HP ProCurve 1600M Manuel utilisateur

HP ProCurve Switch Quick Setup Guide

These images are examples only. Your switch may look a little different.

➊Unpack and check included parts:

•Switch

• Switch Quick Setup Guide

• Read Me First

• Safety and Regulatory booklet

• Customer Support/Warranty booklet

•Consolecable

• Accessory kit

• Power cord

➋Prepare for installation.

To avoid personal injury or product damage, review

the installation guidelines on the next page.

➌Verify selftest by connecting the power cord.

➍Install mounting brackets.

➎Mount the switch and connect the power cord.

➏(Optional) Connect console cable.

➐Configure (minimal configuration).

➑Connect network cables.

For more installation information refer to the Installation

and Getting Started Guide for your product, located on

the HP ProCurve Web site at:

www.procurve.com/manuals.

Note: Before installing the switch in a rack, check the

Installation and Getting Started Guide for specific rack

installation instructions.

Port LEDs

Test LED

Power and

Fault LEDs

Console

cable

To PC

By default, the switch is configured to acquire an IP address config-

uration from a DHCP or Bootp server.

For more information on configuration and remote management, see

the Management and Configuration Guide for your switch, which is

on the ProCurve Web site at www.procurve.com/manuals.

RJ-45

connector

Fiber cable

connector

Installation Guidelines

To avoid personal injury or product damage when installing your switch, read the installation precautions and

guidelines below.

For Safety and Regulatory information refer to the Safety and EMC Regulatory booklet included with the switch.

Installation Precautions

Warnings

■The rack or cabinet should be adequately secured to prevent it from becoming unstable and/or falling

over.

■Devices installed in a rack or cabinet should be mounted as low as possible, with the heaviest devices

at the bottom and progressively lighter devices installed above.

■Do not wall mount any switch without checking for restrictions in the Installation and Getting

Started Guide.

Cautions

■If the switch is to be shipped in a rack, be sure to use only an HP 10K rack. Mount the switch using rail kit part

number 356578-B21 and shelf kit AB469A. Both kits must be used. Otherwise you will void the switchwarranty.

■Ensure the power source circuits are properly grounded, then use the power cord supplied with the switch to

connect it to the power source.

■If your installation requires a different power cord than the one supplied with the switch and power supply, be

sure the cord is adequately sized for the switch’s current requirements. In addition, be sure to use a power cord

displaying the mark of the safety agency that defines the regulations for power cords in your country. The mark

is your assurance that the power cord can be used safely with the switch and power supply.

■When installing the switch, the AC outlet should be near the switch and should be easily accessible in case the

switch must be powered off.

■Ensure the switch does not overload the power circuits, wiring, and over-current protection. To determine the

possibility of overloading the supply circuits, add together the ampere ratings of all devices installed on the

same circuit as the switch and compare the total with the rating limit for the circuit. The maximum ampere

ratings are usually printed on the devices near the AC power connectors.

■Do not install the switch in an environment where the operating ambient temperature exceeds its specification.

■Ensure the air flow around the switch is not restricted. Leave at least 3 inches (7.6 cm) for cooling. For the air

flow direction, see the Installation and Getting Started Guide for your product, located on the HP ProCurve

Web site at www.procurve.com/manuals.

Part Number: 5992-4964

November 2008

Printed in Singapore

*5992-4964*

Development Company, L.P.

The information herein is subject to

change without notice.

Autres manuels pour ProCurve 1600M

Table des matières

Autres manuels HP Matériel réseau

HP ProCurve Radio Port 230 Instructions de montage

HP Edgeline EL1000 Manuel utilisateur

HP AdvanceNet 30244M Manuel

HP AHA-8940 Manuel utilisateur

HP AJ878A - StorageWorks 320 GB Hard Drive Manuel utilisateur

HP FlexNetwork 6616 Manuel utilisateur

HP Bc1500 - BladeSystem - Blade PC Manuel

HP In/Out P2P 10/13dBi MIMO 3 Instructions de montage

HP UPS Network Module Manuel utilisateur

HP J9666A Manuel utilisateur

HP E-MSM466-R Instructions de montage

HP JG602A Manuel utilisateur

HP Mv2120 - Media Vault Network Drive Manuel utilisateur

HP IBRIX X9000 Manuel utilisateur

HP MSA 2040 Manuel utilisateur

HP 205H-MNT2 Manuel utilisateur

HP ProCurve 8116fl Instructions de montage

HP 30020B Manuel

HP Aruba 640 Instructions de montage

HP 201723-B21 - HP StorageWorks Modular SAN Array 1000 Hard... Manuel utilisateur

HP D7171A - NetServer - LPr Manuel utilisateur

HP StorageWorks AB466A Manuel utilisateur

HP 4265B Manuel de service

HP StorageWorks T5521A Manuel

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur