HighPoint RocketRAID 37 Series Manuel utilisateur

RocketRAID 37xx/8xx/28xx Uniontech OS Server 20 Installation Guide

RocketRAID 37xx/8xx/28xx SATA

Controller

Uniontech OS Server 20（1050d）

Installation Guide

Version 1.0.0

Last updated on May 27, 2022

RocketRAID 37xx/8xx/28xx Uniontech OS Server 20 Installation Guide 
i 
Table of Contents 
1 Overview.........................................................................................................................................1 
2 Installing Uniontech OS Server 20 on RR3740Acontroller......................................................1 
Step 1 Prepare Your Hardware for Installation...........................................................................1 
Step 2 Check System EFI Settings.............................................................................................1 
Step 3 Flash UEFI Rom to RR3740A ........................................................................................1 
Step 4 CreateArray.....................................................................................................................2 
Step 5 Prepare the Driver Diskette .............................................................................................3 
Step 6 Install Uniontech OS Server 20.......................................................................................3 
3 Installing RR3740Adriver on an Existing System.....................................................................6 
Step 1 Obtain and install the Driver Module..............................................................................7 
Step 2 Configure System to Mount Volumes when Startup.......................................................7 
4 Monitoring the Driver...................................................................................................................7 
5 Installing RAID Management Software......................................................................................7 
6 Rebuilding Driver Module for System Update...........................................................................7 
 
 

RocketRAID 37xx/8xx/28xx Uniontech OS Server 20 Installation Guide

- 1 -

1 Overview

The purpose of this document is to provide clear instructions on how to install and use

RR3740A Controller on Uniontech OS Server 20 system.

2 Installing Uniontech OS Server 20 on RR3740A

controller

If you would like to install Uniontech OS Server 20onto drives attached to RR3740A

controller, please perform the following operations:

Step 1 Prepare Your Hardware for Installation

Notcie: If your FT2000 motherboard is not directly connected to the SSD disk, it is normal for the

buzzer to sound continuously. You can communicate with the motherboard supplier to mute it.

After you attach your hard disks to RR3740Acontroller, you can use RR3740A EFI

Utility Utility to configure your hard disks as RAID arrays, or just use them as single

disks.

Before installation, you must remove all the disk drives, which are not physically attached

to RR3740Acontroller, from your system.

Note

If you have other SCSI adapters installed, you must make sure the RR3740A controller

EFI will be loaded firstly. If not, try to move it to another PCI slot. Otherwise you may be

unable to boot up your system.

Step 2 Check System EFI Settings

In your system BIOS SETUP menu, change Boot Sequence in such a way that the system

will first boot from EFI CDROM, and then from SCSI. Refer to your SCSI manual to see

how to set boot sequence.

If your EFI settings do not support such a boot sequence, you can first set it to boot from

EFI CDROM.After you finish installation, set SCSI as the first boot device to boot up the

system.

Step 3 Flash UEFI Rom to RR3740A

a. Unzip RR3740A UEFI package to root dir (/) of a USB flash driver, and insert the

USB flash drive to the motherboard;

b. Booting from the UEFI USB flash and enter the UEFI environment;

c. Command with “rr3740.nsh”, flash UEFI rom to RR3740A Controller and reboot;

RocketRAID 37xx/8xx/28xx Uniontech OS Server 20 Installation Guide

- 2 -

Step 4 Create Array

a. Attach two SATA to RR3740A Controller;

Note

Make sure your USB flash partition format is FAT32.

b. Boot, in the presence of the motherboard Log screen, there will be SATA

information：

c. Enter the motherboard’s Boot List and select start from UEFI USB flash:

d. Command ”Arraycreate.efi” to enter the Utility:

RocketRAID 37xx/8xx/28xx Uniontech OS Server 20 Installation Guide

- 3 -

e. Command “create RAID1 ”.

Create RAID1 array with all disks and with maximum capacity.

f. Command “exit”,exit the UEFI environment；

g. For more command usages, refer to Appendix A.

Step 5 Prepare the Driver Diskette

Extract RR3740A_UOS20_Server_1050d_aarch64_vx.x.x_xx_xx_xx.tar.gz

to top(/) directory of an USB flash drive. It will look like:

Step 6 Install Uniontech OS Server 20

Insert the USB diskette in to the USB port.

1) Start installing Uniontech OS Server 20 by booting from the installation CD/DVD.

2) On the startup screen. Just select “Install UnionTech OS Server 20(Graphic)”, and

then press ENTER to start installation.

RocketRAID 37xx/8xx/28xx Uniontech OS Server 20 Installation Guide

- 4 -

3) When the installation switches to the graphical installation, press “Ctrl+ALT+F2”to

switch the shell on console 2 before select "Next".

Type the following commands to load the RR3740Adriver:

# sudo su //get root

# mkdir /hptdd

# mount /dev/sdb1 /hptdd

# cp –r /hptdd/hptdd /tmp/

# umount /dev/sdb1

RocketRAID 37xx/8xx/28xx Uniontech OS Server 20 Installation Guide

- 5 -

Unplug all USB storage devices from system before execute following command:

# sh /tmp/hptdd/preinst.sh

4) Then type the following commands to restart the system installer:

# systemctl restart lightdm

The system installer will restart and select “Next”to continue installation.

5) When the installation program comes to selecting the installation location, full

installation is recommended.

6) When the screen shows that “Restart”，

RocketRAID 37xx/8xx/28xx Uniontech OS Server 20 Installation Guide

- 6 -

press “CRL+ALT+F2”to switch console 2 and type the following commands:

sh /tmp/hptdd/postinst.sh /dev/sdb

Press “Ctrl+ALT+F7”to switch back to installation screen and finish the

installation.

3 Installing RR3740A driver on an Existing System

Note

If you use a SCSI adapter to boot your system, you must make sure the RR3740A

controller EFI will be loaded after that adapter’s EFI. If not, try to move it to another PCI

slot. Otherwise you may be unable to boot up your system.

RocketRAID 37xx/8xx/28xx Uniontech OS Server 20 Installation Guide

- 7 -

Step 1 Obtain and install the Driver Module

Extract the driver archive to a temporary directory and execute the install.sh to install the

driver to the system. For example:

# mkdir /tmp/dd

# tar xzvf RR3740A_UOS20_Server_1050d_aarch64_vx.x.x_xx_xx_xx.tar.gz

-C /tmp/dd

# cd /tmp/dd

# sh install.sh

If the driver of previous version has been in the initrd image, the installer will update the

initrd image or it will make the driver automatically loaded while system up.

Step 2 Configure System to Mount Volumes when Startup

Now you can inform the system to automatically mount the array by modifying the file

/etc/fstab. E.g. you can add the following line to tell the system to mount /dev/sda1 to

location /mnt/raid after startup:

/dev/sda1 /mnt/raid ext3defaults 0 0

4 Monitoring the Driver

Once the driver is running, you can monitor it through the Linux proc file system support.

There is a special file under /proc/scsi/rr3740a/. Through this file you can view driver

status and send control commands to the driver.

Note

The file name is the SCSI host number allocated by OS. If you have no other SCSI cards

installed, it will be 0. In the following sections, we will use x to represent this number.

Using the following command to show driver status:

# cat /proc/scsi/rr3740a/x

This command will show the driver version number, physical device list and logical device

list.

5 Installing RAID Management Software

HighPoint RAID Management Software is used to configure and keep track of your hard

disks and RAID arrays attached to RR3740A controller. Installation of the management

software is optional but recommended.

Please refer to HighPoint RAID Management Software documents for more information.

6 Rebuilding Driver Module for System Update

When the system updates the kernel packages, the driver module rr3740a.ko should be

built and installed manually before reboot.

RocketRAID 37xx/8xx/28xx Uniontech OS Server 20 Installation Guide

- 8 -

To build the driver module, the RR3740A open source package and the following building

packages are needed: gcc, kernel-devel. The open source package can be got from

HighPoint website: http://www.highpoint-tech.com while the building tools can be

installed from UOS website: https://www.chinauos.com

Note: the package version of kernel-devel should be the same to the updated kernel

package.

Refer to the REAME file distributed with HighPoint RR3740A open source package on

how to build and install the driver module.

Autres manuels pour RocketRAID 37 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels HighPoint Contrôleurs

HighPoint

HighPoint Rocket 700 Series Manuel utilisateur

HighPoint

HighPoint R1000 Series Manuel utilisateur

HighPoint

HighPoint SSD7000 Series Manuel utilisateur

HighPoint

HighPoint SSD7749M Manuel utilisateur

HighPoint

HighPoint RR64 L Series Manuel utilisateur

HighPoint

HighPoint RocketRAID 2722A Manuel utilisateur

HighPoint

HighPoint SSD7110 Feuille d'instructions

HighPoint

HighPoint SSD7580A Manuel utilisateur

HighPoint

HighPoint RocketRAID 2840A Manuel utilisateur

HighPoint

HighPoint SSD7103 Manuel utilisateur

HighPoint

HighPoint RocketRAID 37 Series Manuel utilisateur

HighPoint

HighPoint RocketRAID mini SAS 3G HBA Series Manuel utilisateur

HighPoint

HighPoint SSD7505 Manuel utilisateur

HighPoint

HighPoint SSD7120 Manuel utilisateur

HighPoint

HighPoint Rocket Dual eSATA 6Gb/s For Mac Manuel utilisateur

HighPoint

HighPoint Rocket 700 Series Manuel utilisateur

HighPoint

HighPoint HPT366 Guide d'installation et d'utilisation

HighPoint

HighPoint ATA-133 RAID Manuel utilisateur

HighPoint

HighPoint SSD7749E Manuel utilisateur

HighPoint

HighPoint SSD7180 Manuel utilisateur

HighPoint

HighPoint RocketRAID 2711 Manuel utilisateur

HighPoint

HighPoint RocketU 1142A Manuel utilisateur

HighPoint

HighPoint SSD7101A-1 Manuel utilisateur

HighPoint

HighPoint RR640L Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur