HOMCOM B31-390V80 Guide d'installation
EN
1-Protection class I: The fitting has an earthing connection: The earth wire (yellow /green ) has to be connected to the clip
marked with .
2-This fitting should only be installed in rooms where direct contact with water is impossible.
3-Consumption in w, according to the speed of the motor.
4-May be operated with a remote control.
WARNINGS
•Read entire booklet carefully before beginning installation and save these instructions.
•To reduce the risk of personal injury, attach the fan directly to the support structure of the building according to these
instructions, and use only the hardware supplied.
•To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to
the outlet box and associated wall switch location.
•All wiring must be in accordance with national and local electrical codes. If you are un-familiar with wiring, you should use
a qualified electrician.
•To reduce the risk of personal injury, do not bend the blade attachment the system when installing, balancing or cleaning
the fan. Never insert foreign objects between rotating fan blades.
•To reduce the risk of fire, electrical shock or motor damage, do not lift or carry the fan by the lead wires.
•Ensure that when mounting the ceiling fan that the fixing can support the moving weight of the fan which is 15.8kg(35lb)
minimum.
•The fan blades cannot be installed lower than 2.3m from the floor.
NOTE:
The important precautions, safeguards and instructions appearing in this manual are not meant to cover all possible
conditions and situations that may occur. It must be understood that common sense, caution and carefulness are factors
which cannot be built into this pro- duct. These factors must be supplied by the person(s) installing, caring for and
operating the unit.
1
IMPORTANT SAFETY PRECAUTIONS
To ensure the success of installation, Be sure to read instructions and check parts for completeness before starting.
NOTE:
To reduce the risk of personal injury, only use the mounting kit provided with this ceiling fan.
TOOLS REQUIRED
Be sure to turn off the power before preparing for installation
2
PREPARING FOR MOUNTING
2. install the mounting bracket to the ceiling. (please ensure the fixing is able to support minimum moving weight of the fan
which is 15.8kg=35Lb)
3
1 .
Remove the mounting bracket (A) from the
Fan-motor assembly (B) by loosening the two canopy
screws (JJ) located in the round holes.
Remove and save the two canopy screws (II) in the
“L” shaped slots. This will enable you to remove the
mounting bracket (A).
power supply from ceiling (120V/60Hz)
4.Remote control connection diagram.
4
Subtitle:
1: AC IN N (White)
2: AC IN L (Black)
3: Live wire for fan L (Black)
4: Live wire for Lamp Control LA (Blue)
5: Common zero line output N (White)
3.
Carefully lift the fan-motor assembly (B) up to the slide-on
mounting bracket (A).
Put the fan-motor assembly (B) assembly onto the mounting
plate’s J hook (MM).
provided by utilizing one of the round holes at the outer rim of
the Fan-motor assembly (B).hang the fan on the J hook (MM).
RECEIVER
MOTOR
5
5.
Carefully unhook the fan from the mounting bracket
(A) and align the locking slots of the fan-motor assembly
(B) with the two screws (II) in the mounting bracket (A).
Push up to engage the slots and turn clockwise to lock in
place. Immediately tighten the two mounting screws
firmly.
Install the other two mounting screws (JJ) (saved
from Assembly Step 1 “Preparing for mounting”) into the
holes in the fan-motor assembly (B) and tighten firmly.
6.
Fasten the blade (C) to the fan-motor assembly
(B) by the blade bracket screws(AA).
Repeat this step for the remaining blade bracket.
7.
Remove the three screws (VV) from the fan - motor
assembly (B).
Align the three holes in the light kit pan (D)Make
sure the notch in the light kit pan (D) Position the light kit
pan (D) and re-install the three screws (VV) that were
removed in the first step to secure the light kit pan (D).
REMOTE CONTROL
IMPORTANTE
1. When the transmitter cannot control the receiver, please check whether the battery switch contact is normal, whether
the positive and negative poles are placed correctly, and whether the battery is sufficient. If the battery voltage is too
low, it will affect the transmitting intensity and cause remote control failure. Please replace the battery in time.
2. When the transmitter cannot control the receiver, please check if there are similar products nearby. The simultaneous
transmission of radio waves by the same kind remote control products will cause interference to each other and affect
the receiving effect.
3. The battery will decrease in power over time. Please replace the battery before it leaks to avoid damage to the
transmitter. Please handle the used battery properly. Keep the battery out of the reach of children.
4. If you do not use it for a long time, please remove the batteries from the transmitter.
6
①Fast speed
②Middle speed
③Low speed
④Fan ON/OF
⑤Light kit ON/OF
Using 1pcs of 12V-23A batteries.
8.
Connect blue wire from fan to black wire from LED
light kit and then connect white wire from fan to white
wire from LED light kit. (SS)
Secure the LED light kit in the light kit pan (D).
Place the glass bowl (E) into the light kit pan (D) ,
aligning the three flat areas on the top flange of the glass
bowl (E) with the three raised dimples in the light kit pan
(D). Turn the glass bowl (E) clockwise until it stops.
Care and Cleaning
Troubleshooting
Problem
Solution
The fan will not
start.
Check the main and branch circuit fuses or breakers.
Check the line wire connections to the fan and switch wire connections in the switch
housing.
The fan is noisy.
Ensure all motor housing screws are snug.
Ensure the screws that attach the blade bracket to the motor hub are tight.
Ensure the wire nut connections are not rattling against each other or the interior wall of
the switch housing.
Allow a 24-hour “breaking in” period. Most noises associated with a new fan disappear
during this time.
If you are using the Ceiling Fan light kit, ensure the screws securing the glassware are
tight. Check that the light bulbs are also secure.
Ensure the canopy is a short distance from the ceiling. It should not touch the ceiling.
Ensure your outlet box is secure and rubber isolator pads were used between the
mounting plate and outlet box.
The fan wobbles.
Check that all blade and blade arm screws are secure.
Most fan wobble problems are caused when blade levels are unequal. Check this level
by selecting a point on the ceiling above the tip of one of the blades. Measure from a point on
the center of the blade to the point on the ceiling. Rotate the fan until the next blade is
positioned for measurement, and measure from the same point on each blade to the ceiling.
Repeat for each blade. Any measurement deviation should be within 1/8 in. Run the fan for
ten minutes. If the minutes. If the fan continues to wobble please contact Customer Service
and a balancing kit will be sent to you at no charge.
7
WARNING: Make sure the power is off
before cleaning your fan.
Because of the fan’s natural movement, some connections may become loose. Check the support connections,
brackets, and blade attachments twice a year. Make sure they are secure. It is not necessary to remove the fan from
the ceiling.
Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning,
as this could damage the motor, or the wood, or possibly cause an electrical shock. Use only a soft brush or Iint-free
cloth to avoid scratching the finish. The plating is sealed with a lacquer to minimize discoloration or tarnishing.
You can apply a light coat of furniture polish to the wood for additional protection and enhanced beauty. Cover
small scratches with a light application of shoe polish.
You do not need to oil your fan. The motor has permanently-lubricated sealed ball bearings.
FR
1-Classe de protection I : Le raccord est doté d'une connexion de mise à la terre : Le fil de terre (jaune /vert) doit être
connecté au clip marqué avec .
2- Installez le produit uniquement dans des pièces sèches et tenez-le à l'écart des substances humides.
3-La consommation de la vitesse du moteur est en Watts.
4-Possibilité de fonctionnement avec une télécommande.
AVERTISSEMENTS
• Lisez attentivement ce manuel avant de procéder à l'installation et conservez-le pour référence ultérieure.
• Pour prévenir tout risque de blessure, fixez le ventilateur directement à la structure de support du bâtiment en suivant
ces instructions. N'utilisez que le matériel fourni.
• Pour prévenir tout risque d'électrocution, avant d'installer votre ventilateur, coupez l'alimentation électrique en fermant
les disjoncteurs de la boîte de sortie et des interrupteurs muraux.
• Tout le câblage doit être conforme aux codes électriques nationaux et locaux. Si vous n'êtes pas familier avec le câblage,
contactez un électricien qualifié.
• Pour prévenir tout risque de blessure, ne pliez pas les pales lors de l'installation ou du nettoyage du ventilateur.
N'insérez jamais d'objets entre les pales du ventilateur en rotation.
• Pour prévenir les risques d'incendie, d'électrocution ou de dommages au moteur, ne soulevez pas et ne portez pas le
ventilateur par les câbles.
• Lors de l'installation du ventilateur, assurez-vous que le plafond peut supporter le poids, qui est d'au moins 15,8 kg (35lbs).
•Les pales du ventilateur ne peuvent pas être installées à moins de 2,3 m du sol.
NOTE :
Les mesures importantes de précaution, de protection et d'instruction figurant dans ce manuel ne sont pas censées
couvrir toutes les conditions et situations possibles qui peuvent se produire. Il faut comprendre que le bon sens, la
prudence et la précaution sont des facteurs qui doivent être aussi pris en considération. Ces facteurs doivent être pris en
compte par la ou les personnes qui installent, entretiennent et utilisent l'appareil.
8
CONSIGNES IMPORTANTES DE SÉCURITÉ
Lisez les instructions et vérifiez que toutes les pièces sont présentes avant de commencer.
NOTE :
Pour prévenir tout risque de blessure, utilisez le kit fourni.
OUTILS REQUIS
Couper l'alimentation électrique avant de procéder à l'installation.
9
Ce manuel convient aux modèles suivants
1
Table des matières
Langues :
Autres manuels HOMCOM Ventilateur
HOMCOM
HOMCOM 824-024V70 Manuel utilisateur
HOMCOM
HOMCOM 824-057V90 Manuel utilisateur
HOMCOM
HOMCOM 824-032V70 Guide d'installation
HOMCOM
HOMCOM B31-394 Guide d'installation
HOMCOM
HOMCOM 824-006V90 Manuel utilisateur
HOMCOM
HOMCOM 824-013V70 Manuel utilisateur
HOMCOM
HOMCOM CTF4202TR-L Manuel utilisateur
HOMCOM
HOMCOM 824-043V70 Guide d'installation
HOMCOM
HOMCOM B31-395V80 Guide d'installation
HOMCOM
HOMCOM 824-018 Manuel utilisateur
HOMCOM
HOMCOM 824-003 Manuel utilisateur
HOMCOM
HOMCOM 824-055V90 Guide d'installation
HOMCOM
HOMCOM 824-024V80 Manuel utilisateur
HOMCOM
HOMCOM 824-014V70 Manuel
HOMCOM
HOMCOM 824-025 Manuel utilisateur
HOMCOM
HOMCOM 824-051V91 Guide d'installation
HOMCOM
HOMCOM 824-007 Manuel utilisateur
HOMCOM
HOMCOM 824-046V80 Guide d'installation
HOMCOM
HOMCOM 824-060V90 Manuel utilisateur
HOMCOM
HOMCOM 824-058V70 Guide d'installation
