Frequency Central MU System X Lowpass Filter Manuel

Frequency central

Build documentation for:

MU system X

Lowpass Filter

Based on the Roland System 100m VCF with additional 12dB/oct output. MU System X

Lowpass Filter features: Main PCB, Sockets PCB x 7

Key to PCB screen print:

n: This signifies NPN BC547 transistors. Note the correct pinout as shown by the half circles.

p: This signifies PNP BC557 transistors. Note the correct pinout as shown by the half circles.

f: This signifies 2N5485 FETs. Note the correct pinout as shown by the half circles.

The PCB shows the correct orientation for BC547/BC557. Other transistor types can be used

(eg 2N3904/2N3906), but please observe the correct pinout. Please observe the correct

polarity of the electrolytic capacitors.

Bill of Materials

100R x 1

560R x 8

1K5 x 1

1K8 x 1

5K6x 1

6K8 x 1

10K x 6

15K x 5

22K x 4

27K x 1

33K x 3

68K x 6

100K x 8

150K x 1

270K x 1

1M x 1

All resistors ¼ watt

metal film

470pF x 4

22uF electrolytic x 8

47uF electrolytic x 2

10K thermistor x 1

TL071 x 2

LM13700 x 2

BC547 x 3

BC557 x 1

2N5485 x 4

1N4148 x 2

8 pin socket x 2

16 pin socket x 2

A100K x 2

B100K x 3

C100K x 1*

(or these)

(or C50K)

10K trimmer x 1

100K trimmer x 1

6.3mm socket x 7

Male 40 pin header

x 2

6 pin female header

x 7

DOTCOM 6 pin

header

* Circuit calls for C100K. C50K is cool too. If you can’t get C50K, use B100K instead.

Main PCB assembly - FRONT

1. Solder all resistors.

2. Solder all IC sockets

3. Solder all non-electrolytic capacitors

4. Solder all transistors and the thermistor

5. Solder the 6 x Alpha pots. Make sure they fit snug to the PCB.

Main assembly –REAR

1. Solder all trimmers

2. Solder all of the 6 pin female headers. These will later accept the Socket PCBs

3. Solder the DOTCOM power header. Don’t for get to make it ‘keyed’ by removing the

second pin in (the PCB won’t accept it otherwise – it’s keyed too!)

4. Solder the electrolytic capacitors

Socket PCB

1. Solder the 7 sockets to the 7 Socket pcbs,

socket sits on it’s silkscreen footprint

Final Assembly

1. Present the pcb to the panel, and bolt the two together using the

washers and nuts for the pots and switch

2. Cut 7 pieces of male header to be 6 pins wide. Place the long end of each into the 7

female headers.

3. Present each socket pcb assembly to the main pcb, bolt into place, making sure that

the male headers line up with their places on the socket pcbs. Solder the male

headers to the sockets pcbs.

Calibration

1. V/Oct trimmer: turn Resonance all the way to self oscillation. Patch a 1V/oct source

into CV input 1, with the attenuator fully clockwise. Play octaves and adjust the

V/Oct trimmer until they are spot on.

2. Offset trimmer: you want to tweak this so that the filter is fully open when the

Cutoff pot is fully clockwise.

RDH 27/07/19

http://www.frequencycentral.co.uk/

Table des matières

Autres manuels Frequency Central Unité de contrôle

Frequency Central

Frequency Central Raging Bull 3.0 Manuel

Frequency Central

Frequency Central System X Amplifier Manuel

Frequency Central

Frequency Central State 700 MK2 Manuel

Frequency Central

Frequency Central Cosmic Background Manuel

Frequency Central

Frequency Central Deep Thought Manuel

Frequency Central

Frequency Central XVCO Manuel

Frequency Central

Frequency Central Stasis Leak Manuel

Frequency Central

Frequency Central System X CV Mixer Manuel

Frequency Central

Frequency Central Looking glass Manuel utilisateur

Frequency Central

Frequency Central Continuum Phaser ii Manuel

Frequency Central

Frequency Central MU System X Dual Amplifier Manuel

Frequency Central

Frequency Central Wave Runner Manuel

Frequency Central

Frequency Central Stasis Leak Manuel utilisateur

Frequency Central

Frequency Central MU Wave Runner LFO Manuel

Frequency Central

Frequency Central Continuum Phase Shifter Manuel

Frequency Central

Frequency Central Waverider VCDO MKii Manuel

Frequency Central

Frequency Central Raging Bull Manuel

Frequency Central

Frequency Central Process 26 Manuel

Frequency Central

Frequency Central Waverider Digital VCO Manuel

Frequency Central

Frequency Central Raging Bull 2.0 Manuel

Frequency Central

Frequency Central Polygraf Manuel

Frequency Central

Frequency Central CEMvelope Manuel

Frequency Central

Frequency Central Dual XVCA Manuel

Frequency Central

Frequency Central System X Filter Manuel

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur