Future Automation PLH Manuel utilisateur

ISSUE: 006

www.futureautomation.co.uk

FUTURE

AUTOMATION

PLH

Plasma Lift Hinge Mechanism

Instruction Sheet

Your Pack

Should Contain

1 PLH -

Plasma Lift Hinge

Mechanism

Suitable for

26" to 50"

screens

1 Standard PL

Fixtures Pack

The contents

of which can be

found on Sheet 17

1 IR

Remote Control

Sheet 1 of 17

ISSUE: 006

www.futureautomation.co.uk

FUTURE

AUTOMATION

PLH

Plasma Lift Hinge Mechanism

Instruction Sheet

WARNING

Mechanisms which lift

or move weights need

to be checked on a

yearly basis for any

damage which may

result in an accident

IMPORTANT

It is the responsiblity of

the installer to warn all

potential end users of

the dangers of interfering

with mechanisms during

operation

Stage 1

Check T

he O

peration O

f T

he M

echanism

OUT: Reveal Screen

IN: Hide Screen

STOP: Stops Mechanism

See SHEET 11 for further

controls

Connect the supplied IR

remote and check that the

mechanism operates

correctly before continuing

with the installation.

CONTROLS

Firstly, remove the

cable ties that keep the

mechanism safe and

secure during transit.

There are usually 6 ties

in various locations.

However, on some models

there may be more than

6 cable ties.

Once all the cable ties

have been removed, then

the mechanism can be

powered up and tested.

Sheet 2 of 17

ISSUE: 006

www.futureautomation.co.uk

FUTURE

AUTOMATION

PLH

Plasma Lift Hinge Mechanism

Instruction Sheet

Aluminum

Flap

6mm Flap

125

107

DETAIL A

SCALE 1 : 5

Remove mount and place base

central onto the beam into position

and reattach the mount.

Fix the base by using penny washers

and wood screws through the

base supports

provided as

shown in

tail A

Woodscrew

Penny

asher

Base

upports

Stage 2

Fitting Flap And Base To Mechanism

FIXING

Make sure the base panel

lines up squarely, directly

on top of the lifting beam.

Consult

PLH TECHNICAL SHEET

before fabricating any

flaps or base panels.

The hole is necessary for hinge pole to pass through.

The 6mm flap and the base should be

made as part of the cabinet.

The surface of the flap should be

varnished or painted to prevent warping.

Take care when fixing the surfaces

together. Place the objects on a

flat surface to make sure the edges

are properly aligned when they

come into contact.

Try to use as many self

adhesive pads as possible

to get the most secure fixture.

VIEWING SIDE

Sheet 3 of 17

ISSUE: 006

www.futureautomation.co.uk

FUTURE

AUTOMATION

PLH

Plasma Lift Hinge Mechanism

Instruction Sheet

DETAIL B

SCALE 2 : 3

Stage 3

Fixing T

he L

ift In T

he C

abinet

Place the mechanism within the cabinet.

Raise the beam to the top and guide the

base carefully through the opening in the top.

With the base properly located, use the 8

pointed screws supplied, 4 on each side,

to pin the mechanism in place, fixing its

position left and right. These 8 screws

should be screwed through the middle

hole of each of the clusters of 3,

shown below right.

With the lift fixed in position, use 8 wood

screws on each side to secure the

lift to the cabinet.

Sheet 4 of 17

ISSUE: 006

www.futureautomation.co.uk

FUTURE

AUTOMATION

PLH

Plasma Lift Hinge Mechanism

Instruction Sheet

DETAIL C

SCALE 1 : 1

By adjusting the screw up

and down, you can adjust

the stop height of the beam,

and also the base panel.

Stage 4

Adjusting Base Panel Height

Sheet 5 of 17

ISSUE: 006

www.futureautomation.co.uk

FUTURE

AUTOMATION

PLH

Plasma Lift Hinge Mechanism

Instruction Sheet

DETAIL C

SCALE 1 : 3

Stage 5

Positioning The Base Panel

There should be a gap of about 3mm

around the edges of the base panel to

the cabinet.

See Stage 2 for instructions on fixing

the base.

CABLES

The cables for the screen

should pass up through

the pole up to behind

the plasma screen.

Sheet 6 of 17

ISSUE: 006

www.futureautomation.co.uk

FUTURE

AUTOMATION

PLH

Plasma Lift Hinge Mechanism

Instruction Sheet

Adjusting T

he F

lap-Up

osition

Stage 6

By adjusting the white screw,

at each side of the lift, you can

adjust the tilt of the flap.

By winding the push rods on each side, you can

adjust the height of the flap in order to get it level

with the cabinet top. Be sure to lock the nut securely

once adjusted. Make sure the black plate does not

touch the inside of the cabinet. This can cause

strain on the motor, leading to failure.

CABINET TOP - SIDE VIEW

By loosening the M6 bolts on each

side under the flap, you can adjust

the position of the flap in the hole

in the cabinet top. Aim for a

3mm gap all round.

CABINET TOP - PLAN VIEW

CABINET TOP - SIDE VIEW

Sheet 7 of 17

ISSUE: 006

www.futureautomation.co.uk

FUTURE

AUTOMATION

PLH

Plasma Lift Hinge Mechanism

Instruction Sheet

DETAIL D

SCALE 1 : 4

By adjusting the bolts under each flap arm as circled,

it is possible to alter the angle the flap opens to. It is

very important that when the flap is open, it rests

in a vertical position, as shown above.

Stage 7

ecking F

lap

own P

osition

Sheet 8 of 17

ISSUE: 006

www.futureautomation.co.uk

FUTURE

AUTOMATION

PLH

Plasma Lift HingeMechanism

Technical Sheet

Carefully hook the screen with

the uprights properly secured

back onto the mounting frame

and position.

Stage 8

Fixing the screen to the lift

Simply mount the screen on to the mount supplied

with your mechanism. The example below

shows a Group A framework.

CABLES

When the screen is in the

home position, pass the cables

through

into the cabinet.

Once inside locate the cable

management system as circled

in the drawing. The cables can

be pushed inside to keep them

neat within the cab

inet

Place screen down carefully onto a

flat surface, remove uprights from

the mount and bolt onto the back of

the screen.

Sheet 9 of 17

ISSUE: 006

www.futureautomation.co.uk

FUTURE

AUTOMATION

PLH

Plasma Lift Hinge Mechanism

Instruction Sheet

Table des matières

Autres manuels Future Automation Support TV

Future Automation

Future Automation PS32-M Manuel utilisateur

Future Automation

Future Automation PS60 Manuel utilisateur

Future Automation

Future Automation PS-VESA Series Manuel utilisateur

Future Automation

Future Automation DA Manuel utilisateur

Future Automation

Future Automation PS42 Manuel utilisateur

Future Automation

Future Automation PS Series Manuel utilisateur

Future Automation

Future Automation PS65-M Mode d’emploi

Future Automation

Future Automation PS55-M Mode d’emploi

Future Automation

Future Automation TTR60 Manuel utilisateur

Future Automation

Future Automation PS80-M Manuel utilisateur

Future Automation

Future Automation PS42 Manuel utilisateur

Manuels Support TV populaires d'autres marques

Ergotron

Ergotron Neo Flex Cantilever UHD Manuel utilisateur

StarTech.com

StarTech.com FPCEILBTB Manuel utilisateur

VonHaus

VonHaus 05/038 Manuel utilisateur

Techlink

Techlink ECHO TV Manuel utilisateur

Sandstrom

Sandstrom SSTVMC12X Manuel utilisateur

Sony

Sony SU-WL700 Mode d’emploi

ICW

ICW SCACC18 Manuel utilisateur

LG WM-L640V Manuel utilisateur

Gembird

Gembird WM-65ST-01 Manuel utilisateur

ERARD

ERARD FiTUP XXL 035320 Manuel utilisateur

PEERLESS

PEERLESS PLCK-1 Mode d’emploi

Kanto

Kanto RCF180 Manuel utilisateur

GEM

GEM GEM GP001 Manuel utilisateur

Gladiator Joe

Gladiator Joe GJ0A0053 Manuel utilisateur

Vivotek

Vivotek AM-105 Manuel utilisateur

Vivo

Vivo VESA STAND-VAD1B Manuel utilisateur

AmazonBasics

AmazonBasics B07QG3LMG4 Manuel utilisateur

Secura

Secura QLF210 Manuel utilisateur