageWorks 600 - Modular Disk System Manuel

HP 3000 - 37XE System Mode d’emploi

HP StorageWorks XP10000 - Disk Array Manuel utilisateur

HP Invent Q1573 Series Instructions de montage

HP StorageWorks 8B - FC Entry Switch Manuel utilisateur

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Mode d’emploi

HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard... Mode d’emploi

HP EY904AA - Personal Media Drive 160 GB External... Manuel utilisateur

HP ESL E-Series Manuel utilisateur

HP StoreOnce B6000 Manuel utilisateur

HP StorageWorks 2405 - Disk System Manuel de la liste des pièces

HP StorageWorks TL895 Manuel utilisateur

HP Surestore 6164 - Switch Manuel utilisateur

HP VS80 - StorageWorks DLT VS 80 Tape Drive Manuel utilisateur

HP StorageWorks ESL9322S2 Manuel utilisateur

HP P9000 Manuel utilisateur

HP 8505 8mm Cartridge Tape Drive EK-STWCT-UG.... Manuel utilisateur

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Mode d’emploi

HP StorageWorks 8000 - NAS Manuel d'installation

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur

Dell

Dell PowerVault MD3600f Series Manuel utilisateur

CFI

CFI TERA STOR SATA RAID IV Manuel utilisateur