Honeywell T775M Manuel du propriétaire
To program the controller, perform the following procedures in the order listed:
Fig. 1
Press the MENU button, then select PROGRAM and press the button to view the
program menu.
Fig. 1 shows the Program menu for controller.
Fig. 2
1. From the menu, use the and buttons to highlight MOD 1.
2. Press the button to select MOD 1 to view the parameters. Fig. 2 shows
RELAY 1. In MOD 1, THROT RNG replaces DIFFERNTL.
!"#
Fig. Program – Setpoint
1. From the menu, use the and buttons to highlight SETPOINT.
2. Press the button to display the setpoint value.
3. Use the and buttons to increase/decrease the desired setpoint
temperature.
Set the temperature to 55°F.
4. Press the button to accept the setpoint temperature and display the next
option.
!"$%&'!"$&"$
Fig. Program – Throttling Range
1. From the menu, use the and buttons to highlight THROT RNG.
2. Press the button to display the throttling range value.
3. Use the and buttons to increase/decrease the desired value.
Set the value to 10°F.
4. Press the button to accept the value and display the next option.
( " &
Fig. Program – Sensor
1. From the menu, use the and buttons to highlight SENSOR.
2. Press the button to display the sensor selections.
3. Use the and buttons to select Sensor A or B.
Select sensor B.
4. Press the button to accept the highlighted sensor and display the next option.
)%*'
Fig. Program Heat/Cool
1. From the menu, use the and buttons to highlight HEAT/COOL (Default:
HEAT).
2. Press the button to display the heat and cool selections.
3. Use the and buttons to select Heat or Cool.
Select COOL.
4. Press the button to accept the highlighted selection and display the next
option.
+
Press the button to accept the highlighted selection EXIT. This will display the main
Program Menu screen (Fig. 1)
Fig. 1
("+,#-
1. From the menu, use the and buttons to highlight MOD 2.
2. Press the button to select MOD 2 to view the parameters.
( !"#
Fig. Program - Setpoint
1. From the menu, use the and buttons to highlight SETPOINT.
2. Press the button to display the setpoint value.
3. Use the and buttons to increase/decrease the desired setpoint
temperature.
Set the temperature to 55°F.
4. Press the button to accept the setpoint temperature and display the next
option.
( !"$%&'!"$&"$
Fig. Program – Throttling Range
1. From the menu, use the and buttons to highlight THROT RNG.
2. Press the button to display the throttling range value.
3. Use the and buttons to increase/decrease the desired value.
Set the value to 10°F.
4. Press the button to accept the value and display the next option.
(( " &
Fig. Program – Sensor
5. From the menu, use the and buttons to highlight SENSOR.
6. Press the button to display the sensor selections.
7. Use the and buttons to select Sensor A or B.
Select sensor A.
8. Press the button to accept the highlighted sensor and display the next option.
()%*'
Fig. Program Heat/Cool
5. From the menu, use the and buttons to highlight HEAT/COOL (Default:
HEAT).
6. Press the button to display the heat and cool selections.
7. Use the and buttons to select Heat or Cool.
Select HEAT.
8. Press the button to accept the highlighted selection and display the next
option.
_____________________________________________________________________
(+
Press the button to accept the highlighted selection EXIT. This will display the main
Program Menu screen (Fig. 1)
Fig. 1
)"+,&'.-
1. From the menu, use the and buttons to highlight RELAY 1.
Fig. 2
2. Press the button to select RELAY 1 to view the parameters.
) !"&'.
Fig. Program - Setpoint
1. From the menu, use the and buttons to highlight SETPOINT (Fig. 2).
2. Press the button to display the setpoint value.
3. Use the and buttons to increase/decrease the desired setpoint
temperature.
Set the temperature to 100°F.
4. Press the button to accept the setpoint temperature and display the next
option.
_____________________________________________________________________
)#!&"!' !"$
Fig. Program – Differential
1. From the menu, use the and buttons to highlight DIFFERNTL.
2. Press the button to display the differential value.
3. Use the and buttons to increase/decrease the desired value.
Set the value to 10°F.
4. Press the button to accept the value and display the next option.
)( " &
Fig. Program – Sensor
1. From the menu, use the and buttons to highlight SENSOR.
2. Press the button to display the sensor selections.
3. Use the and buttons to select Sensor A or B.
Select sensor A.
4. Press the button to accept the highlighted sensor and display the next option.
))%*'
Fig. Program Heat/Cool
1. From the menu, use the and buttons to highlight HEAT/COOL (Default:
HEAT).
2. Press the button to display the heat and cool selections.
3. Use the and buttons to select Heat or Cool.
Select HEAT.
4. Press the button to accept the highlighted selection and display the next
option.
+
Fig. Program – Exit
Press the HOME button to leave programming mode and return to the home screen.
This completes the programming procedure.
Table des matières
Autres manuels Honeywell Contrôleurs
Honeywell
Honeywell MN7220 Manuel d'utilisation
Honeywell
Honeywell T775U2006 Manuel utilisateur
Honeywell
Honeywell ScanDome HTX-5000 Manuel utilisateur
Honeywell
Honeywell Aquasat L7224 A Aquasat L7224 C Manuel utilisateur
Honeywell
Honeywell TUXWIFIS Manuel utilisateur
Honeywell
Honeywell HR 40 Manuel utilisateur
Honeywell
Honeywell Excel 10 W7751H Manuel utilisateur
Honeywell
Honeywell S4565 Series Manuel utilisateur
Honeywell
Honeywell Fire Sentry FS7-130-SX Manuel utilisateur
Honeywell
Honeywell T2798I2000 Manuel utilisateur
Honeywell
Honeywell MP953A Manuel d'utilisation
Honeywell
Honeywell WEB/CP-202-XPR Manuel utilisateur
Honeywell
Honeywell DCP 250 Guide d'installation
Honeywell
Honeywell 7800 SERIES Manuel utilisateur
Honeywell
Honeywell LCBS Connect Instructions d'utilisation
Honeywell
Honeywell Experion C300 Manuel utilisateur
Honeywell
Honeywell Experion PKS Manuel d'instructions
Honeywell
Honeywell UDC2000 Manuel utilisateur
Honeywell
Honeywell 5000 Series Manuel utilisateur
Honeywell
Honeywell HON 372 Manuel
