HighPoint R1508 Manuel utilisateur

1

R1508

8x M.2 Port to PCIe 4.0x16 NVMe HBA

Quick Installation Guide

V1.00

2

System Requirements

PC Requirements

•System with a free PCIe 4.0 x16 slot

•Windows 11 and 10, Windows Server 2019 and 2022

•Linux kernel 3.10 and later

•macOS 10.13 and later

•FreeBSD 12.1 and later

R1508 Kit Content

•R1508 Controller Card

•Quick Installation Guide

3

R1508 Hardware

Front View

Full-Length anodized aluminum heat sink

PCIe 4.0 x16 Host Interface

Full Height form factor

0000

Low-Noise Cooling Fan

External power port

4

R1508 Hardware Installation:

Step 1. On the rear of the R1508, remove the six screws that secure the

unit’s heat sink to the PCB.

Step 2. Carefully remove the fan’s power cable from the right-side of

the heatsink as shown below, then carefully flip the heatsink to the

left (like turning a page from a book).

Note: Take care when moving the heatsink to prevent damaging

the left fan’s power cable.

5

Step 3. After removing the casing, carefully turn it over to view the

thermal pad. The blue films must be removed from the pad before

reinstalling the panel. These films protect the pad from damage and

foreign objects prior to installation, however, they will also prevent the

thermal pad from conducting the heat away from the NVMe SSD's if we

don't remove it.

Step 4. These 8 screws are used to install the NVMe SSD’s.

6

Step 5. Please remove these screws from each of the M.2 slots.

Step 6. Gently insert the SSD into the slot.

Note: Please make sure all disks are clean before you insert them

into the slot to avoid unexpected situations.

Step 7. Refasten the screw to secure the SSD.

7

Repeat Steps 4 to 6 to install the remaining SSDs.

The following example shows eight Gen4 SSDs installed into Ports 1-8:

Step 8. After installing all SSDs, carefully flip the heatsink to the right.

Note: Make sure each SSD is carefully aligned and fastened to the

SSD7540 using the supplied screws. Loosely attached SSDs may

not be detected by the R1508 or host system.

Step 9. Carefully reinsert in the power supply cable of the cooling fan

that was removed in step 2.

8

Step 10. On the rear of the R1508, refasten the 6 screws that were

removed in step 1.

Note

：

Make sure the aluminum cover is properly aligned with the

controller board (PCB), and that it makes full contact with the

thermal pad, before refastening it to the R1508. If the cover is

improperly installed, the fan and thermal pad will be unable to

sufficiently cool the NVMe SSD’s and controller componentry,

which may result in damage to the SSD’s or controller hardware,

performance loss, unstable I/O, and the loss of data.

9

Step 11. Power up the SSD external power supply

Note: If the external power supply is not powered on, the SSDs

may drop offline or remain undetected, which could lead to data

loss.

R1508 relies on two power sources to support eight SSDs; power

supplied through the PCIe bus, and power from the system’s PSU

via an external 6 pin PCIe power cable. If the external cable is not

connected, there will be insufficient power to support all 8 SSD’s;

this may cause the SSDs to drop offline.

Note

：

The R1508 does not require the external power cord when

used with Mac Pro 2019

.

10

Note: Please be sure to connect NVMe before using the product to

reduce the occurrence of unnecessary errors!

Connect 6 pin PCIe power cable

Table des matières

Autres manuels HighPoint Matériel informatique

HighPoint

HighPoint SSD7120 Manuel utilisateur

HighPoint

HighPoint rSSD 7101B Manuel utilisateur

HighPoint

HighPoint HS8004F Manuel utilisateur

HighPoint

HighPoint 644L Manuel utilisateur

HighPoint

HighPoint rDrive 6114VW-4T Manuel utilisateur

HighPoint

HighPoint SSD7202 Manuel utilisateur

HighPoint

HighPoint RocketAIC 7505HW Series Manuel utilisateur

HighPoint

HighPoint SSD7103 Manuel utilisateur

HighPoint

HighPoint RocketRAID 3700 Series Manuel utilisateur

HighPoint

HighPoint Rocket 1580 Manuel utilisateur

HighPoint

HighPoint BRD Series Manuel utilisateur

HighPoint

HighPoint R1000 Series Manuel utilisateur

HighPoint

HighPoint U.2 Series Manuel utilisateur

HighPoint

HighPoint SSD7103 Manuel utilisateur

HighPoint

HighPoint Rocket 1108A Manuel utilisateur

HighPoint

HighPoint HighPoint RocketRAID 2700 Series Manuel utilisateur

HighPoint

HighPoint SSD7540L Manuel utilisateur

HighPoint

HighPoint SSD7505 Manuel utilisateur

HighPoint

HighPoint RocketCache 3240X8 Manuel utilisateur

HighPoint

HighPoint SSD7103 Manuel utilisateur

HighPoint

HighPoint rDrive 6628TW Manuel utilisateur

HighPoint

HighPoint SRD Series Manuel utilisateur

HighPoint

HighPoint SSD7110 Manuel utilisateur

HighPoint

HighPoint SSD7140A Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur