Hitachi RAR-M0A5 Manuel utilisateur

– 1 –

Instruction manual Page 1~26

To obtain the best performance, please read this instruction manual completely.

คู่มือการใช้งาน หน ้า 27~54

เพือได ้รับการทํางานทีดีทีสุด โปรดอ่านคู่มืออย่างละเอียด

REMOTE

CONTROLLER

MANUAL









<A>

  

คู่มือการใช้งานหน้า

– 2 –

NAMES AND FUNCTIONS OF REMOTE CONTROL UNIT

REMOTE CONTROLLER

This controls the operation of the indoor unit. Signal range to reach indoor unit is about 7 meters. If

inverter lamp is used, the range of control may be shorter.

This unit can be ﬁxed on a wall using the ﬁxture provided. Before ﬁxing it, make sure the indoor unit

can be controlled from the remote controller.

●Transmission sign

The transmission sign blinks when a signal is sent.

●Display

This indicates the room temperature selected, timer status, function

and intensity of circulation selected.

●AIR SLEEP TIMER button

Use this button to set the air sleep timer mode.

●TEMPERATURE button

Use this button to raise or lower the temperature setting. (Keep pressed,

and the value will change more quickly.)

●START/STOP button

Press this button to start or to stop operation.

●FAN SPEED selector button

This determines the fan speed. Each time you press this button, the

intensity of circulation will change from (AUTO) ➞(HI)

➞(MED) ➞(LOW).

●AUTO SWING button

Controls the angle of the horizontal air deﬂector.

●ONE TOUCH POWERFUL buttonA

Use this button to deliver faster and more comfortable air-conditioning

or start operation.T

●RESET button

●MODE selector button

Use this button to select MODE. Each time you press this button the

MODE selection will change from (COOLING) ➞(SILENT)

➞(DEHUMIDIFY) ➞(FAN).

However, during OFF mode SILENT will be skipped.

●OFF-TIMER button

Select to turn OFF time.

●ON-TIMER button

Select to turn ON time.

Precautions for Use

●Do not put the remote controller in the following places.

●In direct sunlight.

●In the vicinity of a heater.

●Handle the remote controller carefully. Do not drop it on the

ﬂoor, and protect it from water.

●Once the outdoor unit stops, it will not restart for about 3

minutes (unless you turn the power switch off and on or unplug

the power cord and plug it in again).

This is to protect the device and does not indicate a failure.

– 3 –

Use the device for cooling when the outdoor temperature is 21 ~ 43°C.

If indoors humidity is very high (over 80%), some dew may form on the air outlet grille of the indoor unit.

Press the selector button so that the display indicates

(COOL).

Set the desired FAN SPEED with the button (the display

indicates the setting).

(AUTO) : The FAN SPEED is HI at ﬁrst and varies to

MED or LOW automatically when the preset

temperature has been reached.

(HI) : High fan speed.

(MED) : Medium fan speed.

(LOW) : Low fan speed.

Set the desired room temperature with the TEMPERATURE button

(the display indicates the setting).

The range of 25 ~ 28°C is recommended as the

room temperature for cooling.

If the temperature setting is 27°C, the room

temperature will be controlled at around 27°C.

The temperature setting and the actual room temperature may

vary somewhat depending on conditions.

■As the settings are stored in memory of the remote controller, you only

have to press the (START/STOP) button to repeat the same

settings next time.

START

COOLING OPERATION

HI fan speed mode selected

When unit has been operating for a long period of time and the difference between remote controller

setting temperature and actual room temperature is continuously large, the fan speed may increase causing

higher air blow sound.

During the time, cooling capacity will be maximized. If the air blow sound causes any discomfort, please

select “AUTO” or other than “HI” fan speed.

NOTE

Press the button. Cooling operation starts with a beep.

Press the button again to stop the operation.

– 4 –

SILENT OPERATION

During Cooling mode, press the selector button so that

the display indicates (SILENT) along with the (COOL)

symbol. Silent operation starts with a beep.

CANCELLATION of SILENT Operation

Cancel Condition Operation mode after cancel

Key press

Stop operation

Selected mode operation

(COOLING) (SILENT)

(FAN) (DEHUMIDIFY)

COOLING operation in previous setting

POWERFUL operation

NOTE:

Under SILENT mode operation and quiet environment, phenomena like ﬂowing noise of refrigerant in the

refrigerating cycle may occur, but this is normal for the operation.

– 5 –

DEHUMIDIFYING OPERATION

Use the device for dehumidifying when the room temperature is over 16°C.

When it is under 15°C, the dehumidifying function will not work.

■Dehumidifying Function

When the room temperature is higher than the temperature setting: The device will dehumidify the room

and reducing the room temperature to the preset level.

When the room temperature is lower than the temperature setting: Dehumidifying will be performed at the

temperature setting slightly lower than the current room temperature, regardless of the temperature setting.

The function will stop (the indoor unit will stop emitting air) as soon as the room temperature becomes lower

than the setting temperature. You might feel a bit colder in dehumidifying operation.

■As the settings are stored in memory in the remote controller, you

only have to select (DEHUMIDIFY) then press the

button next time.

Set the desired room temperature with the TEMPERATURE

button (the display indicates the setting).

The range of 20 ~ 26˚C is recommended as

the room temperature for dehumidifying.

Press the selector button so that the display indicates

(DEHUMIDIFY).

The FAN SPEED is set at LOW automatically.

The FAN SPEED button does not work during DEHUMIDIFY

operation.

Press the button. Dehumidifying operation starts with

a beep. Press the button again to stop the operation.

START

– 6 –

FAN OPERATION

Press the selector button so that the display indicates

(FAN).

■As the settings are stored in memory in the remote controller, you

only have to select (FAN) then press the

button next time.

Press the button. Fan operation starts with a beep.

Press the button again to stop the operation.

START

Set the desired FAN SPEED with the button.

(the display indicates the selectable setting).

(HI) : High fan speed.

(MED) : Medium fan speed.

(LOW) : Low fan speed.

In Fan operation mode the device is function as an air circulator.

■FAN Function

During FAN operation, compressor does not run and there is no cooling operation with only indoor fan running.

– 7 –

ONE-TOUCH POWERFUL MODE

Press the button.

●Operation start with a signal received sound “beep”.

●Unit will be forced operate in (COOL) with POWERFUL

MODE fan speed for 20 minutes, within this 20 minutes, fan speed

may varies. Indicator appear during this period. (Operation

lamp at indoor unit is blinking).

●After 20 minutes, operation lamp stop blinking and indicator

will disappear while unit will be in previous mode setting.

●Air blow sound will be slightly high due to forced operation.

CANCELLATION of POWERFUL Operation

If feeling so cold,

cancel this powerful

mode as mentioned in

“CANCELLATION of

POWERFUL operation”.

Cancel Condition Operation mode after cancel

Key press

Press or

20 minutes time is up

Press or

Stop operation

Selected mode operation

(COOLING) (SILENT)

(FAN) (DEHUMIDIFY)

AIR SLEEP TIMER operation

COOLING operation in previous setting

– 8 –

HOW TO SET THE AIR SLEEP TIMER

Press the button, and the display changes as shown below.

Mode

Air Sleep Timer

Indication

Air Sleep Timer: The device will continue working for the

designated number of hours and then turn off.

Point the signal window of the remote controller toward the indoor

unit, and press the AIR SLEEP TIMER button.

The timer information will be displayed on the remote controller.

The TIMER lamp lights with a beep from the indoor unit.

Cooling

“ ” ,

Silent

“ ”

and

Dehumidifying

“ ”

Explanation of the air sleep timer

The device will control the FAN SPEED and room temperature automatically so as to be quiet

and good for people’s health.

You can set the sleep timer to turn off after 1,2,3 --

➞

9 or 10 hours. The FAN SPEED and

room temperature will be controlled as shown below.

Function Operation

The room temperature will be

controlled 2°C above the setting

temperature and the FAN SPEED

will be set to LOWEST 1 hour

after the setting of the air sleep

timer.

Air Sleep

Timer

Operation with the air sleep timer

– 9 –

HOW TO SET THE TIMER

■ON Timer and OFF Timer are available.

OFF TIME setting

●Select the OFF TIME by pressing the (OFF TIMER)

Button.

●Setting time will change according to the below sequence

when you press the button.

OFF Timer Reservation ■Operation stop at setting time

ON TIME setting

●Select the ON TIMER by pressing the (ON

TIMER) Button.

●Setting time will change according to the below

sequence.

ON Timer Reservation ■Operation will start for setting

temperature at setting time.

●After the OFF TIMER is set, the hour display will be counting

down as time passes.

●After the ON TIMER is set, the hour display will be counting

down as time passes.

– 10 –

AIR FLOW LOUVERS ADJUSTMENTS

2Adjustment of the conditioned air to the left and right.

Hold the second vertical air deﬂector of each set of vertical

air deﬂectors from right as shown in the ﬁgure and adjust the

conditioned air to the left or right.

●If the “ (AUTO SWING)” button is pressed

once, the horizontal air deﬂector swings up and down.

If the button is pressed again, the deﬂector stops in its

current position. Several seconds (about 6 seconds) may

be required before the deﬂector starts to move.

●Use the horizontal air deﬂector within the adjusting range

shown on the right.

●When the operation is stopped, the horizontal air deﬂector

moves and stops at the position where the air outlet

closes.

!CAUTION

●In “Cooling” operation, do not keep the horizontal air

deﬂector swinging for a long time. Some dew may form

on the horizontal air deﬂector and dew may drop.

Adjustment of the conditioned air in the upward and downward

directions.

The horizontal air deﬂector is automatically set to the proper

angle suitable for each operation. The deﬂector can be swung

up and down continuously and also set to the desired angle

using the “ (AUTO SWING)” button.

Do not insert a ﬁnger, a rod or other objects into the air outlet or inlet as the fan is rotating at a high speed,

it will cause injury. Before any cleaning or adjusting the deﬂectors, be sure to switch OFF the operation.

WARNING

Table des matières

Langues :

Autres manuels Hitachi Télécommande

Hitachi

Hitachi RAR-6N2 Manuel utilisateur

Hitachi

Hitachi PC-ARFLE Manuel utilisateur

Hitachi

Hitachi PC-ARH1E Manuel utilisateur

Hitachi

Hitachi RC-AGU1EA0G Manuel utilisateur

Hitachi

Hitachi RC-AGU1EA0G Manuel utilisateur

Hitachi

Hitachi SPX-RCDA Manuel utilisateur

Hitachi

Hitachi SPX-WKT2 Manuel utilisateur

Hitachi

Hitachi RC-AGU1EA0A Manuel utilisateur

Hitachi

Hitachi RAR-6N1 Manuel utilisateur

Hitachi

Hitachi PC-ARFG2-Z Mode d’emploi

Hitachi

Hitachi REMOTE OPERATOR WOP Manuel utilisateur

Hitachi

Hitachi PC-LH3A Manuel utilisateur

Hitachi

Hitachi SPX-RCK2 Manuel utilisateur

Hitachi

Hitachi PC-P5H Manuel utilisateur

Hitachi

Hitachi SPX-RCDB Manuel utilisateur

Hitachi

Hitachi SPX-RCK3 Manuel utilisateur

Hitachi

Hitachi PC-ARFG-E Manuel utilisateur

Hitachi

Hitachi PC-ARH Manuel utilisateur

Hitachi

Hitachi air Home RC-AGU1EA0S Manuel utilisateur

Hitachi

Hitachi PC-LH3A Manuel utilisateur

Hitachi

Hitachi RAR-5E2 Manuel utilisateur

Hitachi

Hitachi RC-AGU1EA0G Manuel utilisateur

Hitachi

Hitachi PC-ARFH1E-02 Manuel utilisateur

Hitachi

Hitachi CIW03-H Mode d’emploi

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation