Frequency Central Continuum Phaser ii Manuel

Build documentation for:

continuum phaser ii

An original design by

Frequency central

Rev 3 / May 2014

Main PCB: Panel PCB:

Key to PCB screen print:

n: This signifies NPN BC547 transistors. Note the correct pinout as shown by the half circles.

p: This signifies PNP BC557 transistors. Note the correct pinout as shown by the half circles.

Please observe that the TL084 is ‘the other way round’ with respect to the LF351 and 2 x

LM13700.

Please observe the correct polarity of the 2 diodes and 8 electrolytic capacitors. The 6 x

22uF are configured in sets of 2 back to back (negative to negative).

The PCB shows the correct orientation for BC547/BC557. Other transistor types can be used

(eg 2N3904/2N3906), but please observe the correct pinout.

Bill of materials

100R x 1

1K5 x 1

1K8 x 4

10K x 18

15K x 2

27K x 11

100K x 6

150K x 1

270K x 1

1M x 1

4n7 x 1

10n x 4

47n x 1

22uF electrolytic x 6

47uF electrolytic x 2

LF351 x 1 (or TL071)

LM13700 x 2

TL084 x 1

BC547 x 1

BC557 x 1

1N4148 x 2

A100K x 3

B100K x 3

All pots are 9mm Alpha PCB

mount

10K trimmer x 1

100K trimmer x 1

All trimmers are 6mm

SPDT toggle x 1

Power header

Male header strip

Female header strip

Kobiconn sockets x 5

Main PCB:

Populate the Main PCB as shown on the silkscreen, starting with the lowest profile

components, so:

Resistors, diodes

IC sockets

Non-electrolytic capacitors, transistors, trimmers

Power header

Electrolytic capacitors

Finally, cut 3 male header strips to the correct lengths (5, 5, 9) and solder to the PCB so that

the long legs stick out of the rear of the PCB.

Panel PCB:

Populate the Panel PCB as shown on the silkscreen in this order:

100R Resistor

Electrolytic capacitors (the legs will need to be bent by 90° so that the caps lie on the

PCB)

Potentiometers (bend back the mounting lugs , then solder the middle lug in place.

Reflow and adjust as necessary so that they all lie correctly. Solder lugs 1, 3 and the

mounting lugs)

SPDT switch, making sure it’s flush as can be

Cut 3 female header strips to the correct lengths (5, 5, 9) and solder to the PCB so that the

black parts stick out of the rear of the PCB.

Now, place the 5 sockets onto the PCB with their ground lugs pointing towards the bottom

of the PCB. Don’t solder them in place yet! Assemble the panel to the panel PCB, put on the

pots/switch washers and tighten up the nuts. Now set the sockets to the panel using the

nuts, making sure they all sit right. Place the assembly face down and solder the sockets in

place. This process should allow a small space to be created between the rear of the

sockets’ bodies and the PCB, allowing jacks to go in balls-deep (!). Everything should line up

nicely now!

Take the whole thing apart, ie remove the nuts/washers and take the panel away from the

panel PCB. Now solder solid core (cut off resistor legs) between the sockets’ ground tabs

and the adjacent ground pads on the PCB.

Put the panel back together with the panel PCB, plug the Main PCB into the Panel

PCB…you’re done!

Trimmers: turn both fully anti-clockwise (that’s how I like ‘em), adjust to taste.

RDH 19th July 2014

http://www.frequencycentral.co.uk/

Autres manuels Frequency Central Unité de contrôle

Frequency Central

Frequency Central System X Amplifier Manuel

Frequency Central

Frequency Central Raging Bull 3.0 Manuel

Frequency Central

Frequency Central MU Wave Runner LFO Manuel

Frequency Central

Frequency Central Bartos Flur Rev(2) Manuel

Frequency Central

Frequency Central Process 26 Manuel

Frequency Central

Frequency Central MU System X Dual ADSR Manuel

Frequency Central

Frequency Central System X Filter 2 Manuel

Frequency Central

Frequency Central Stasis Leak Manuel

Frequency Central

Frequency Central Cosmic Background Manuel

Frequency Central

Frequency Central Meth Amp Rev.2 Manuel

Frequency Central

Frequency Central Seismograf Manuel

Frequency Central

Frequency Central XVCO Manuel

Frequency Central

Frequency Central Waverider Digital VCO Manuel

Frequency Central

Frequency Central More VCAs Manuel

Frequency Central

Frequency Central Looking glass Manuel utilisateur

Frequency Central

Frequency Central MU System X Dual Amplifier Manuel

Frequency Central

Frequency Central Raging Bull Manuel

Frequency Central

Frequency Central Polygraf Manuel

Frequency Central

Frequency Central Infinitely Maybe Manuel

Frequency Central

Frequency Central Stasis Leak Manuel

Frequency Central

Frequency Central Deep Thought Manuel

Frequency Central

Frequency Central Waverider VCDO MKii Manuel

Frequency Central

Frequency Central CEMvelope Manuel

Frequency Central

Frequency Central Raging Bull 2.0 Manuel

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur