Gofanco HDMIExt4P Manuel utilisateur

4-Port HDMI Extender/Splitter

over CAT5e/6 with IR - 40M

G4-0022A

P/N: HDMIExt4P

Congratulationsforowningagofancoproduct.Ourproducts

aim to meet all your connectivity needs wherever you go.

Have fun with our products!

Please read this manual carefully before first use.

If you need more information about our products, please

visit www.gofanco.com.

For technical support, please email us at support@gofanco.

com.

For drivers/manuals download, please go to http:// www.

gofanco.com/download.

Introduction

gofanco 4-Port HDMI Extender/Splitter over CAT5e/6 with IR

- 40M (part# HDMIExt4P) extends HDMI signals to four

monitors over Cat5e/6 up to 40m with 1080p.

Specifications

Package Contents

• 4-Port HDMI Extender/Splitter over CAT5e/6 with IR -

40M (1x TX & 4x RXs)

• 5x Power adapters

• IR Blaster extension cable & IR Receiver extension cables

• Screw kit

• User's guide

Output Signal HDMI

Protocol HDbitT

Resolution Up to 1080p

Transmission

Distance Up to 40m (130ft)

Network Cable CAT5e/6

(CAT6 recommended)

HDMI Cable Up to 5m (Input & Output)

Power Supply TX: DC 5V/3A, RX: DC 5V/1A

IR Signal 20~60KHz IR devices supported

•Power Jack: Connect the included 5V/3A DC power

adapter here

•EDID : The HDMI source device reads EDID information

from the TX unit, and outputs it to the RXs.

Please refer to the settings below.

Layout

Power Jack

Figure 1: Transmitter (TX)

HDMI In

IR Out

RJ45

* 6: Default setting

EDID RJ45

Figure 2: Transmitter (TX)

Link LED

•Link LED: Turns red when powered. Turns blue when

there is an HDMI signal detected

•Reset: Press to reset if HDMI Extender doesn't work

properly

•IR Out: Infrared 3.5mm socket. Plug IR Blaster extension

cable here. See instructions on page 7.

•RJ45 (1): Link to Receiver 1's RJ45 via a Cat5e/6 cable

•RJ45 (2): Link to Receiver 2's RJ45 via a Cat5e/6 cable

•HDMI In: Connect your HDMI source here with an HDMI

cable (cable not included)

•RJ45 (3): Link to Receiver 3's RJ45 via a Cat5e/6 cable

•RJ45 (4): Link to Receiver 4's RJ45 via a Cat5e/6 cable

Reset

Power jack

•Power Jack: Connect the included 5V/1A DC power

adapter here

•HDMI Out: Connect your HDMI display here with an

HDMI cable (cable not included)

•IR In: Infrared 3.5mm socket. Plug IR Receiver extension

cable here. See instructions on page 7.

IR InHDMI Out

Figure 4: Receiver (RX) - HDMI Display Output

Reset

•Reset: Press to reset if HDMI Extender doesn't work

properly

•RJ45: Link to the Transmitter's RJ45 via a Cat5e/6 cable

•Link LED: Blinks when powered on. ON when the Cat5e/

6 cable is connected/linked properly between the

Transmitter and Receiver

Figure 3: Receiver (RX) - RJ45 Input

RJ45 Link LED

IR Extenders

•IR Blaster: Plug into the Transmitter's IR 3.5 socket to

emit IR signals.

•IR Receiver: Plug into the Receiver's IR 3.5 socket to

receive IR signals from a remote control (for the HDMI

device connected to the Transmitter).

Note: Incorrect placement of the IR Blaster and IR

Receiver may result in failure of these cables. Please

check carefully before plugging in the IR cables to

proper IR sockets.

Figure 5: IR Blaster

(Connect to Transmitter TX)

Figure 6: IR Receiver

(Connect to Receiver RX)

Hardware Installation

Note: To achieve optimal performance, CAT6 cable is

recommended.

1. Power off all devices including your HDMI source and

display.

2. Connect your HDMI source to the Transmitter's HDMI

IN connector.

3. Optional: Connect the IR Blaster extension cable to the

Transmitter's IR Out. Face the eye towards your HDMI

device's IR window.

4. Connect your HDMI display to the Receiver's HDMI OUT

connector with an HDMI cable (not included). Repeat

this step for all Receivers.

5. Optional: Connect the IR Receiver extension cable to the

Receiver's IR In. Repeat this step for all Receivers.

6. Switch the EDID according to your desired HDMI signal

format. Refer to page 4 for details.

7. Connect and link the Transmitter and Receivers by

CAT5e/6 cables.

8. Plug the included power adapters into the Transmitter's

and Receivers' Power Jacks, then plug all power

adapters into reliable power outlets.

9. Power on your HDMI device and HDMI displays.

10. The HDMI Extender is ready for use.

Application

Easily extends HDMI signals such as DVD players or

computers to four remote displays simultaneously . An

ideal solution for exhibitions, video conferences, show

centers, and etc..

HDMI IN

Figure 7

* When using the remote control, please make sure its

distance to the IR Receiver extension cable is within 5

meters (16.4 ft) and without obstructions.

CAT5e/6 cable

FAQ & Solutions

Q: There is no picture on the TVs:

A: 1) Check whether the correct TV input is selected.

2) Check whether the "Link" LED on TX and RXs are on.

If the RX's Link LED blinks, it means the RX doesn't receive

signals from the TX.

3) Make sure the resolution of the input HDMI source is

supported by this Extender/Splitter.

Q: There is unstable picture on the TVs:

A: 1) Switch the "EDID" to the appropriate position, refer to

page 4 for details.

2) Unplug the Cat5e/6 cable and plug in again.

If the issue still exists, use other Cat5e/6 cables.

Q: Only one TV has image:

A: 1) Make sure the CAT cables and HDMI cable are

connected correctly and securely.

2) Press the "Reset" button on the TX to re-identify the

HDMI signal.

3) Unplug the Cat5e/6 cable and plug in again.

Table des matières

Autres manuels gofanco Extenseur

gofanco

gofanco Prophecy PRO-HDExtIP-TX Manuel utilisateur

gofanco

gofanco HDMIExtSplit Manuel utilisateur

gofanco

gofanco KVMHD20Ext Manuel utilisateur

gofanco

gofanco HDBaseT4P-4K Manuel utilisateur

gofanco

gofanco HD20Ext4P-LT Manuel utilisateur

gofanco

gofanco HDbitT4K Manuel utilisateur

gofanco

gofanco HDBaseT-HD20 Manuel utilisateur

gofanco

gofanco HDwireless200 Manuel utilisateur

gofanco

gofanco HDbitTPro Manuel utilisateur

gofanco

gofanco HDbitT4P Manuel utilisateur

gofanco

gofanco HDwireless150 Manuel utilisateur

gofanco

gofanco 4K120 Manuel utilisateur

gofanco

gofanco USBCwireless Manuel utilisateur

gofanco

gofanco HDExt Manuel utilisateur

gofanco

gofanco HDbaseT-HDR Manuel utilisateur

gofanco

gofanco AudioCATExt Manuel utilisateur

gofanco

gofanco HDExtIP4K Manuel utilisateur

gofanco

gofanco HDBITT4K22 Manuel utilisateur

gofanco

gofanco HDwireless100 Manuel utilisateur

gofanco

gofanco G4-0014A Manuel utilisateur

gofanco

gofanco HDBaseT Manuel utilisateur

gofanco

gofanco HDwireless1x4 Manuel utilisateur

gofanco

gofanco HDExt50 Manuel utilisateur

gofanco

gofanco HDExt24-HD20 Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur

gofanco HDMIExt4P Manuel utilisateur

Manuels Extenseur populaires d'autres marques