Frequency Central Deep Thought Manuel

Frequency central

Build documentation for:

Deep thought

Boolean Logic module featuring code by Jetroid

Deep Thought is a Boolean logic module with two distinct sections. The upper section features

addressable Boolean logic, with any one of NOT A, NOT B, AND, NAND, OR, NOR, XOR and XNOR

being chosen either via knob or via CV input. The lower section features simultaneous outputs of

NOT A, NOT B, AND, NAND, OR, NOR, XOR and XNOR.

Key to PCB screen print:

n: This signifies NPN BC547 transistors. Note the correct pinout as shown by the half circles.

The PCB shows the correct orientation for BC547. Other similar transistor types can be used,

but please observe the correct pinout.

Please observe the correct polarity of the electrolytic capacitors.

Bill of Materials

1K x 15

4K7 x 13

10K x 6

91K x 2

100K x 6

240K x 2

All resistors ¼ watt

metal film.

100nF

10uF x 1

47uF x 2

Deep Thought PIC

TL072 x 2

BC547 x 4

78L05

3mm red LED x 13

8 pin IC socket x 2

14 pin IC socket x 1

Alpha 9mm B100K x 1

3.5mm socket x 13

Male header

(cut to size)

Female header

(cut to size)

Power header

(cut to size)

Knob x 1

Main PCB assembly

1. Solder all resistors

2. Solder all three IC sockets

3. Solder the 100nF capacitor

4. Solder all four transistors and 78L05 –watch the polarity!

5. Solder the power header.

6. Solder all electrolytic capacitors

7. Cut male headers to size and solder them into place. Make sure that they stick out of

the bottom of the PCB.

Pots ‘n’ sockets PCB

1. Place all sockets on the PCB, making sure the ground tabs line up with the PCB’s

ground pads –be careful here as there are four different orientations - then place

the panel over them. This will assure that the sockets are correctly positioned. Flip

the whole lot over and solder the sockets into place.

2. Use cut off resistor legs to connect the sockets’ ground tabs line up with the PCB’s

ground pads.

3. Solder the potentiometer in place

4. Cut female headers to size and solder them into place. Make sure that they stick out

of the bottom of the PCB.

5. Put all thirteen LEDs through their pads –be careful here as there are two different

orientations. Present the panel to the PCB, flip the whole lot over, make sure the

LEDs stick though the holes in the panel, solder in place.

There’s no calibration to do! But –make sure that you plug the main PCB into the pots ‘n’

sockets PCB the right way around!

RDH 09/06/18

http://www.frequencycentral.co.uk/

Autres manuels Frequency Central Unité de contrôle

Frequency Central

Frequency Central Meth Amp Rev.2 Manuel

Frequency Central

Frequency Central Looking glass Manuel utilisateur

Frequency Central

Frequency Central System X CV Mixer Manuel

Frequency Central

Frequency Central Stasis Leak Manuel

Frequency Central

Frequency Central XVCO Manuel

Frequency Central

Frequency Central Process 26 Manuel

Frequency Central

Frequency Central Stasis Leak Manuel

Frequency Central

Frequency Central Whiteface Manuel

Frequency Central

Frequency Central Raging Bull 2.0 Manuel

Frequency Central

Frequency Central System X Amplifier Manuel

Frequency Central

Frequency Central Stasis Leak Manuel utilisateur

Frequency Central

Frequency Central State 700 Manuel

Frequency Central

Frequency Central Infinitely Maybe Manuel

Frequency Central

Frequency Central Continuum Phase Shifter Manuel

Frequency Central

Frequency Central Waverider VCDO MKii Manuel

Frequency Central

Frequency Central Dual XVCA Manuel

Frequency Central

Frequency Central Raging Bull 3.0 Manuel

Frequency Central

Frequency Central MU System X Lowpass Filter Manuel

Frequency Central

Frequency Central MU System X Dual ADSR Manuel

Frequency Central

Frequency Central Seismograf Manuel

Frequency Central

Frequency Central Raging Bull Manuel

Frequency Central

Frequency Central Cosmic Background Manuel

Frequency Central

Frequency Central More VCAs Manuel

Frequency Central

Frequency Central Bartos Flur Rev(2) Manuel

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur