Honeywell Excel 15 W7760A Manuel utilisateur

Excel 15 W7760A

EPROM REPLACEMENT

DESCRIPTION 5. Remove galvanized plate. Place on adjacent work

This EPROM Replacement procedure outlines the surface in the orientation as it was removed

process to upgrade the Excel 15 W7760A Controller to

the latest firmware release.

Firmware replacement kit: Part # 32004159-002 Plate

Procedure will apply to future firmware as released. Work Surface

Material Needed

1. Replacement EPROM. Programmed with new Firmware Side View

2. #10 Tork Driver (preferred), or 3/16" thin flat-blade

screwdriver 6. Set aside paper protective sheet, then remove 2 screws

that secure board to cover.

3. Extraction Tool: AMP PLCC Extraction Tool 821903-50

00, AMP 822154-1 00, or small diameter probe/object

(i.e. paper clip)

Procedure

1. Discharge static electricity form body by touching known

earth ground. 7. Making certain you are grounded. Remove the circuit

2. Remove W7760A from wiring subbase. Place controller board and place it component side up, pin side down on

on work surface with pins and label side up. top of the galvanized plate. Extend pins over the edge

on each side of the galvanized plate.

3. Remove plastic, anti-static sheet. (This sheet contains

device information) – Set aside.

Caution: Do not tear plastic protective sheet at

corners.

oard

Plate

4. Using the #10 Tork Driver or flat-bladed screwdriver

remove the four screws around perimeter. Put the

screws aside in a secure place for later re-assembly. Work Surface

Side View

®U.S. Registered Trademark

95- 7631

Excel 15 W7760A EPROM Replacement

REPLACEMENT

PROM

Note: Orient the board with heat sink to

left. The EPROM to be replaced is the

socketed component located closest to

the component labeled Echelon Heat Sink

Home and Building Control Home and Building Control Home and Building Control Products

Honeywell Inc. Honeywell Limited-Honeywell Limitee Honeywell AG

Honeywell Plaza 155 Gordon Baker Road Böblinger Straße 17

P.O. Box 524 North York Ontario D-71101 Schönaich

Minneapolis, MN 55408-0524 M2H 3N7 Phone (49-7031) 637-01

Fax (49-7031) 637-493

Echelon

Jack

8. Insert the tips of the Extraction Tool in the diagonal slots of the micro socket, and slowly remove the EPROM with a

rocking motion.

9. Again, making certain you are grounded, insert the new EPROM into the socket, orienting the notch in the chip with the

notch in the socket in the lower right hand corner. The EPROM may be inserted into the socket by placing it on top of the

socket and pressing it into place with thumb pressure until it is seated. While pressing the EPROM into the socket, keep

another finger on the rear of the circuit board behind the socket so the board is not stressed while pressing with the thumb.

10. Turn the circuit board upside down again and orient it on the cover. Replace the two center screws.

11. Replace the protective paper and the galvanized plate. Replace the 4 screws in each corner.

12. Replace the labeled plastic sheet.

13. Keep EPROM in a safe place until system operation has been confirmed.

14. Make a record of the W7760A as being updated. It is good idea to make a mark on the controller to that effect as well.

15. Reinstall the W7760A.

Printed in U.S.A. on recycled

paper containing at least 10%

95-7631 D.B. 12-99

post-consumer paper fibers.

www.honeywell.com

Autres manuels Honeywell Contrôleurs

Honeywell

Honeywell HON 5020 Manuel utilisateur

Honeywell

Honeywell CVL4022ASVAV1 Manuel utilisateur

Honeywell

Honeywell S4965V3250 Instructions d'utilisation et d'installation

Honeywell

Honeywell HVC0002 Manuel utilisateur

Honeywell

Honeywell SLATE Manuel utilisateur

Honeywell

Honeywell HCE 60 Manuel du propriétaire

Honeywell

Honeywell 40014 Manuel utilisateur

Honeywell

Honeywell MP909E Fiche technique

Honeywell

Honeywell dcp100t Manuel utilisateur

Honeywell

Honeywell Aquastat L7224U Manuel utilisateur

Honeywell

Honeywell L7124U Manuel utilisateur

Honeywell

Honeywell S9200U1000 Manuel utilisateur

Honeywell

Honeywell B Manuel utilisateur

Honeywell

Honeywell AQUASTAT L4188A Manuel utilisateur

Honeywell

Honeywell 190797-YAD Manuel utilisateur

Honeywell

Honeywell WEB/CP-202-XPR Manuel utilisateur

Honeywell

Honeywell R8182D Manuel d'utilisation

Honeywell

Honeywell HercuLine 2000 Series Manuel utilisateur

Honeywell

Honeywell DKG 972 Manuel utilisateur

Honeywell

Honeywell 301C Manuel utilisateur

Honeywell

Honeywell S9361A207 Series Manuel utilisateur

Honeywell

Honeywell T775M Manuel du propriétaire

Honeywell

Honeywell LYNX Touch L5200 Series Manuel utilisateur

Honeywell

Honeywell R7184A Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur