Heath Zenith 7868 Manuel utilisateur

This chime requires 2 “C” alkaline batteries (not included). In typical use,

alkaline batteries will last up to one year.

Wireless Chime

Figure 2

Figure 1

WARNING: To prevent possible

SERIOUS INJURY or DEATH:

• NEVER allow small children near

batteries.

• If battery is swallowed, immediately

notify doctor.

This package includes (Style of door sensor and chime may vary from illustration):

1. Remove orange battery tab from push

button. Remove back of case by pushing in

tab on bottom with a small screwdriver (see

Figure 1). Remove orange battery tab.

2. Remove chime cover. Firmly pull on cover

to remove it from chime base (see Figure 2).

Chime

base

Chime cover Wireless push

button

Hardware

pack

Model

TYPE'C'

LR14

TYPE'C'

LR14

MODEL:WL-102D

SYNC– HOLD 3 SECONDS

RESET– HOLD 10 SECONDS

7868 ✔ ✔ ✔ ✔

7870 ✔ ✔ ✔ ✔

7871 ✔ ✔ ✔ ✔

TR-0095-RX

TYPE

TR-0095-RX

Battery Cover

Battery Cover Catch

TYPE 'C'

LR14

TYPE 'C'

LR14

MODEL: WL-102D

SYNC – HOLD 3 SECONDS

RESET – HOLD 10 SECONDS

3. Install 2 alkaline “C” batteries. Press in

catch on bottom of battery cover and lift to

remove (see Figure 3). Make sure batteries

are oriented properly (see Figure 4).

Test range. Temporarily position chime and

push button where you want them mounted.

Press push button to verify chime and push

button work properly. If chime does not sound,

see Troubleshooting.

5. Mount push button. Use either screws or

double sided tape to mount push button.

• Screw Mounting: To mount with screws,

remove back of case by pushing in tab on

bottom with a small screwdriver (see Figure

1). Note: Remove material in screw holes

(if needed) before mounting with screws.

Attach back of case to door jamb or wall (see

Figure 5). Snap front of push button on.

• Tape Mounting: When attaching push but-

ton using double sided tape, make sure the

surface of the door jamb or wall is clean.

6. Mount chime base. Determine mounting

location.

• Place chime against wall and verify the

chime is level. Note: See chime base for

correct orientation.

• Use all 4 chime mounting holes as a tem-

plate (see Figure 6).

• Drill 7/32" diameter pilot holes for wall an-

chors (provided) and insert anchors. Note:

Always use wall anchors if not mounting

directly into a stud.

• Verify chime is level and tighten screws

securely.

• Press chime cover onto chime base.

Figure 3

Figure 4

Figure 5

Figure 6

TR-0095-RX

TYPE

Inside Push Button

Tune Settings

Push Button Tune

Jumper - ON Ding

Jumper - OFF Ding-Dong

Tune Setting Table

The chime has different selectable tunes: Ding

(one note tune) or Ding-Dong (two note tune).

The factory setting is for the Ding-Dong tune.This

tune can be changed by following the instructions

in the Tune Setting Table.

Note: All chime models are designed to work with

up to 5 push buttons (sold separately).All chimes

are designed to play only two different tunes no

matter how many push buttons are used.

Troubleshooting

1. PROBLEM: Chime does not sound.

A. POSSIBLE CAUSE: Batteries not installed correctly.

A. CORRECTIVE ACTION: Make sure batteries are installed according to

the diagram inside the push button and chime.

B. POSSIBLE CAUSE: Batteries are dead.

B. CORRECTIVE ACTION: Check charge of push button and chime bat-

teries and replace if necessary.

C. POSSIBLE CAUSE: Push button and chime are not synced.

C. CORRECTIVE ACTION: Sync the push button and chime.

• Press and hold the button on the chime until the chime sounds a

“Beep-Beep”.

• Press the push button within 30 seconds. The chime will sound a

“Beep-Beep” tone to indicate the push button is synced.

• Press the push button to ensure operation.

2. PROBLEM: Batteries seem okay, but the chime does not work after instal-

lation.

A. POSSIBLE CAUSE: Chime or push button is mounted on metal or near

metal studs. Note: Metal reduces transmission range.

A. CORRECTIVE ACTION: Use 1/4 in. to 1/2 in. (6 to 13 mm) wood shims

to move chime or push button away from metal surface.

B. POSSIBLE CAUSE: Chime is mounted near concrete ﬂoor or wall.Note:

Concrete may reduce range.

B. CORRECTIVE ACTION: Move chime away from concrete surface.

C. POSSIBLE CAUSE: Chime and push button are installed too far apart.

C. CORRECTIVE ACTION: Locate chime closer to push button.

3. PROBLEM: Chime sounds when not intended (false triggers).

POSSIBLE CAUSE: Chime is receiving interference from another wire-

less device.

CORRECTIVE ACTION: Reset chime and push button.

• Remove push button batteries. Wait 30 seconds.

• Press and hold the push button for 10 to 15 seconds within 60 seconds

after installing battery into the push button.

• Press and hold the button on the chime until the chime sounds a

“Beep-Beep-Beep-Beep”.

• To re-sync the push button and chime, press and hold the button on

the chime until the chime sounds a “Beep-Beep”.

• Press the push button within 30 seconds. The chime will sound a

“Beep-Beep” tone to indicate the push button is synced.

• Press the push button to ensure operation.

Note: The push button and chime come synced from the factory. The range of

the wireless chime can vary with location, temperature, and battery condition.

TYPE 'C'

LR14

TYPE 'C'

LR14

MODEL: WL-102D

SYNC – HOLD 3 SECONDS

RESET – HOLD 10 SECONDS

Learn more about home shop we have.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Heath Zenith Accessoires

Heath Zenith

Heath Zenith Notifi Elite Manuel utilisateur

Heath Zenith

Heath Zenith 7762 Manuel utilisateur

Heath Zenith

Heath Zenith Motion Sensing 3-Way Wall Switch 6107 Manuel utilisateur

Heath Zenith

Heath Zenith SECUR360 9600 Manuel utilisateur

Heath Zenith

Heath Zenith 6168 Manuel utilisateur

Heath Zenith

Heath Zenith SL-6155 Series Manuel utilisateur

Heath Zenith

Heath Zenith notifi alert Manuel utilisateur

Heath Zenith

Heath Zenith 5610 Manuel utilisateur

Heath Zenith

Heath Zenith 7750 Manuel utilisateur

Heath Zenith

Heath Zenith InTune MP3 Door Chime Manuel utilisateur

Heath Zenith

Heath Zenith DualBrite Replacement Sensor Head 2LBN3 Manuel de service

Heath Zenith

Heath Zenith Wireless Strobe Chime 6144 Manuel utilisateur

Heath Zenith

Heath Zenith Wireless Dual Push Button Accessory SL-6200 Manuel utilisateur

Heath Zenith

Heath Zenith Wireless Push Button Accessory SL-6190... Manuel utilisateur

Heath Zenith

Heath Zenith Wireless Chime 6153/62/71/72 Manuel utilisateur

Heath Zenith

Heath Zenith HZ-1802-BK-A Manuel utilisateur

Heath Zenith

Heath Zenith DualBrite Manuel utilisateur

Heath Zenith

Heath Zenith Notifi elite Manuel utilisateur

Heath Zenith

Heath Zenith Secure Home 5215 Manuel utilisateur

Heath Zenith

Heath Zenith SL-6166 Manuel utilisateur

Heath Zenith

Heath Zenith SL-7464-03 Manuel utilisateur

Heath Zenith

Heath Zenith 121AC Manuel utilisateur

Heath Zenith

Heath Zenith 121AC Manuel utilisateur

Heath Zenith

Heath Zenith 7311 Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur