GE 33712 Manuel utilisateur

Universal Remote

Instruction Manual

Control Remoto Universal

Manual de Instrucciones

33712

61772/17 V2

Introduction..................................................................................... 2

Setup .................................................................................................. 3

Button Functions .......................................................................... 4

Programming Your Remote..................................................... 6

Direct Code Entry................................................................... 6

Auto Code Search ................................................................. 8

Controlling Combo Devices.............................................. 9

Using Your Remote ....................................................................10

Master Volume Feature....................................................10

Code Identiﬁcation .............................................................11

Reset to Factory Settings.................................................11

Troubleshooting..........................................................................12

Warranty ........................................................................................13

FCC Statement.............................................................................14

Table of Contents

Scan this to view

a helpful remote

setup video

http://www.byjasco.com/remote

Congratulations on your purchase of this GE-branded

Universal Remote Control. This remote is capable of

operating thousands of audio/video devices including

TVs, Blu-ray™/DVD players, streaming media players,

sound bars, cable receivers and more!

SAVE THIS MANUAL AND CODE LIST

FOR FUTURE REFERENCE

Setup

Your universal remote requires two (2) AA batteries

(not included). Alkaline batteries are recommended.

Battery Installation

1. On the back of the remote, pull down on

the textured surface and slide battery cover

downward to remove.

2. Match the (+) and (-) marks on the batteries to the

(+) and (-) marks inside the battery compartment,

then insert two (2) AA batteries. Be sure to use

fresh batteries.

3. Position battery cover slightly below opening and

push upward to lock into place.

NOTE: If your remote stops operating properly, replace

the batteries with new ones.

Battery Precautions

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon-zinc), or

rechargeable (Ni-Cd, Ni-MH, etc.) batteries.

• Always remove old, weak or worn-out batteries

promptly and recycle or dispose of them in

accordance with local and national regulations.

Battery Saver

Your remote automatically turns off if the buttons are

depressed more than 8 seconds. This will save your

batteries should your remote get stuck in a place

where the buttons remain depressed (e.g., between

the sofa cushions).

Code Saver

You have up to 10 minutes to change the batteries

in your remote without losing the codes you have

programmed.

Button Functions

cbl dvd aud

strm

app1 app2

b-ray

Button Functions

1. Power - turns devices On/Off

2. Input - Select video inputs

3. TV, strm, b-ray, cbl, dvd, aud - Selects the device

to control

4. Home/Guide - Easily access features on today's

streaming devices, or Guide on cable/satellite

receivers

5. Menu - Displays the on-screen menu

6. Exit - Exit on-screen menus

7. Mute - Mutes sound

8. Setup - Used to program the remote

9. Previous Channel - Returns to the previously

selected channel

10. Up/Down/Left/Right menu navigation; Volume

up/down; Channel up/down

11. Ok - Selects menu items for the controlled device

12. DVD/Blu-ray™open/close - open/close a player,

or List features on cable/satellite receivers

13. Info - Displays on-screen show/content

information

14. Streaming App Hotkeys - Access top apps like

Netﬂix®, Amazon®Prime, Hulu®and more

15. Record, play, stop, rewind, fast forward, pause

16. Numbers - Enter numbers for direct channel

selection

17. Dot (•) - Used to select digital channels, e.g., 4.1

18. Enter - Some devices require enter to be pressed

after channel selection

Programming Your Remote

Your remote is designed to control multiple audio/video

devices. To use, you will need to program the remote for

your devices. There are two different methods you can

use to program the remote, Direct Code Entry or Auto

Code Search.

• The Direct Code Entry method is the recommended

method as it is the simplest and quickest method in

most cases.

• The Auto Code Search method searches through all

the codes in the remote to ﬁnd a code for

your device.

Note: this remote comes preprogrammed for Roku®boxes and

Samsung TVs. Press TV for Samsung TVs and strm for Roku boxes.

Direct Code Entry (Recommended)

1. Locate the Code List included with

your remote. Find the section for the

type of device you wish to control,

(for example TV, strm, b-ray, cbl, dvd,

aud). Locate the brand of your device

and circle all the remote codes for

the brand.

2. Press and hold down the SETUP button

on the remote until the red light on the

remote control turns on. Release the

SETUP button. The red light will

remain on.

Note: The red light will either be a small light at the

top of the remote or the power on/off button.

3. Press and release the device button on

the remote for the type of device you

wish to control, (for example TV, strm,

b-ray, cbl, dvd, aud). The red light will

blink once and remain on.

Note: Any of the device buttons on the remote can

be programmed to control any of your devices. For

example, you can use the CBL device button on

the remote to control a Satellite Receiver, Digital

Converter Box, Streaming Media Player or any

device category in the Code List.

Programming Your Remote

4. Use the number buttons on the remote

to enter the ﬁrst 4-digit remote code

you circled in the Code List in Step 1.

The red light will turn off after entering

the fourth digit.

5. Point the remote at the device. Test

the buttons on the remote to see if the

device responds as you would expect. If

the buttons do not operate the device,

return to Step 2 above and use the next

code that you circled for that device.

6. Repeat steps 1 – 5 for each device you wish to

control.

Programming Notes

• Some codes may operate only a few functions of your

device. There may be another code in the Code List

that controls more functions. Test other codes in the

Code List for more functionality.

• If you do not ﬁnd a remote code that works your

device or there are no codes in the Code List for your

device, use the Auto Code Search method in the next

section to program your remote.

• For combination devices such as a TV/DVD combo

or TV/ VCR combo, you may have to enter a code for

each device. (See Controlling Combo Devices, pg. 9.)

• Write down the remote codes used to program the

remote for future reference.

Programming Your Remote

Note: The red light will either be a small light at the

top of the remote or the power on/off button.

3. Press and release the device button on the

remote for the type of device you wish to

control, (for example TV, strm, b-ray, cbl,

dvd, aud). The red light will blink once and

remain on.

4. With the remote pointed at the device,

press and release the POWER button

on the remote. The remote will send 10

different codes to the device. The red light

will blink once for each code and remain

on after sending the 10 codes.

Did the device turn off?

• If YES, go to Step 5.

• If NO, repeat Step 4 to test the next

10 codes.

5. Manually turn the device back on.

6. With the remote pointed at the device,

press and release the VOL + button. The

remote will re-send the ﬁrst code of the 10

codes from Step 4. The red light will blink

once and remain on.

Auto Code Search

The Auto Code Search is a process where you can

search through all the codes stored in the remote to ﬁnd

a code for your device. It is recommended that you read

through all the steps below to familiarize yourself with

the Auto Code Search before starting the process.

1. Manually turn on the device you wish

to control.

Note: The Auto Code Search process cannot be used

for devices without power on/off capability. Use the

Direct Code Entry method in these cases.

2. Press and hold down the SETUP button on

the remote until the red light on the remote

control turns on. Release the SETUP button.

The red light will remain on.

Programming Your Remote

Did the device turn off?

• If YES, you have found a code for the

device. Press and release the same device

button you pressed in Step 3. This will

store the code in the remote. Go to step 7.

• If NO, continue to press and release the

VOL + button until the device turns off to

test the other 9 codes from Step 4.

Be sure to wait approximately 3 seconds

after each VOL + button press to allow

the device time to respond to the code.

When the device turns off, you have

found a code for your device. Press and

release the same device button pressed

in Step 3. This will store the code in the

remote. Go to Step 7.

Notes:

• The VOL – button can be used to go backwards through

each batch of 10 codes.

• The red indicator light will ﬂash 2 times after testing the

ﬁrst or last code in each batch of 10.

7. Use the remote to turn the device back on.

Test the buttons on the remote to see if the

device responds as you would expect. If the

buttons do not operate the device, return to

Step 2 and repeat this process to search for a

better code to operate the device.

8. Repeat this process for each device you wish

to control.

Controlling Combo Devices

Some combo devices (e.g. TV/VCR, TV/DVD, DVD/VCR,

etc.) will require you to set up two different device

buttons to control both parts of the combo device.

For example, if you have a TV/DVD combo, you may

need to set up one code under the TV button to

control the TV and a separate code under the dvd

button to control the DVD.

Using Your Remote

aud

Master Volume Feature

The Master Volume Feature allows you to select a

single device that the volume buttons always control.

For example, the remote can be in TV mode while

the volume buttons control the volume on your audio

receiver or sound bar instead of your TV.

Enabling the Master Volume Feature

1. Press and hold down the SETUP button

on the remote until the red light on the

remote control turns on. Release the

SETUP button. The red light

will remain on.

2. Press and release the device button

(TV, aud, etc.) on the remote for the

device you wish to control the volume.

3. Press and release the MUTE button.

4. Press and release the VOL+ button.

The red light will blink twice and

turn off.

Disabling the Master Volume Feature

1. Press and hold down the SETUP button

on the remote until the red light on the

remote control turns on. Release the

SETUP button. The red light will

remain on.

2. Press and release the device button

(TV, aud, etc.) programmed to control

the Master Volume Feature.

3. Press and release the MUTE button.

4. Press and release the VOL - button.

The red light will blink twice and

turn off.

Table des matières

Langues :

Manuels Télécommande universelle populaires d'autres marques

Pronto

Pronto Peel Manuel utilisateur

Radio Shack

Radio Shack Wireless Remote Control System Manuel utilisateur

AUVIO

AUVIO Universal Home Theater Remote Manuel utilisateur

Philips

Philips Icon SRU4106 Manuel utilisateur

THOMSON

THOMSON ROC4309 Manuel utilisateur

Philips

Philips pm625S Manuel utilisateur

RCA

RCA RCU600WMS - Universal Remote Control Manuel utilisateur

Blackweb

Blackweb BWB17AV002 Manuel utilisateur

Marmitek

Marmitek DoorGuard 300 Manuel utilisateur

Chunghop

Chunghop RM-L618 Manuel utilisateur

Anderic

Anderic KTN828 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. Touch Screen Remote Control Manuel utilisateur

Medion

Medion E74023 Manuel utilisateur

intensity

intensity RM02A Manuel utilisateur

Sky

Sky MY Manuel utilisateur

RCA

RCA RCU600M - Universal Remote Control Manuel utilisateur

Savant

Savant SUR-0500 Guide de référence rapide

GDI

GDI GDI-WT2K Manuel utilisateur