Honeywell Fire-lite FFT Manuel utilisateur

FFT

Fire Fighter Telephone Module

Product Installation Drawing

Document 52246 RevA 1/16/08 ECN 07-873

CAUTION! Make sure to observe all of the following precautions:

• Remove all power (AC and DC) before installing or removing any modules since damage to components

may occur if power remains applied.

• Circuit boards contain static-sensitive components. Always ground yourself with a proper wrist strap

before handling any boards so that static charges are removed from the body. Use static suppressive

packaging to protect electronic assemblies.

FFTReplacement

1. Make certain thatAC and DC power have been removed from the panel.

2. Unplug the terminal block connectors from TB1, TB2 and TB3 located on the top edge of the defective FFT board

(label to ensure reinstallation in correct positions).

3. Unplug the panel telephone handset from Phone Jack J1 located on bottom center of the defective FFT board.

4. Remove two mounting screws which hold the defective FFT board to the mounting bracket standoffs and set aside.

5. Carefully lift the defective FFT board from the slot in the bottom of the mounting bracket.

6. Remove the ribbon cable connectors from J2 on the right side of the board and J3 on the back of the defective FFT

board.

7. Connect cable between J2 on the new FFTboard and P5 on Zone Split Audio Panel main circuit board as illustrated

below.

8. If telephone call-ins are to be annunciated on the ZPM, connect cable between J3 on the FFT and P4 on the back

of the ZPM(K) module. Note that the J3 and P4 ribbon cable connectors are keyed to prevent incorrect

installation. Refer to following illustration for connector locations.

The FFTFire Fighter Telephone Module provides supervision,

annunciation and control for local and remote telephone handsets as

well as an optional remote microphone.

Audio Panel with Zone Split

Make certain that the ribbon cable is

installedwith thered stripeoriented

asillustrated below.

red stripe

Document 52246 RevA ECN 07-873 1/16/08

Standoff Standoff

Slot

Mounting Bracket

FFT

Terminal Block Connectors

J2 (on side)

TB1TB2TB3

J3 (on back)

RibbonCable

Connectors

SW1 J1

9. Insert the bottom of the new FFT board in the slot located in the bottom right of the mounting bracket as indi-

cated in illustration below.

10. Secure the module to the mounting bracket standoffs with the two mounting screws.

11. Wire the terminal blocks TB1,TB2 and TB3 as described in the illustration below. Plug the terminal block

connectors which were disconnected in step 2 into TB1, TB2 andTB3 located on the top edge of the FFT.

12. Plug the panel telephone handset into Phone Jack J1 on bottom center of FFT.

13. Set switch SW1 to correct position. SW1 positioned to the left (as illustrated below) indicates that the remote

microphone is installed. SW1 positioned to the right indicates that a remote microphone is not installed.

14. Set switch SW2 to correct position. SW2 positioned up (as illustrated below) indicates that the audio wiring to

the Remote Page Jack is configured for 2-wire Class B.

15. ReapplyAC and DC power

16. Program the host FACPfor proper operation with the Audio Panel

17. Test the panel for proper operation.

SW2

Table des matières

Autres manuels Honeywell Unité de contrôle

Honeywell

Honeywell W7212 Manuel d'utilisation

Honeywell

Honeywell ControlEdge 900 platform Manuel utilisateur

Honeywell

Honeywell FIRE-LITE ALARMS CRF-300 Manuel utilisateur

Honeywell

Honeywell FIRE-LITE-ALARMS CMF-300 Manuel utilisateur

Honeywell

Honeywell LYNX Series Manuel utilisateur

Honeywell

Honeywell SILENT KNIGHT SK-FML Manuel utilisateur

Honeywell

Honeywell HumidiPRO H6062A1000/U Manuel utilisateur

Honeywell

Honeywell 7800 SERIES Manuel utilisateur

Honeywell

Honeywell Notifier FCM-1 Manuel utilisateur

Honeywell

Honeywell HM700AFVALVE Manuel utilisateur

Honeywell

Honeywell Braukmann D06G Manuel utilisateur

Honeywell

Honeywell PS300 Manuel utilisateur

Honeywell

Honeywell VC Series Manuel utilisateur

Honeywell

Honeywell PFA 700 Manuel

Honeywell

Honeywell CentraLine CLCM1T Manuel utilisateur

Honeywell

Honeywell 4286 Guide de configuration

Honeywell

Honeywell RV280 Manuel utilisateur

Honeywell

Honeywell BA295S Manuel utilisateur

Honeywell

Honeywell S7800A Manuel utilisateur

Honeywell

Honeywell Aquatrol W964F Manuel du propriétaire

Honeywell

Honeywell RMG 213 Mode d’emploi

Honeywell

Honeywell RV181 Manuel utilisateur

Honeywell

Honeywell EIM Guide d'installation

Honeywell

Honeywell Braukmann RV 284 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur