Flying Industry Development S1PX-DC-ANT2 Manuel utilisateur

SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD

Http://www.carymart.com E-Mail: sale@carymart.com

RF Wireless Receiver (Model 0020438 S1PX-DC-ANT2)

Feature:

Application: It can be used in industry automation, agriculture automation and home automation, such as factory, house, farm, pasture, vehicle, ship,

offshore operation, aerial vehicle, field call, etc. It can remote control equipments on land, water and air, such as remote control lights, sirens, locks,

motors, fans, pumps, doors, windows, electric solenoid valves, security alarm, business signs and various devices.

Wireless remote control, easy to install.

Super long working range, with a transmitter to form a complete set, the working distance can reach 2000m in an open ground.

Waterproof: The receiver has waterproof case and waterproof connector, it can be installed outdoors.

Power Supply: Four working voltage versions, DC 6V, 9V, 12V, 24V.

DC Power Output: It can control DC equipment with voltage DC 6V / 9V / 12V / 24V.

High Power: Each channel can work at maximum current 30A, such as 360W/12V, 180W/6V, 270W/9V or 720W/24V.

With wired control terminals: You can connect sensors, limit switches, manual switches or external devices to control the receiver.

With external magnetic sucker antenna and a 1.5 meters cable, the antenna can be installed outside the building to get better working distance.

You can control the equipments by using the receiver with transmitter (remote control) from any place within a reliable distance.

Wireless RF signal can pass through walls, floors, doors or windows.

With characteristics of reverse power protection and over current protection.

Reliable control: The code has thousands of different combinations, and the receiver only works with the transmitter which use the same code.

One/several transmitters can control one/several receivers simultaneously.

You can use two or more units in the same place.

Receiver Parameters:

Model No.: S1PX-DC06 -ANT2/ S1PX-DC09 -ANT2 / S1PX-DC12 -ANT2 / S1PX-DC24 -ANT2

Power Supply (Operating Voltage): DC6V (S1PX-DC06-ANT2), DC9V±1V (S1PX-DC09-ANT2), DC12V±1V (S1PX-DC12-ANT2), DC24V±2V

(S1PX-DC24 -ANT2)

Output: DC6V (S1PX-DC06 -ANT2), DC9V (S1PX-DC09 -ANT2), DC12V (S1PX-DC12 -ANT2), DC24V (S1PX-DC24 -ANT2)

Wire range for the terminals: 22-9AWG

Working Frequency: 315MHz / 433MHz

Channel: 1 CH

Control Modes: Toggle, Momentary, Latched

Static Current: ≤6mA

Operating Temperature: -20 °C to +70 °C

Maximum Working Current: 30A

PCB size: 90mm x 59mm x 18mm

Case size: 100mm x 68mm x 50mm

External Magnetic Sucker Antenna:

Frequency Range: 300~450MHz

Impedance: 50Ω

Antenna Length: 15cm

Cable Length: 1.5m, we also can offer longer cable, such as 5 meters, 10 meters or 30 meters.

Anti-interference, waterproof, shielded wire set inside.

Magnetic stand design for easy to install.

Matching Transmitters For Receiver:

The receiver can work with different transmitters, such as model C-1 / C-2 (100M), CWB-1 / CWB-2 (50M, waterproof), CP-1 / CP-2 (500M), or CB-1

/ CB-2 (1000M) etc.

When you set the receiver in toggle or momentary mode, it should work with single button transmitter, such as model C-1 (100M), CWB-1 (50M,

waterproof), CP-1 (500M), or CB-1 (1000M) etc. When you set the receiver in latched mode, it should work with two buttons transmitter, such as

model C-2 (100M), CWB-2 (50M, waterproof), CP-2 (500M), CV-2 (500M), or CB-2 (1000M) etc.

Working Range:

Super long range, with a transmitter (such as CB-2) to form a complete set, the maximum working distance can reach 2000M in an open ground.

The maximum working distance is an ideal range , it shall be operated with no barriers and interference in an open ground. But in the practice, it will

be hindered by trees, walls or other constructions, and will be interfered by other wireless sign. Therefore, the actual distance may not reach this

maximum working distance.

Usage (with the transmitter CB-2):

The receiver can be used to control DC 6V / 9V / 12V / 24V equipments. If the power supply of those equipments is DC 12V, you should choose the

receiver with same DC 12V version; and if the power supply of those equipments is DC 24V, you should choose the receiver with same DC 24V

version.

Wiring:

If you want to control a DC 12V lamp, do as following:

1) Connect the positive pole of DC power supply to terminal “L / +” of INPUT, and connect the negative pole of DC power supply to terminal “N / -”of

INPUT.

2) Connect the positive pole of lamp to terminal "L / +" of OUTPUT, and connect the negative pole of lamp to terminal "N / -" of OUTPUT.

Setting different control modes:

SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD

Http://www.carymart.com E-Mail: sale@carymart.com

We have set the receiver in toggle mode before delivery, if you want to use other modes, do as following operation.

1) Setting control mode Toggle: Only connect Jumper-2.

Control mode Toggle (with transmitter CB-1): Press -> On; Press again -> Off.

Press button of the transmitter: Output terminals outputs DC power, and the lamp is turned on.

Press button again: Output terminals stops outputting, and the lamp is turned off.

2) Setting control mode Momentary: Only connect Jumper-1.

Control mode Momentary (with transmitter CB-1): Press and hold -> On; Release -> Off.

Press and hold button of the transmitter: Output terminals outputs DC power, the lamp is turned on.

Release button of the transmitter: Output terminals stops outputting, the lamp is turned off.

3) Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.

Control mode Latched (with transmitter CB-2): Press -> On, Press another button -> Off.

Press button A of the transmitter: Output terminals outputs DC power, and the lamp is turned on.

Press button B of the transmitter: Output terminals stops outputting, and the lamp is turned off.

Wired control terminals:

The receiver has wired control terminals, and you can connect external devices, sensors, or manual switches to the receiver's manual terminals, then

use them to trigger the receiver.

1) By low level signal:

You can connect external devices (with low level output signal) to trigger the receiver.

When external device outputs low level signal to terminals 1 (Signal +) and terminal 2 (Signal -), the relay is activated, and Output terminals outputs

DC power, and the lamp is turned on.

When external device stops to output signal, the relay is deactivated, and Output terminals stops outputting, and the lamp is turned off.

2) By NO/NC contact:

You can connect manual switches (with NO/NC contact) to trigger the receiver.

When connect terminals 1 and 2 by manual switch, the relay is activated. Output terminals outputs DC power, and the lamp is turned on.

When disconnect terminals 1 and 2 by manual switch, the relay is deactivated. Output terminals stops outputting, and the lamp is turned off.

How to pair the transmitter to the receiver:

1) Press the learning button of receiver for 1- 2 seconds; signal LED on the receiver is on. The receiver enters into status of LEARNING.

2) Press any one button on transmitter. If signal LED flashes quickly 15 times and turns off, it means learning is successful.

3) When receiver is in the status of LEARNING, press again the learning button, signal LED turns off, learning process will be discontinued.

4) The receiver can learn several remote controls with different codes.

Delete all transmitters:

We have learned remote control to the receiver. If you don’t want the receiver to work with the remote control, you can delete all codes of remote

controls, which are stored in the receiver.

Operation: Press and hold the learning button of receiver until signal LED flashes slowly; release the button, LED keeps slow flash. That means all

stored codes have been deleted successfully.

SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD

Http://www.carymart.com E-Mail: sale@carymart.com

DC Power Supply

Control DC Lamp

Relay

CN1

Status LED

Power LED

Signal LED

Learning Button

External Device

RF module

Antenna

Signal +

Signal -

L/+

N/-

DC Lamp

N/-

L/+

CN2

INPUT

OUTPUT

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Flying Industry Development Télécommande

Flying Industry Development

Flying Industry Development S4PUA-AC220 Manuel utilisateur

Flying Industry Development

Flying Industry Development S1F2-DC06 Manuel utilisateur

Flying Industry Development

Flying Industry Development S1DA-DC09 Manuel utilisateur

Flying Industry Development

Flying Industry Development S1UD-DC06 Manuel utilisateur

Flying Industry Development

Flying Industry Development 3S2UB-DC12+CV-6 Manuel utilisateur

Flying Industry Development

Flying Industry Development S1PF3-DC12 Manuel utilisateur

Flying Industry Development

Flying Industry Development 0020794 Manuel utilisateur

Flying Industry Development

Flying Industry Development S1PS1-DC06-ANT2 Manuel utilisateur

Flying Industry Development

Flying Industry Development S4C-DC06 Manuel utilisateur

Flying Industry Development

Flying Industry Development 0020109 Manuel utilisateur

Flying Industry Development

Flying Industry Development 002028 Manuel utilisateur

Flying Industry Development

Flying Industry Development S1PUB-DC09 Manuel utilisateur

Flying Industry Development

Flying Industry Development 0020386 Manuel utilisateur

Flying Industry Development

Flying Industry Development 15S1PXB-DC12+1CP-15 Manuel utilisateur

Flying Industry Development

Flying Industry Development S1F2-DC06 Manuel utilisateur

Flying Industry Development

Flying Industry Development S1UD-DC06 Manuel utilisateur

Flying Industry Development

Flying Industry Development S1XB-AC220-ANT2 Manuel utilisateur

Flying Industry Development

Flying Industry Development S1X-DC06 Manuel utilisateur

Flying Industry Development

Flying Industry Development S2PX-DC09-ANT2 Manuel utilisateur

Flying Industry Development

Flying Industry Development S1X2-DC Manuel utilisateur

Flying Industry Development

Flying Industry Development 0020057 Manuel utilisateur

Flying Industry Development

Flying Industry Development S1XB-DC06 Manuel utilisateur

Flying Industry Development

Flying Industry Development 6S2UB-DC12+1CV-12 Manuel utilisateur

Flying Industry Development

Flying Industry Development S2T-DC06-ANT1 Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation