Flying Industry Development 0020130 Manuel utilisateur

SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD

Http://www.carymart.com E-Mail: sale@carymart.com

RF Wireless Receiver (Model 0020130 S1PFC-AC220)

Features:

Application: It can be used in rolling blinds, rolling doors, projection screens, awnings, pumps, winches, conveyors or other appliances and

equipments withAC motors, it can remote control AC motor rotates in the positive or reversal direction.

Wireless control, easy to install.

Waterproof: The receiver has waterproof case and waterproof connector, it can be installed outdoors.

You can rotate a motor in the positive or reversal direction with the transmitter (remote control) from any place within a reliable distance.

The RF wireless signal can pass through walls, floors and doors.

High Power: Each channel can work at maximum current 30A.

With limit control terminals: You can connect limit switches or sensors to stop the motor.

With wired control terminals: You can connect manual switches or external devices (with low level output signal, such as sensors) to control the

motor.

Design with low-power and high-speed CMOS technology.

You can turn on/ off the receiver with transmitter (remote control) from any place within a reliable distance.

With reverse power protection and over current protection.

Reliable control: The receiver only works with the transmitter which use same code.

One/several transmitters can control one/several receivers simultaneously.

You can use two or more units in the same place.

Receiver Parameters:

Model No: S1PFC-AC220

Control Mode: Latched or Momentary

Coding Type: Fixed code or learning code

Coding Setting: By learning

Power Supply (Operating Voltage): AC100~240V (110V/120V/220V/240V)

Output: AC100~240V (110V/120V/220V/240V)

Working Frequency: 315MHz / 433MHz

Channel: 1 CH, can work with 1 AC motor

Static Current: ≤6mA

Maximum Working Current: 30A / each channel, so motor's maximum starting current can not exceed 30A.

PCB Size: 140mm x 73mm x 18mm

Case Size: 192mm x 100mm x 45mm

Matching Transmitters:

This receiver can work with different transmitters. When you set the receiver in momentary mode, it should work with two button transmitters, such as

model C-2-2 (100M), CWB-2 (50M, waterproof), CP-2 (500M), CV-2-2 (500M), or CB-2 (1000M) etc. When you set the receiver in latched mode, it

should work with three or four button transmitters, such as model C-3-2,(100M), CWB-3 (50M, waterproof), CB-3 (1000M),CP-4 (500M), or CV-4-2

(500M) etc.

Working Range:

With a transmitter (such as CV-4-2) to form a complete set, the working distance can reach 500M in an open ground. The maximum working distance

500M is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by trees,

walls or other constructions, and will be interfered by other wireless signals. Therefore, the actual distance may or may not reach 500M. If you want to

have a further working range, you can install an external antenna to the receiver, and you also can use a powerful transmitter, such as CB

transmitters.

Usage (with transmitter CV-4-2):

Connect live wire to terminal “L”and neutral wire to terminal “N”. Then connect AC motor to terminals “UP”, “COM” and “DOWN”. You can exchange

“UP” and “DOWN”wires of motor to change the rotating direction of motor.

Setting control mode Latched: Do not connect Jumper-1 (CN1) or Jumper-2 (CN2)

Press button ▲: motor rotates in positive direction.

Press button ▼: motor rotates in reversal direction.

Press button ■: motor stops.

Setting control mode Momentary: Only connect Jumper-1 (CN1)

Press and hold button ▲: motor rotates in positive direction. Release button ▲: Motor stops.

Press and hold button▼: motor rotates in reversal direction. Release button ▼: Motor stops.

Limit control terminals:

Limit control terminals S1 and S2 are normally open, you can connect limit switches or sensors (normally open type) to terminals S1 and S2, and

then you can use limit switches or sensors to stop the motor.

When motor rotates in positive direction, if connect two terminals of S1, the motor will stop automatically.

When motor rotates reversal direction, if connect two terminals of S2, the motor will stop automatically.

SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD

Http://www.carymart.com E-Mail: sale@carymart.com

Wired control terminals:

You can connect manual switches, external devices or sensors (with low level output signal) to control the motor.

1) The manual switches:

You can connect manual switches to terminals “Signal 1+”, “Signal 1-”, “Signal 2+”, “Signal 2-”, then you can use manual switches to control the

motor.

When connect terminals “Signal 1+”and “Signal 1-”, motor rotates in positive direction.And when disconnect “Signal 1+”and “Signal 1-”, motor stops.

When connect terminals “Signal 2+”and “Signal 2-”, motor rotates in reversal direction. And when disconnect “Signal 2+”and “Signal 2-”, motor

stops.

2) Signal input:

You can connect external devices (with low level output signal) to terminals “Signal 1+”, “Signal 1-”, “Signal 2+”, “Signal 2-”, then the external

device’s output signal can control the motor.

When the external device outputs low level signal to terminal “Signal 1-”and “Signal 1+“, motor rotates in positive direction.

When the external device outputs low level signal to terminal “Signal 2-”and “Signal 2+“, motor rotates in reversal direction.

How to pair the transmitter to the receiver:

1) Press the learning button of receiver for 1- 2 seconds; signal LED on the receiver is on. The receiver enters into status of LEARNING.

2) Press any one button on transmitter. If signal LED flashes quickly 15 times and turns off, it means learning is successful.

3) When receiver is in the status of LEARNING, press again the button of receiver, signal LED turns off, learning process will be discontinued.

4) The receiver can learn several remote controls with different codes.

Delete all transmitters:

We have learned remote control to the receiver. If you don’t want the receiver to work with the remote control, you can delete all codes of remote

controls, which are stored in the receiver.

Operation: Press and hold the button of receiver until signal LED flashes slowly; release the button, LED keeps slow flash. That means all stored

codes have been deleted successfully.

SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD

Http://www.carymart.com E-Mail: sale@carymart.com

CN2

CN1

Control AC Motor

External Device

RF module

Antenna

Signal LED

Learning Button

Limit Terminals

AC Motor

Power Supply

DOWN

Relay1

Relay2

Power LED

Status LED 1

Status LED 2

Live wire

Neutral wire

COM

Signal 1+

Signal 1-

Signal 2-

Signal 2+

AC Power Supply

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Flying Industry Development Télécommande

Flying Industry Development

Flying Industry Development S1XB-AC220-ANT2 Manuel utilisateur

Flying Industry Development

Flying Industry Development S1UD-DC06 Manuel utilisateur

Flying Industry Development

Flying Industry Development 0020027 Manuel utilisateur

Flying Industry Development

Flying Industry Development S1X2-DC Manuel utilisateur

Flying Industry Development

Flying Industry Development 0020703 Manuel utilisateur

Flying Industry Development

Flying Industry Development S2T-DC06-ANT2 Manuel utilisateur

Flying Industry Development

Flying Industry Development 002028 Manuel utilisateur

Flying Industry Development

Flying Industry Development 0020386 Manuel utilisateur

Flying Industry Development

Flying Industry Development 0020794 Manuel utilisateur

Flying Industry Development

Flying Industry Development S4PUA-AC220 Manuel utilisateur

Flying Industry Development

Flying Industry Development S1PF3-DC12 Manuel utilisateur

Flying Industry Development

Flying Industry Development 0020057 Manuel utilisateur

Flying Industry Development

Flying Industry Development 0020481 Manuel utilisateur

Flying Industry Development

Flying Industry Development 15S1PXB-DC12+1CP-15 Manuel utilisateur

Flying Industry Development

Flying Industry Development S1DA-DC09 Manuel utilisateur

Flying Industry Development

Flying Industry Development S1X-DC06 Manuel utilisateur

Flying Industry Development

Flying Industry Development 3S2UB-DC12+CV-6 Manuel utilisateur

Flying Industry Development

Flying Industry Development Z-06 Manuel utilisateur

Flying Industry Development

Flying Industry Development 00200261 Manuel utilisateur

Flying Industry Development

Flying Industry Development 6S2UB-DC12+1CV-12 Manuel utilisateur

Flying Industry Development

Flying Industry Development S1F2-DC06 Manuel utilisateur

Flying Industry Development

Flying Industry Development S1PS1-DC06-ANT2 Manuel utilisateur

Flying Industry Development

Flying Industry Development S2T-DC06-ANT1 Manuel utilisateur

Flying Industry Development

Flying Industry Development S1PF-DC12 Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation