HIK VISION DS-19A08-BNG Manuel utilisateur

Title:

How to Confirm Fault Type When

Control Panel in Zone Fault Status

Version:

v1.0

Date:

7/11/2017

Product:

Alarm Device

Page:

1 of 3

Description

When control panel is in disarm status, it shows “Zone Fault” for some zones. In

this case, control panel can not arm system successfully.

Problem Checking Flow

Zone Fault

Detector is in

alarm

Remove Detector,

Replaced with an

EOL directly

Connect to zone

terminal

Fault

Disappears?

Measure Voltage

between zone’s

terminal Z and G

故障是否消失

Keep Detector in

Normal Statues,

Fault

Disappears?

NO Problem in

Detector and

Control Panel

探测器故障

Detector Fault or

Wiring Fault

总线接线问题

Voltage in

Normal Range Detector Fault or

Wiring Fault

Control Panel Fault

Yes

Title:

How to Confirm Fault Type When

Control Panel in Zone Fault Status

Version:

v1.0

Date:

7/11/2017

Product:

Alarm Device

Page:

2 of 3

Detail Steps

Step 1: Check whether the Detector is in Alarm Status

If detector is in alarm status, eliminate all the factors that will cause alarm for detector.

If detecor still can not go back to normal status, we can confirm it is detector fault; If

detector is in normal status, but control panel is still in “zone fault”, go on next

checking step.

Step 2: Connect Corresponding End of Line Resistor to Terminal Z and G for the

Fault Zone

If “Zone Fault” disappears, we can confirm it is a wiring fault between detector and

control panel. Check wire poor contact, short circuit, open circuit between detector and

control, or signal cable is too close to power cable. After all these wiring issue have

checked, but control panel is still in “zone fault” status, go on next step.

Step 3: Measure Voltage between Z and G for the Fault Zone

According to the chart below, if voltage between Z and G is out of normal range, we

can confirm it is a control panel fault. Please ask technical support team for further

help.

Control Panel Input

Voltage(V)

EOL Resistor(Ω)

Voltage between Z and G

Min

Max

14.3

2.2K

5.6

9.68

3.3K

7.24

11.32

5.6K

8.58

12.66

8.2K

9.34

12.55

10.5

2.2K

4.04

6.98

3.3K

5.21

8.15

5.6K

6.18

9.12

8.2K

6.73

9.05

Note：This voltage range is measured without tamper-proof EOL resistor

Title:

How to Confirm Fault Type When

Control Panel in Zone Fault Status

Version:

v1.0

Date:

7/11/2017

Product:

Alarm Device

Page:

3 of 3

First Choice for Security Professionals

HIKVISION Technical Support

Autres manuels HIK VISION Système de sécurité

HIK VISION

HIK VISION DS-K3B802BX Series Manuel utilisateur

HIK VISION

HIK VISION DS-PEA12-P/ZJ Manuel utilisateur

HIK VISION

HIK VISION DS-PEA22-F Manuel utilisateur

HIK VISION

HIK VISION Pyronix EURO 46 V10 Manuel du propriétaire

HIK VISION

HIK VISION DS-PEA1-21 Manuel utilisateur

HIK VISION

HIK VISION DS-PS1-I-WB Manuel utilisateur

HIK VISION

HIK VISION AX HYBRID PRO Manuel utilisateur

HIK VISION

HIK VISION Pyronix Enforcer V10 Manuel de service

HIK VISION

HIK VISION DS-PWA32-HR Manuel utilisateur

HIK VISION

HIK VISION AX PRO Series Guide d'installation

HIK VISION

HIK VISION DS-TCG405-E Manuel utilisateur

HIK VISION

HIK VISION EKI-K41B44W Manuel utilisateur

HIK VISION

HIK VISION DS-PHA20-P Manuel utilisateur

HIK VISION

HIK VISION DS-PRI120 Manuel utilisateur

HIK VISION

HIK VISION DS-MI9605-GA Series Manuel utilisateur

HIK VISION

HIK VISION AX PRO Manuel utilisateur

HIK VISION

HIK VISION DS-2TD6537T-50H4LX/W Manuel utilisateur

HIK VISION

HIK VISION DS-PEA Series Manuel utilisateur

HIK VISION

HIK VISION AX PRO Manuel utilisateur

HIK VISION

HIK VISION DS-9600NI-ST Series Manuel utilisateur

HIK VISION

HIK VISION DS-1901I Guide de l'administrateur

HIK VISION

HIK VISION DS-PEA101 Series Manuel utilisateur

HIK VISION

HIK VISION AX PRO M2 Manuel utilisateur

HIK VISION

HIK VISION MV-PD030001-01 Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur