Honeywell EIM Guide d'installation

Equipment Interface Module

Training

EIM Module Basics

•Reasons to use EIM Modules:

1.)Not enough wires to thermostat or want to use

wireless thermostat.

2.)Want to monitor system through honeywell

3.)Installing a humidifier, ventilator, dehumidifier

4.)Use of dry contacts for alarms, alerts, unit

protection.

EIM Module Mounting Locations

•1.)Mounting EIM Module on horizontal

applications can be accomplished by mounting to

supply or return air plenums.

•2.)Mounting EIM Module on vertical applications

can be accomplished by mounting to supply

ductwork or walls in closet.

•3.)Mounting EIM Module on package units can be

accomplished by installing anywhere inside unit

where water can not enter. Examples: mount on

splitter inside, interior wall, heat strip

compartment.

EIM Module Wiring

•1.) If wiring 24 volts to thermostat Red and

Common to be connected at R and C at the

(TO THERMOSTAT) terminals on EIM Module.

•2.)Wiring to equipment is standard

connections: example Y to Y, G to G on EIM

Module terminals.

•3.) Wiring of discharge sensor to go to S2

terminals on EIM Module, note does not

matter which wire goes to which.

EIM Module Wiring Cont

•4.) Wiring of return air sensor to be connected to

S1 terminals on EIM Module, note does not

matter what wire goes to which terminal.

•5.)Wiring of condensate safety switch must be

connected to the S3 terminals, again does not

matter which wires.

•6.)Wiring of drain pan sensor (optional) must be

connected to S4 terminals for normally closed

circuit, and 24 volts to Red and Common

Programming Redlink for EIM Module

•1.)Follow instructions that come up on screen when

new thermostat is first installed or reset to factory

default settings then follow instructions.

•2.)Go through thermostat until thermostat reads:T-Stat

Controls an Equip Module:NO switch using arrow keys

to yes. Next hit yes then next says to press connect at

EIM Module. Press connect and wait to see green LED

start flashing then go to thermostat and hit next.

Should say connecting, once connected thermostat will

say connected, hit next and you have now linked

thermostat to Module.

Programming Continued

•3.)Next screen on thermostat says connect

redlink devices, this is where you connect all

wireless devices.

•4.)Continue through set up until thermostat

says:Wired Sensor on S terminals:no. Switch

to yes using arrow keys and hit next.

•5.)Next screen asks if wired remote indoor

sensor:no leave at no these are not remote

indoor sensors.

Autres manuels Honeywell Unité de contrôle

Honeywell

Honeywell VR8305 Manuel utilisateur

Honeywell

Honeywell Krom Schroeder VAN Series Manuel utilisateur

Honeywell

Honeywell Velociti Series Manuel utilisateur

Honeywell

Honeywell MasterLogic 50 Series Manuel utilisateur

Honeywell

Honeywell ADEMCO 5800RL Instructions de montage

Honeywell

Honeywell TR70 Manuel utilisateur

Honeywell

Honeywell RA116A Manuel utilisateur

Honeywell

Honeywell MI-DCMOE Mode d’emploi

Honeywell

Honeywell VC Series Manuel utilisateur

Honeywell

Honeywell L5000-Wi-Fi Manuel utilisateur

Honeywell

Honeywell A4021 Series Manuel utilisateur

Honeywell

Honeywell ERM5220R1018 Manuel utilisateur

Honeywell

Honeywell Notifier NFG-8 Manuel utilisateur

Honeywell

Honeywell RA890F Protectorelay Primary Control Guide d'installation

Honeywell

Honeywell VR4300 Manuel utilisateur

Honeywell

Honeywell Notifier NZM-100-6 Manuel utilisateur

Honeywell

Honeywell Esser 8044 Series Manuel utilisateur

Honeywell

Honeywell VR8204 Series Manuel utilisateur

Honeywell

Honeywell XLS-REL Manuel du produit

Honeywell

Honeywell CGW-MB Manuel utilisateur

Honeywell

Honeywell Krom Schroder PFU 780 Manuel

Honeywell

Honeywell NOTIFIER SCS Series Fiche technique

Honeywell

Honeywell Fire-lite FFT Manuel utilisateur

Honeywell

Honeywell 026593.10 Manuel d'instructions

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur