Heath Zenith SL-7464-03 Manuel utilisateur

This chime requires 3 “C” alkaline batteries (not included). In typical use,

alkaline batteries will last up to 2 1/2years.

Wireless Chime

Figure 1

WARNING: To prevent possible

SERIOUS INJURY or DEATH:

• NEVER allow small children near

batteries.

• If battery is swallowed, immediately

notify doctor.

This package includes (Style of door sensor and chime may vary from illustration):

1. Remove orange battery tab from push

button. Remove back of case by pushing in

tab on bottom with a small screwdriver (see

Figure 1). Remove orange battery tab.

2. Install 3 alkaline “C” batteries (not includ-

ed) into chime base. Make sure batteries are

installed according to the diagram inside the

chime (see Figure 2).

IMPORTANT:To avoid resetting chime base

memory, wait 30 seconds before pressing

push button.See Troubleshooting, Problem

3if chime memory was accidentally reset.

3x - “C” TYPE BATTERIES

TYPE “C”

PRESS & HOLD

TUNE–1 SEC

SYNC–3 SEC

RESET–10 SEC

Figure 2

Chime base Chime cover Wireless push

button

Hardware

pack

Model

3x- “C” TYPE BATTERIES

PRESS&HOLD

TUNE–1SEC

SYNC–3SEC

RESET–10SEC

7611 ✔ ✔ ✔ ✔

7464 ✔ ✔ ✔ ✔

3. Test range. Temporarily position chime and

push button where you want them mounted.

Press push button to verify chime and push

button work properly (see Figure 3). If chime

does not sound, see Troubleshooting.

4. Adjust volume control. Turn volume control

knob on chime base to adjust volume.

5. Mount push button. Use either screws or

double sided tape to mount push button.

• Screw Mounting: To mount with screws,

remove back of case by pushing in tab

on bottom with a small screwdriver (see

Figure 1). Note: Remove material in screw

holes (if needed) before mounting with

screws. Attach back of case to door jamb

or wall (see Figure 4). Snap front of push

button on.

• Tape Mounting: When attaching push but-

ton using double-sided tape, make sure the

surface of the door jamb or wall is clean.

6. Rotate cover pin. Before mounting the chime

base to the wall, turn the base vertically or

horizontally (depending upon the chime cover)

and slide the cover pin out of the chime base.

Turn the pin over and slide the cover pin into

the chime base (see Figure 5).

7. Mount chime base. Using the “UP” arrow

indicator, place the chime base against the

wall and make sure it is level. Mark the four

screw hole locations on the mounting surface

(see Figure 6).Drill four 3/16 in. pilot holes and

insert wall anchors. Align the four screw holes

in the chime base with the wall anchors and

insert the four M3 x 30 mm screws. Tighten

securely.

8. Hang the chime cover on the cover pin on

the chime base.

Figure 4

Figure 3

Figure 5

Figure 6

3x - “C” TYPE BATTERIES

TYPE “C”

PRESS & HOLD

TUNE–1 SEC

SYNC–3 SEC

RESET–10 SEC

3x - “C”TYPE BATTERIES

TYPE “C”

PRESS& HOLD

TUNE–1SEC

SYNC–3SEC

RESET–10SEC

Tune Settings

Tune Setting Table

The chime has different selectable tunes: Ding

(one note tune), Ding-Dong (two note tune), or

Westminster (eight note tune). The factory set-

ting is for the Westminster tune. This tune can

be changed by following the instructions in the

Tune Setting Table.

Note: All chime models are designed to work with

up to 5 push buttons (sold separately).All chimes

are designed to play only two different tunes no

matter how many push buttons are used.

Chime Base

Inside Push Button

3x - “C” TYPE BATTERIES

TYPE “C”

PRESS & HOLD

TUNE–1 SEC

SYNC–3 SEC

RESET–10 SEC

Push Button Chime Tune

Jumper - ON ——— Ding

Jumper - OFF Press and release button on chime.

Listen for selected tune. Repeat to

select different tune.

Ding-Dong or

Westminster

Troubleshooting

1. PROBLEM: Chime does not sound or rang one time and quit.

A. POSSIBLE CAUSE: Push button and chime are not synced.

A. CORRECTIVE ACTION: Sync the push button and chime.

• Press and hold the button on the chime until the chime sounds a

“Beep-Beep”.

• Press the push button within 30 seconds. The chime will sound a

“Beep-Beep” tone to indicate the push button is synced.

• Press the push button to ensure operation.

B. POSSIBLE CAUSE: Batteries not installed correctly.

B. CORRECTIVE ACTION: Make sure batteries are installed according to

the diagram inside the push button and chime.

C. POSSIBLE CAUSE: Batteries are dead.

C. CORRECTIVE ACTION: Check charge of push button and chime bat-

teries and replace if necessary.

2. PROBLEM: Batteries seem okay, but the chime does not work after instal-

lation.

A. POSSIBLE CAUSE: Chime or push button is mounted on metal or near

metal studs. Note: Metal reduces transmission range.

A. CORRECTIVE ACTION: Use 1/4 in. to 1/2 in. (6 to 13 mm) wood shims

to move chime or push button away from metal surface.

B. POSSIBLE CAUSE: Chime is mounted near concrete ﬂoor or wall.Note:

Concrete may reduce range.

B. CORRECTIVE ACTION: Move chime away from concrete surface.

C. POSSIBLE CAUSE: Chime and push button are installed too far apart.

C. CORRECTIVE ACTION: Locate chime closer to push button.

3. PROBLEM: Chime sounds when not intended (false triggers).

POSSIBLE CAUSE: Chime is receiving interference from another wire-

less device.

CORRECTIVE ACTION: Reset chime.

• Remove push button battery. Wait 30 seconds.

• Press and hold the push button for 10 to 15 seconds within 60 seconds

after installing battery into the push button.

• Press and hold the button on the chime until the chime sounds a

“Beep-Beep-Beep-Beep”.

• To re-sync the push button and chime, press and hold the button on

the chime until the chime sounds a “Beep-Beep”.

• Press the push button within 30 seconds. The chime will sound a

“Beep-Beep” tone to indicate the push button is synced.

• Press the push button to ensure operation.

Note: The push button and chime come synced from the factory. The range of

the wireless chime can vary with location, temperature, and battery condition.

Learn more about home shop we have.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Heath Zenith Accessoires

Heath Zenith

Heath Zenith 6168 Manuel utilisateur

Heath Zenith

Heath Zenith SL-6153 Manuel utilisateur

Heath Zenith

Heath Zenith SECUR360 9600 Manuel utilisateur

Heath Zenith

Heath Zenith DUAL BRITE SL-5597 Manuel utilisateur

Heath Zenith

Heath Zenith SL-6168 Manuel utilisateur

Heath Zenith

Heath Zenith 29 Manuel utilisateur

Heath Zenith

Heath Zenith Wireless Push Button Accessory 598-1105-06 Manuel utilisateur

Heath Zenith

Heath Zenith notifi alert Manuel utilisateur

Heath Zenith

Heath Zenith Motion Sensing 3-Way Wall Switch 6107 Manuel utilisateur

Heath Zenith

Heath Zenith SL-6143 Manuel utilisateur

Heath Zenith

Heath Zenith DESA 6270 Manuel utilisateur

Heath Zenith

Heath Zenith 7868 Manuel utilisateur

Heath Zenith

Heath Zenith Lighted Wireless Push Button Accessory Manuel utilisateur

Heath Zenith

Heath Zenith SL-6155 Series Manuel utilisateur

Heath Zenith

Heath Zenith Wireless Push Button Accessory 598-1151-02 Manuel utilisateur

Heath Zenith

Heath Zenith 7797 Manuel utilisateur

Heath Zenith

Heath Zenith Decorative Wireless Chime 598-1000-07 Manuel utilisateur

Heath Zenith

Heath Zenith 6180 Series Manuel utilisateur

Heath Zenith

Heath Zenith Replacement Motion Sensor SH-5407 Manuel utilisateur

Heath Zenith

Heath Zenith Notifi Elite Manuel utilisateur

Heath Zenith

Heath Zenith Dual Brite SL-5597 Manuel utilisateur

Heath Zenith

Heath Zenith 598-1215-01 Manuel utilisateur

Heath Zenith

Heath Zenith 7309 Manuel utilisateur

Heath Zenith

Heath Zenith Single Entrance Chime 23/M Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur