Hirschmann GRS103 Series Manuel utilisateur

Installation GRS103

Release

03/2022

Technical support

https://hirschmann-support.belden.com

User Manual

Installation

Industrial ETHERNET Workgroup Switch

GRS103 Family

25.03.2022 Installation GRS103

Release

03/2022

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at:

https://www.doc.hirschmann.com

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Installation GRS103

Release

03/2022 3

Contents

1 About this manual 7

2 General safety instructions 8

2.1 Warning symbols 8

2.2 Intended use 9

2.3 National and international safety regulations 10

2.4 Installation site requirements 10

2.5 Qualification requirements for personnel 10

2.5.1 Media modules 10

2.6 Device casing 11

2.6.1 ESD Guidelines 11

2.7 Strain relief 12

2.8 Shielded ground 12

2.9 Electrical connections 12

2.9.1 Grounding the device 12

2.9.2 Requirements for connecting electrical wires 12

2.9.3 Requirements for connecting the supply voltage 13

2.9.4 Requirements for connecting the signal contact 14

2.10 Connecting data cables 14

2.11 LED or laser components 15

2.12 Recycling note 15

3 Approvals 16

3.1 CE marking 16

3.2 UKCA marking 17

3.3 FCC note 18

3.4 Relevant for installations in 19" switch cabinets according to

UL 60950-1/UL 62368-1 18

4Key 20

5 Description 21

5.1 General device description 21

4Installation GRS103

Release

03/2022

5.1.1 GRS103 basic devices 22

5.1.2 Modular GRS103 basic devices 23

5.1.3 GRS103 media modules 24

5.2 Device views 28

5.2.1 Basic device 28

5.2.2 Modular basic device 28

5.2.3 Rear view 29

5.2.4 Port assignment 29

5.3 Power supply 30

5.3.1 Basic device 30

5.3.2 PoE supply voltage for M1-8TP-RJ45 PoE media

module 31

5.4 Management interfaces 32

5.4.1 Signal contact 32

5.4.2 USB-C interface: ACA22-USB-C 33

5.5 Ethernet ports 34

5.5.1 10/100 Mbit/s twisted pair port 34

5.5.2 10/100 Mbit/s PoE port 34

5.5.3 10/100/1000 Mbit/s twisted pair port 35

5.5.4 10/100/1000 Mbit/s twisted pair port 36

5.5.5 100 Mbit/s F/O port 36

5.5.6 100/1000 Mbit/s Combo port 37

5.6 Display elements 37

5.6.1 Device status 37

5.6.2 Port status 39

6 Installation 40

6.1 Checking the package contents 40

6.2 Installing an SFP transceiver (optional) 41

6.3 Mounting a cover panel 41

6.4 Mounting a media module 41

6.5 Installing the device 42

6.5.1 Selecting the installation location 43

6.5.2 Mounting on a flat surface 44

6.5.3 Mounting on a vertical flat surface 45

6.5.4 Mounting in a switch cabinet 46

6.6 Grounding the device 49

Installation GRS103

Release

03/2022 5

6.7 Connecting the signal contact (optional) 49

6.8 Connecting the supply voltage 50

6.9 Connecting the PoE supply voltage to the M1-8TP-

RJ45 PoE media module (optional) 50

6.10 Connecting data cables 52

6.11 Support of PoE 52

6.12 Filling out the inscription label 53

7 Operating the device 54

8 Making basic settings 55

8.1 Default settings 55

8.2 First login (Password change) 56

9 Monitoring the ambient conditions 57

9.1 Monitoring the ambient air temperature 57

10 Maintenance and service 58

11 Disassembly 59

11.1 Removing an SFP transceiver (optional) 59

11.2 Removing a media module 59

11.3 Removing the device 60

12 Technical data 62

12.1 General technical data 62

12.1.1 Basic device 62

12.1.2 Media modules 63

12.2 Supply voltage 63

12.2.1 Basic device 63

12.2.2 Media modules 63

12.3 Power consumption/power output 64

12.4 Signal contact 65

12.5 Climatic conditions during operation 65

12.5.1 Basic device 65

12.5.2 Media modules 65

6Installation GRS103

Release

03/2022

12.6 Climatic conditions during storage 66

12.7 Dimension drawings 66

13 EMC 67

14 Immunity 68

15 Network range 69

15.1 10/100/1000 Mbit/s twisted pair port 69

15.2 Fast Ethernet SFP transceiver 69

15.3 Bidirectional Fast Ethernet SFP transceiver 71

15.4 Gigabit Ethernet SFP transceiver 72

15.5 Bidirectional Gigabit Ethernet SFP transceiver 73

16 Scope of delivery 75

16.1 Basic device 75

16.2 Media modules 75

17 Order numbers 76

18 Accessories 77

19 Underlying technical standards 79

A Further support 80

Installation GRS103

Release

03/2022 7

1 About this manual

The “Installation” user manual contains a device description, safety

instructions, a description of the display, and the other information that you

need to install the device.

Documentation mentioned in the “User Manual Installation” that is not

supplied with your device as a printout can be found as PDF files for

downloading on the Internet at: https://www.doc.hirschmann.com

8Installation GRS103

Release

03/2022

2 General safety instructions

Note: Read these instructions carefully, and familiarize yourself with the

device before trying to install, operate, or maintain it. The following notes may

appear throughout this documentation or on the device. These notes warn of

potential hazards or call attention to information that clarifies or simplifies a

procedure.

You operate this device with electricity. Improper usage of the device entails

the risk of physical injury or significant property damage. The proper and safe

operation of this device depends on proper handling during transportation,

proper storage and installation, and careful operation and maintenance

procedures.

Before connecting any cable, read this document, and the safety

instructions and warnings.

Operate the device with undamaged components exclusively.

The device is free of any service components. In case of a damaged or

malfunctioning device, turn off the supply voltage and return the device to

Hirschmann for inspection.

2.1 Warning symbols

This is a general warning symbol. This symbol alerts you to

potential personal injury hazards. Observe all safety notes that

follow this symbol to avoid possible injury or death.

WARNING

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all

the data transmission devices individually.

Before you start any machine which is controlled via data transmission, be

sure to complete the configuration of all data transmission devices.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

Installation GRS103

Release

03/2022 9

If this symbol is displayed in addition to a safety instruction of the

type “Danger” or “Warning”, it means that there is a danger of

electric shock and failure to observe the instructions will inevitably

result in injury.

This symbol indicates the danger of hot surfaces on the device. In

connection with safety instructions, non-observance of the

instructions will inevitably result in injuries.

2.2 Intended use

Use the product only for the application cases described in the

Hirschmann product information, including this manual.

Operate the product only according to the technical specifications.

See “General technical data” on page 62.

Connect to the product only components suitable for the requirements of

the specific application case.

DANGER

DANGER draws attention to an immediately dangerous situation, which will

inevitably result in a serious or fatal accident if not observed.

WARNING

WARNING indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION

CAUTION indicates a possible danger which, if not avoided, may result in

minor injuries.

NOTICE

NOTE provides information about procedures that do not involve the risk of

injury.

10 Installation GRS103

Release

03/2022

2.3 National and international safety

regulations

Verify that the electrical installation meets local or nationally applicable

safety regulations.

2.4 Installation site requirements

Operate the device only at the specified ambient temperature (temperature

of the ambient air at a distance of 5 cm (2 in) from the device) and at the

specified relative humidity.

When you are selecting the installation location, make sure you observe

the climatic threshold values specified in the technical data.

Use the device in an environment with a maximum pollution degree that

complies with the specifications in the technical data.

See “General technical data” on page 62.

If the device is not installed in a horizontal position, it must be installed in

a control cabinet or other enclosure with fire protection properties. The

enclosure can be made of metal or plastic with fire protection properties

of at least V-1 according to IEC 60695-11-10. Bottom openings must NOT

exceed 2 mm (0.078 in) in diameter.

2.5 Qualification requirements for personnel

Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the

prerequisite for grounding and labeling circuits, devices, and systems in

accordance with current standards in safety technology.

Qualified personnel are aware of the dangers that exist in their work.

Qualified personnel are familiar with appropriate measures against these

hazards in order to reduce the risk for themselves and others.

Qualified personnel receive training on a regular basis.

2.5.1 Media modules

Only qualified personnel are authorized to install or remove media modules.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Hirschmann Changer

Hirschmann

Hirschmann RH1-TP Manuel

Hirschmann

Hirschmann OCTOPUS OS20 Manuel utilisateur

Hirschmann

Hirschmann PowerMICE Manuel utilisateur

Hirschmann

Hirschmann GECKO Manuel utilisateur

Hirschmann

Hirschmann OCTOPUS 8M-8PoE Manuel utilisateur

Hirschmann

Hirschmann MACH102 Series Manuel utilisateur

Hirschmann

Hirschmann MSM20 Manuel utilisateur

Hirschmann

Hirschmann MAR1042 Manuel utilisateur

Hirschmann

Hirschmann MACH104-20TX-F Series Manuel utilisateur

Hirschmann

Hirschmann OCTOPUS 8M Series Manuel utilisateur

Hirschmann

Hirschmann RS20 series Manuel utilisateur

Hirschmann

Hirschmann SPIDER 5TX Manuel

Hirschmann

Hirschmann RH1-TP/FL Manuel

Hirschmann

Hirschmann RS20 series Manuel utilisateur

Hirschmann

Hirschmann Power MICE Manuel utilisateur

Hirschmann

Hirschmann MSM20 Manuel utilisateur

Hirschmann

Hirschmann RS20 series Manuel utilisateur

Hirschmann

Hirschmann RS20 series Manuel utilisateur

Hirschmann

Hirschmann SPIDER PL Manuel utilisateur

Hirschmann

Hirschmann CS30 Manuel utilisateur

Hirschmann

Hirschmann Dragon PTN Manuel utilisateur

Hirschmann

Hirschmann MACH1040 Manuel utilisateur

Hirschmann

Hirschmann BXS Manuel utilisateur

Hirschmann

Hirschmann RSPE 30 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur