HP StorageWorks 2000fc Mode d’emploi

Page 1

481593-001

About this document

This document details procedures for replacing a failed controller

module in an HP StorageWorks 2012fc Modular Smart Array.

NOTE: Make sure you obtain the latest version of these

instructions from http://www.hp.com/go/msa. Select MSA SAN

Arrays, select your product, and go to Support.

Before you begin

CAUTION: When replacing a controller, ensure that less than

10 seconds elapse between inserting the controller into a slot and

fully latching it in place. Failing to do so might cause the controller

to fail. If it is not latched within 10 seconds, remove the controller

from the slot and repeat the process.

Parts can be damaged by electrostatic discharge. Use proper

anti-static protection:

•Keep the replacement component in the ESD bag until needed.

•Wear an ESD wrist strap grounded to an unpainted surface of

the chassis.

•If an ESD wrist strap is unavailable, touch an unpainted surface

of the chassis before handling the component.

•Never touch connector pins.

Using the Storage Management Utility (SMU), save your

configuration settings to a file for backup.

1. Select Manage > Utilities > Configuration Utilities > Save Config

File.

2. Click Save Configuration File.

In a dual-controller configuration, the storage system’s Partner

Firmware Upgrade option is enabled by default, so when you

upgrade a controller the system automatically ensures that both

controllers have the most recent version.

Use SMU to verify that Partner Firmware Update is enabled.

1. Select Monitor > Status > Advanced Settings > Misc

Configuration to view the current setting.

2. If Partner Firmware Upgrade is disabled, select Manage >

General Config > System Configuration, and then set Partner

Firmware Upgrade to Enabled.

Verifying component failure

Use the following methods to verify component failure:

•Check Fault/Service Required LED (back):

• Amber = Fault condition

•Check that the OK LED (back) is off.

•Check the event log for errors.

Removing the controller module

1. In a dual-controller configuration, verify that the partner

controller is online by selecting Monitor > Status > Status

Summary.

2. Shut down the failed controller.

a. Select Manage > Restart System > Shut Down/Restart, and

select a controller option.

b. Click Shut Down and click OK.

The blue OK to Remove LED (back) illuminates to indicate that

the controller can be removed safely.

Printed on at least 50% total recycled fiber with at least 10%

post-consumer paper

First edition: March 2008

Product names mentioned herein may be trademarks of their

respective companies as reflected by an associated footnote. The

information in this document is subject to change without notice.

Printed in the US.

www.hp.com

HP StorageWorks

2012fc Modular Smart Array

controller module replacement

instructions

Page 2

3. Illuminate the UID (Unit Identification) LED of the enclosure that

contains the controller module to remove.

a. Select Manage > General Config > Enclosure Management.

b. Click Illuminate Locator LED.

4. Locate the enclosure whose UID LED (front right ear) is blue, and

within it, the controller module whose OK to Remove LED is blue.

5. Disconnect any SAS cables that connect the controller to a drive

enclosure.

6. Turn the thumbscrews (2) until the screws disengage from the

controller.

7. Press both latches downward to disconnect the module from the

midplane.

8. Pull outward on the latches to slide the module out of the

enclosure.

Installing the controller module

NOTE: You can install a controller into an enclosure that is

powered on.

1. Loosen the controller’s thumbscrews; press the latches downward.

2. Slide the controller into the enclosure as far as it will go (1).

3. Press the latches upward to engage the controller (2); turn the

thumbscrews finger-tight.

4. Reconnect the SAS cables.

IMPORTANT: In a dual-controller configuration, if the

firmware versions differ between the two controllers, Partner

Firmware Upgrade brings the older firmware to the later firmware

level.

Verifying component replacement

After replacing the controller, check that the OK LED (back)

illuminates green, indicating that the controller has completed

initializing and is online.

If the enclosure’s UID is on, use SMU to turn it off.

1. Select Manage > General Config > Enclosure Management.

2. Click Turn Off Locator LED.

If the Fault/Service Required LED is amber, the module has not gone

online and likely failed its self-test. Put the module online by

following the steps to restart a controller or by checking the event

log for errors.

Additional information

See the MSA web site: http://www.hp.com/go/msa.

1Latch 2Thumbscrew

12 1 2

Autres manuels pour StorageWorks 2000fc

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels HP Stockage

HP MSL4048 - StorageWorks Ultrium 920 Tape... Mode d’emploi

HP StorageWorks 2000fc Manuel utilisateur

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Mode d’emploi

HP v119r Manuel utilisateur

HP StorageWorks 2000fc Mode d’emploi

HP StorageWorks P4000 Series Manuel utilisateur

HP StorageWorks 8B - FC Entry Switch Manuel utilisateur

HP D2D Manuel utilisateur

HP Compaq Presario,Presario 2120 Manuel utilisateur

HP px3100 Manuel utilisateur

HP StorageWorks 2405 - Disk System Manuel utilisateur

HP 6400/8400 Manuel utilisateur

HP C7401A - SureStore Ultrium 230 Tape Drive Manuel du produit

HP HPE StoreEver LTO-8 Ultrium Tape Manuel du produit

HP AJ750A - StorageWorks Modular Smart Array 2000 Dual I/O Storage... Mode d’emploi

HP StoreOnce D2D2500 Manuel utilisateur

HP ProLiant StorageWorks NAS 1500s Manuel utilisateur

HP A2W75-67905 Manuel utilisateur

HP 7957A Manuel utilisateur

HP StorageWorks NAS b2000 - v2 Manuel utilisateur

HP C450W Mode d’emploi

HP Compaq Presario,Presario 4400 Mode d’emploi

HP D2D Manuel utilisateur

HP StorageWorks RDX160 Instructions d'utilisation

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur

Dell

Dell PowerVault MD3600f Series Manuel utilisateur

CFI

CFI TERA STOR SATA RAID IV Manuel utilisateur