Fujitsu MAH3182MC SERIES Manuel utilisateur

C141-E103-01EN

MAH3182MC/MP SERIES

MAH3091MC/MP SERIES

MAJ3364MC/MP SERIES

MAJ3182MC/MP SERIES

MAJ3091MC/MP SERIES

DISK DRIVES

PRODUCT/MAINTENANCE MANUAL

C141-E103-01EN i

REVISION RECORD

Edition Date published Revised contents

01 Feb., 2000

Specification No.: C141-E103-**EN

The contents of this manual is subject to

change without prior notice.

This page is intentionally left blank.

C141-E103-01EN iii

FOR SAFE OPERATION

Handling of This manual

This manual contains important information for using this product. Read thoroughly before using

the product. Use this product only after thoroughly reading and understanding especially the

section “Important Alert Items” in this manual. Keep this manual handy, and keep it carefully.

FUJITSU makes every effort to prevent users and bystanders from being injured or from suffering

damage to their property. Use the product according to this manual.

(Proceed to the Copyright Page)

iv C141-E103-01EN

Related Standards

Specifications and functions of products covered by this manual comply with the following

standards.

Standard (Text) No. Name Enacting Organization

ANSI X3.131-1986 American National Standard for

Information Systems—Small Computer

System Interface (SCSI)

American National

Standards Institute

(ANSI)

ANSI X3.131-1994 American National Standard for

Information Systems—Small Computer

System Interface - 2(SCSI-2)

American National

Standards Institute

(ANSI)

X3T9.2/85-52 Rev 4.B COMMON COMMAND SET (CCS)

of the Small Computer

System Interface (SCSI)

American National

Standards Institute

(ANSI)

X3T9.2/855D Rev 12 WORKING DRAFT Information

Technology SCSI-3 Parallel Interface American National

Standards Institute

(ANSI)

T10/1236-D Rev 12 WORKING DRAFT Information

technology SCSI Primary Commands-2

(SPC-2)

American National

Standards Institute

(ANSI)

ANSI NCITS 306-199x American National Standard for

Information Technology—SCSI-3 Block

Commands (SBC)

American National

Standards Institute

(ANSI)

X3T10/994D Rev 18 WORKING DRAFT Information

technology SCSI-3 Architecture Model

(SAM)

American National

Standards Institute

(ANSI)

T10/1302D Rev 11 WORKING DRAFT Information

technology SCSI Parallel Interface-3

(SPI-3)

American National

Standards Institute

(ANSI)

C141-E103-01EN v

PREFACE

This manual describes the MAH3182MC/MP, MAH3091MC/MP (hereafter, MAH series) and

MAJ3364MC/MP, MAJ3182MC/MP, MAJ3091MC/MP (hereafter, MAJ series), 3.5 type fixed disk drives

with an embedded SCSI controller.

This manual details the specifications and functions of the above disk drive, and gives the requirements and

procedures for installing it into a host computer system.

This manual is written for users who have a basic understanding of fixed disk drives and their use in

computer systems. The MANUAL ORGANIZATION section describes organization and scope of this

manual. The need arises, use the other manuals.

Chapter 1 GENERAL DESCRIPTION

This chapter introduces the MAH series and MAJ series disk drives and discusses their standard features,

hardware, and system configuration.

Chapter 2 SPECIFICATIONS

This chapter gives detailed specifications of the MAH series and MAJ series disk drives and their

installation environment.

Chapter 3 DATA FORMAT

This chapter describes the data structure of the disk, the address method, and what to do about media

defects.

Chapter 4 INSTALLATION REQUIREMENTS

This chapter describes the basic physical and electrical requirements for installing MAH series and MAJ

series disk drives.

Chapter 5 INSTALLATION

This chapter explains how to install MAH series and MAJ series disk drives. It includes the notice and

procedures for setting device number and operation modes, mounting the disk drive, connecting the cables,

and confirming drive operation.

Chapter 6 DIAGNOSIS and MAINTENANCE

This chapter describes the automatic diagnosis, and maintenance of MAH series and MAJ series disk drive.

This chapter also describes diagnostic methods for operation check and the basics of troubleshooting the

disk drives.

Chapter 7 ERROR ANALYSIS

This chapter describes in details how collect the information for error analysis and how analyze collected

error information.

Chapter 8 PRINCIPLE OF OPERATION

This chapter explains disk drives configuration and operation of MAH series and MAJ series.

vi C141-E103-01EN

APPENDIX A to D

The appendixes give supplementary information, including the locations of mounting setting terminals and

connectors, a list of setting items, the signal assignments of interface connectors, lists of model names and

product numbers, and SCSI interface functions.

The model numbers have a suffix that describes the electrical requirements of the SCSI interface between

host system and disk drive, the data formatted at the factory and device type.

CONVENTIONS

This manual uses the following conventions for alerts to prevent physical or property damages to users or

by standards.

DANGER

DANGER indicates that personal injury will occur if the user does not perform the procedure correctly.

WARNING

WARNING indicates that personal injury could occur if the user does not perform the procedure

correctly.

CAUTION

CAUTION indicates that either minor or moderate personal injury may occur if the user does not

perform the procedure correctly.

NOTICE

NOTICE indicates that inconvenience to the user such as damages to the product, equipment, data, and/or

other property may occur if the user does not pay attention or perform the procedure correctly.

IMPORTANT

IMPORTANT indicates information that the helps the user use the product more effectively.

Indicates

C141-E103-01EN vii

This manual indicates;

Decimal number: Indicates as it is.

Hexadecimal number: Indicates as X’17B9’, 17B9h, or 17B9H

Binary number: Indicates as “010”

DISCLAIMER

Failure of the MAH series and MAJ series intelligent disk drive is defined as a failure requiring

adjustments, repairs, or replacement. Fujitsu is not responsible for drive failures caused by misuse by the

user, poor environmental conditions, power trouble, host problems, cable failures, or any failure not caused

by the drive itself.

The suffix of the model name of the disk drive varies depending on the electrical requirements, capacity,

and data format at factory shipment of the SCSI, i.e., the interface for connecting the three device types or

host system and the disk drives (Note 1). However, in this manual, the typical model names (Note 2) are

used unless otherwise noted. These disk drives may be called intelligent disk drives (IDD), drives, or

devices in this manual.

Note 1: Model names

M AJ 3 364 MC

Interface types MC: LVD, 16-bit SCSI SCA2 connector 160MHz transfer

MP: LVD, 16-bit SCSI 68 pin connector 160MHz transfer

Formatted capacity (100 MB units)

Disk drive size 3: 3.5 type. Hand Disk Drive

Type AH: Number of rotations 7,200min-1 (7,200rpm)

AJ: Number of rotations 10,025min-1 (10,025rpm)

Note 2: Type model name

Type model name Model name

MAH3182 MAH3182MC, MAH3182MP

MAH3091 MAH3091MC, MAH3091MP

MAJ3364 MAJ3364MC, MAJ3364MP

MAJ3182 MAJ3182MC, MAJ3182MP

MAJ3091 MAJ3091MC, MAJ3091MP

viii C141-E103-01EN

Important Alert Items

Important Alert Messages

The important alert messages in this manual are as follows:

A hazardous situation could result in minor or moderate personal injury if the

user does not perform the procedure correctly. This alert signal also indicates

that damages to the product or other property may occur if the user does not

perform the procedure correctly.

Task Alert message Page

Mounting Installation For MAH and MAJ series, Reed Solomon codes are applied for

their ECC.

The sector-data is divided into 4 interleaving sectors, and ECC is

performed in each sector where the maximum number of errors (up

to 5 byte) can be corrected. [Total maximum byte: 5 byte x 4 (

interleave) = 20 byte]

If the error of read sector keeps allowable error byte number,

correction is performed.

However, if error byte exceeds its allowable number, correction

may not be performed properly.

Data loss

1. The user must not change the setting of terminals not described

in this section. Do not change setting status set at factory

shipment.

2. Do not change the setting of terminals except following setting

pins during the power is turned on.

• Write protect: CN2 9-10

3. To short the setting terminal, use the short plug attached when

the device is shipped from the factory.

Damage

1. Check that system power is off before connecting or

disconnecting cables.

2. Do not connect or disconnect cables when power is on.

Damage

1. Be careful of the insertion directions of the SCSI connectors.

With the system in which terminating resistor power is supplied

via the SCSI cable, if the power is turned on, the overcurrent

protection fuse of the terminating resistor power supplier may

be blown or the cable may be burnt if overcurrent protection is

not provided.

When the recommended parts listed in Table 4.2 are used,

inserting the cables in the wrong direction can be prevented.

2-5

5-5

5-11

C141-E103-01EN ix

Task Alert message Page

Mounting Installation 2. To connect SCSI devices, be careful of the connection position

of the cable. Check that the SCSI device with the terminating

resistor is the last device connected to the cable.

Data loss

When the SEND DIAGNOSTIC command terminates with the

CHECK CONDITION status, the INIT must collect the error

information using the REQUEST SENSE command. The

RECEIVE DIAGNOSTIC RESULTS command cannot read out

the error information detected in the self-diagnostics.

Caution

1. To avoid shocks, turn off the power before mounting or

removing a PCA, and before connecting or disconnecting a

cable, connector, or plug.

2. To avoid injury, do not touch the mechanical assembly during

disk drive operation.

3. Do not use solvents to clean the disk drive.

Caution

1. Always ground yourself with a wrist strap connected to ground

before handling. ESD (Electrostatics Discharge) may cause

the damage to the device.

2. To prevent electrical damage to the disk drive, turn the power

off before mounting or removing a PCA or connecting or

disconnecting a cable, connector, or plug.

3. Do not turn the power on while removing a PCA. This

operation is required to prevent unexpected or unpredictable

operation.

4. Do not use a conductive cleaner to clean a disk drive assembly.

5. Open all ventilation holes to prevent overheating of electric

circuits.

6. Ribbon cables are marked with a colored line. Connect the

ribbon cable to a cable connector with the colored wire

connected to pin 1.

Damage

Do not open the DE in the field because it is completely sealed.

Data loss

Save data stored on the disk drive before requesting repair. Fujitsu

does not assume responsibility if data is destroyed during servicing

or repair.

Caution

Never open the disk enclosure in the field. Opening the disk

enclosure in the field may cause an irreparable fault.

6-4

6-5

6-6

6-7

6-15

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Fujitsu Stockage

Fujitsu

Fujitsu MHV2060AT Manuel utilisateur

Fujitsu

Fujitsu MHV2160BT - 160GB SATA/150 4200RPM 8MB Notebook Hard... Manuel utilisateur

Fujitsu

Fujitsu HandyDrive-5 Manuel utilisateur

Fujitsu

Fujitsu MHU2100AT Manuel utilisateur

Fujitsu

Fujitsu MAB3045 Manuel utilisateur

Fujitsu

Fujitsu MBA3300FD Manuel utilisateur

Fujitsu

Fujitsu ETERNUS2000 200 Mode d’emploi

Fujitsu

Fujitsu ETERNUS LT260 Manuel utilisateur

Fujitsu

Fujitsu ETERNUS DX Disk Manuel utilisateur

Fujitsu

Fujitsu Eternus DX500 S3 Guide d'installation

Fujitsu

Fujitsu ETERNUS LT20 S2 Manuel utilisateur

Fujitsu

Fujitsu MAP3147NP Manuel utilisateur

Fujitsu

Fujitsu ETERNUS LT140 Manuel utilisateur

Fujitsu

Fujitsu MAX3073NC SCSI,80, DC961,Hard Manuel utilisateur

Fujitsu

Fujitsu Eternus DX80 S2 Manuel utilisateur

Fujitsu

Fujitsu ETERNUS AB Series Instructions de montage

Fujitsu

Fujitsu ETERNUS DX60 S2 Manuel utilisateur

Fujitsu

Fujitsu ETERNUS Mode d’emploi

Fujitsu

Fujitsu Eternus DX80 S2 Manuel utilisateur

Fujitsu

Fujitsu MJA2500BH - Mobile 500 GB Hard Drive Manuel utilisateur

Fujitsu

Fujitsu Eternus DX500 S3 Manuel utilisateur

Fujitsu

Fujitsu PG-HD9G1C Manuel utilisateur

Fujitsu

Fujitsu MHC2032AT Manuel utilisateur

Fujitsu

Fujitsu ETERNUS DX Disk Manuel utilisateur

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur